Liesegang E-motion4100 Bedienungsanleitung

.Liesegang

.elmotion4100

User's Manual

WXGA DLP Front Projector

PREFACE

ABOUT THIS MANUAL

This manual is for use with the Liesegang e.motion4100 DLP Projector. Information in this document

has been carefully checked for accuracy; however, no guarantee is given to the correctness of the

contents. The information in this document is subject to change without notice.

This document contains proprietary information protected by copyright. All rights are reserved. No part

of this manual may be reproduced by any mechanical, electronic or other means, in any form, without

prior written permission of the manufacturer

TRADEMARKS

All trademarks and registered trademarks are the property of their respective owners.

FCC COMPLIANCE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

FEDERAL COMMUNICATIONS COMISSION (FCC) STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Preface ENGLISH

PREFACE

Notices

WARNING! To meet FCC requirements, a shielded power cord is required in order to prevent

interference. It is essential that only the supplied power cord is to be used. Use only shielded

cables to connect I/O devices to this equipment. You are cautioned that changes or

modifications not approved by the party responsible for compliance could void your authority

to operate the equipment.

WARNING! The projector cooling fan continues to run for approximately 90 seconds after the

projector is turned off using the Power button on the control panel or remote control. Never

unplug the power cable to power off the projector; damage to the lamp may result.

WARNING! High brightness light source. Do not stare into the beam of light, or view directly.

Be especially careful and ensure that children do not stare directly into the beam

of light.

WARNING! To reduce the risk of fire or electric shock, do not expose this product to rain or

moisture.

CAUTION! For minimal servicing and to maintain high image quality, we recommend that you

use the projector in an environment that is smoke and dust free. When used in areas where

there is a lot of smoke or dust, the filter and lens should be cleaned often to lengthen the

service life of the projector.

WARNING! Some IC chips in this product include confidential and/or trade secret property

belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate,

distribute, reverse engineer, reverse assemble or decompile the contents thereof.

WARNING! The ventilation slots, lamp, and objects next to them may get extremely hot

during operation. Do not touch these areas until they have sufficiently cooled down.

PREFACE

PRODUCT DISPOSAL

This projector utilizes a tin-lead solder, UHP Lamp containing a small amount of mercury. Disposal of

these materials may be regulated due to environmental considerations.

Caution regarding the exhaust of the projector.

Do not put Air Conditioners or

Flowers near the exhaust

vent.

Before using the projector, please read this operation manual carefully.

To facilitate reporting the loss or theft of your Projector, record the Serial Number located on the

bottom of the projector and retain this information. Before recycling the packaging, be sure that you

have checked the contents of the carton thoroughly against the list of “Package Contents” on page 7.

WARRANTY

Promptly register the Projector’s Warranty using the REGISTRATION CARD packed with the

projector. The Warranty assures that you immediately receive the full benefit of the parts, service and

labor warranty applicable to your purchase.

Templed

STANDBY

INPUT

KEYSTONE

Focus

Zoom

LENS SHIFT (H)

LENS SHIFT (V)

ENTER

Air flow

Exhaust Vent

Air Conditioners

or Flowers

INTRODUCTION

Contents

Preface .............................................................................. 1

Notices .............................................................................. 2

Introduction

Package Contents ............................................................. 7

Features ............................................................................ 8

Components ...................................................................... 9

Projector (Front and Top View) ............................. 9

Projector (Rear View).......................................... 10

Remote Control ................................................... 11

Using the Remote Control ............................................... 12

Available Range of the Remote Control .............. 12

Inserting the Batteries ......................................... 12

Connections and Setup

Connecting the Projector to Other Devices ..................... 14

Before Setting Up................................................ 14

Connecting the Power Cord ................................ 14

Connecting to Video Equipment...................................... 15

Connecting to Video Equipment.......................... 15

Connecting to Component Video Equipment ...... 16

Connecting by Using the DVI Cable.................... 16

Connecting by Using a DVI-D to HDMI Cable..... 17

Connecting the Projector to a Computer ......................... 18

Connecting to a Computer .................................. 18

Connecting the Thumbscrew Cables............................... 19

“Plug and Play” Function ................................................. 19

Using the Adjustment Feet .............................................. 20

Adjusting the Lens........................................................... 21

Using the Lens Shift ........................................................ 21

Setting up the Screen...................................................... 22

Screen Size and Projection Distance.................. 23

Projection from behind the screen ...................... 24

Basic Operation

Image Projection ............................................................. 26

Basic Procedure.................................................. 26

Selecting the On-screen Display Language........ 28

Menu Bar Items ............................................................... 29

Using the Menu Screen................................................... 31

Menu Selections (Adjustments) .......................... 31

Adjusting the Picture ....................................................... 32

Adjusting Image Preferences .............................. 32

Adjusting Computer Images ............................................ 36

INTRODUCTION

Easy to Use Functions

Selecting the Picture Display Mode................................. 38

H-V Position Function...................................................... 41

White Enhance ................................................................ 43

Selecting the Economy Mode.......................................... 43

Setting the Power Save....................................... 43

Automatic Power Off Function......................................... 44

Source Select .................................................................. 44

OSD Timeout................................................................... 45

OSD Blending.................................................................. 46

Reversing/Inverting Projected Images............................. 46

Setting the Projection Mode ................................ 46

Deinterlace ...................................................................... 47

Reset ............................................................................... 48

Lamp Timer Reset........................................................... 48

Status Screen .................................................................. 49

Factory reset ................................................................... 49

Appendix

Maintenance.................................................................... 52

Cleaning the Ventilative Holes ........................................ 53

Cleaning the Ventilative Holes ............................ 53

About the Lamp ............................................................... 54

Caution Concerning the Lamp ............................ 54

Replacing the Lamp ............................................ 54

Temperature LED (Over Temperature)............... 55

Removing and Installing the Lamp Unit........................... 56

Resetting the Lamp Timer ............................................... 57

Connecting Pin Assignments .......................................... 58

Computer Compatibility Chart ......................................... 59

Video Compatibility Chart................................................ 60

Troubleshooting............................................................... 61

Product Specifications..................................................... 63

Dimensions...................................................................... 64

INTRODUCTION

Introduction

INTRODUCTION

Package Contents

Open the package and ensure that you have the following items:

Optional accessories

If anything is missing or appears damaged, contact your dealer immediately.

Remote control Two “AAA” size batteries Power cord(By country)

Ring cap cover set Quick Guide Operation manual (this manual)

HD 15-pin VGA to HD 15-pin VGA cable

RS-232C cable (3M)

DVI-D to DVI-D cable (3M)

DVI-D to HDMI cable (3M)

Ceiling mount package

Note •Some of the cables may not be available depending on the region. Please check with

your nearest Authorized Dealer.

COMPONENT1

COMPONENT2

VIDEO/S-VIDEO

DVI/PC

MatterhornDLPFRONTPROJECTOR

Quick Guide

©Allrightsreserved.

Thismanualmaynotbecopiedinanymediaorformwithoutthewrittenconsentofthemanufacturer.

User's Manual

INTRODUCTION

Features

• Newly developed 0.65-inch DMD™ chip provides significantly improved optical efficiency and

excellent contrast ratio.

• Newly developed LVDS (Low voltage differential signal) chip eliminates Color Breaking phe-

nomena common with previous generation DLP™ projectors.

• Use of high-output lamp realizes both high color purity and high brightness. Natural images

made possible by high color reproducibility can be created with high-brightness, powerful

expression capabilities.

• Realizes vivid images using the latest image quality circuitry.

• New I/P conversion algorithm enhances the performance of the motion detect I/P conversion.

• Extensive improvements on the jagged edges or slanted lines in moving images.

• New Edge Up-Scaling.

• As a result of reducing jagged edges and flickering when up-scaling edges of slanted lines,

even signals not reaching a panel resolution of 480I/P can be projected by converting them to

1280X720 resolution images.

• New Film Mode Function.

• 3:2 pull down enhancement for not only 480I and 576I signals, but HDTV 1080I signals as well.

• White balance.

• Use of a DVI/HDCP terminal enables all processes from input to signal processing and projec-

tion to be performed digitally, resulting in the realization of all-digital projection without any

data loss due to analog conversion. This also supports the building of home theaters using

HTPC.

INTRODUCTION

Components

Projector (Front and Top View)

Temperature indicator

The projector has an over temperature warning LED on the control panel. If the projector overheats because

of a dirty filter or another problem, the LED will flash, and the projector lamp will turn off, after which a 90-

second cooling off period occurs. After restarting the projector, if the unit doesn’t operate normally, take the

projector in for servicing.

STATUS

EXIT

INPUT

ECO

ENTER

Focus

Zoom

LENS SHIFT (H)

LENS SHIFT (V)

ENTER button

For setting the selected items

or adjustments from the menu.

Zoom ring

Adjust screen display

Focus ring

Adjust focus.

Adjustment foot

Power (ON/OFF) buttons

For turning the power on or off.

Intake vent

Adjustment foot

Remote control sensor

Exhaust vent

Adjustment buttons

(T,S,W,X)

For selecting menu items.

Temperature indicator

This indicator glows red, when

the temperature of the projector

exceeds the set critical

temperature or when the fan

functions abnormally.

MENU button

Press this button to enter

the OSD menus.

INPUT button

Press this button to select

the input source.

ECO button

For power saving/

extended lamp life.

Exit button

For exiting the OSD.

Lens shift dial

(Horizontal)

Lens shift dial

(Vertical)

Power indicator

Blue:

The power is ready.

Blue blinking:

The fan is

cooling.

Ring cap cover set

Prevent foreign objects from

falling into the focus/zoom ring

compartment.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Liesegang Projektor Handbücher

Liesegang

Liesegang 294 Bedienungsanleitung

Liesegang

Liesegang ddv 1800 Bedienungsanleitung

Liesegang

Liesegang 266 Bedienungsanleitung

Liesegang

Liesegang dv350 Bedienungsanleitung

Liesegang

Liesegang ddv 1500 Bedienungsanleitung

Liesegang

Liesegang 278 Bedienungsanleitung

Liesegang

Liesegang ddv 2300 Bedienungsanleitung

Liesegang

Liesegang dv-485 Handbuch

Liesegang

Liesegang dv 420 Bedienungsanleitung

Liesegang

Liesegang dv475 Bedienungsanleitung

Liesegang

Liesegang ddv 1111 Bedienungsanleitung

Liesegang

Liesegang dv370 Bedienungsanleitung

Liesegang

Liesegang dv335 Bedienungsanleitung

Liesegang

Liesegang 251 Bedienungsanleitung

Liesegang

Liesegang ddv 2500 Bedienungsanleitung

Liesegang

Liesegang dv 465 Bedienungsanleitung

Liesegang

Liesegang ddv 3200 Gebrauchsanweisung

Liesegang

Liesegang Solid Cinema 215 Bedienungsanleitung

Liesegang

Liesegang dv 420 Bedienungsanleitung

Liesegang

Liesegang DV 390 Bedienungsanleitung

Liesegang

Liesegang dv 481 Handbuch

Liesegang

Liesegang ddv 2500 Bedienungsanleitung

Liesegang

Liesegang DV610 Bedienungsanleitung

Liesegang

Liesegang Solid Ultra Technisches Dokument

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Liesegang e-motion4100 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken