LI-COR LI-800 Leitfaden

1. Turn the LI-800 off. Remove the six screws on the LI-800 top panel and remove the cover.

2. Unscrew the tube retaining nuts on the inner air port fittings. Remove the tubing from both air ports. Leave the tubing connected

to the source and detector housings.

3. There are ribbon cables (Figure 1 below) connected to the circuit boards on the source and detector housings. Pull straight out on

the connector that is attached to each ribbon cable. The optical bench can now be removed from the foam casing.

Source Detector

Air In Air Out

PCBPCB

Optical Bench

Hose Barb

Bev-a-line Tubing

Ribbon Cable

Connector

4. There are four screws on the source and detector circuit boards that must be removed. Remove the four screws in the corners of

the boards, as shown below (they are slightly larger than the other four screws). Do not remove the remaining four screws.

Remove these

4 screws

5. The source and detector housings (with attached circuit boards) can now be removed. The bench will appear as shown below. Be

careful not to lose the O-ring on either end of the bench.

O-ring

Top View

End View

6. Install the source and detector housings on the gold-plated optical path cylinder. Make sure that both source and detector hous-

ings have an O-ring installed, as shown in Step 5 above. The orientation of the cylinder is not important; either end can be

inserted into the source or detector housing. Note: There is no need to grease the O-ring; simply press into place.

LI-800 GasHound

Source/Detector Replacement Instructions

7. Carefully remove the 10-pin connector that was attached to the source housing circuit board from the main circuit board. Reat-

tach the 10-pin connector to one of the connectors shown below, depending on the length of the optical bench being installed.

Fuse

LEDs

Connector for 2”

optical bench

Source Detector

Connector for 5.5"

optical bench (not

shown, beneath

tubing)

Figure 4. Location of 10-pin connectors for 5.5" and 2" optical benches.

8Install the bench with the source side on the left as you face the front of the instrument.

9. Reattach the 10-pin connectors to the source and detector housing circuit boards. Reattach the Bev-a-line tubing to the hose barbs

on the source and detector housings, and to the flow in and out ports, if necessary.

10. Re-assemble the LI-800 case. Make sure that the foam insulation on the inside top cover is positioned over the optical bench; it is

required for thermal stability.

11. Perform zero and span calibrations as described in the LI-800 Instruction Manual Section 3, Calibration Window.

LI-COR, inc. ●Environmental Division ●4421 Superior Street ●P.O. Box 4425 ●Lincoln, Nebraska 68504 USA

Phone: 402-467-3576 ● FAX: 402-467-2819

Toll-free 1-800-447-3576 (U.S. & Canada)

E-mail: envsales@env.licor.com

Internet: http://www.licor.com

AKC101

Andere Handbücher für LI-800

Inhaltsverzeichnis

Andere LI-COR Messgerät Handbücher

LI-COR

LI-COR LAI-2200 Bedienungsanleitung

LI-COR

LI-COR LI-7810 Bedienungsanleitung

LI-COR

LI-COR LI-820 Bedienungsanleitung

LI-COR

LI-COR LI-830 Leitfaden

LI-COR

LI-COR LI-250A Bedienungsanleitung

LI-COR

LI-COR LI-600N Bedienungsanleitung

LI-COR

LI-COR LI-8100A Bedienungsanleitung

LI-COR

LI-COR LI-7500 Bedienungsanleitung

LI-COR

LI-COR LI-8100 Bedienungsanleitung

LI-COR

LI-COR LI-6800 Bedienungsanleitung

LI-COR

LI-COR li-7200 Bedienungsanleitung

LI-COR

LI-COR LAI-2000 Anleitung zur Verwendung

LI-COR

LI-COR LAI-2200 Bedienungsanleitung

LI-COR

LI-COR LI-8100A Bedienungsanleitung

LI-COR

LI-COR LI-180 Bedienungsanleitung

LI-COR

LI-COR LI-800 Bedienungsanleitung

LI-COR

LI-COR LI-600 Bedienungsanleitung

LI-COR

LI-COR LI-3000C Gebrauchs- und Pflegehandbuch

LI-COR

LI-COR LI-600 Bedienungsanleitung

LI-COR

LI-COR LI-3100C Bedienungsanleitung

LI-COR

LI-COR LI-3100C Bedienungsanleitung

LI-COR

LI-COR LI-8150 Multiplexer Montage- und Bedienungsanleitung

LI-COR

LI-COR 4300 Bedienungsanleitung

LI-COR

LI-COR LI7200RS Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung