Lifetime COMPETITION Series XL POWER LIFT 71525 Kurzanleitung

**U.S. and Canada customers ONLY**

IF ASSISTANCE IS NEEDED,

DO NOT CONTACT THE STORE!

CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) 225-3865

HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)

**Call or visit our Web site for Saturday hours**

**For customers outside the U.S. or Canada, please contact the store for assistance.**

3/31/2012

COMPETITION SERIES XL POWER LIFT®

BASKETBALL SYSTEM

MODEL #71525

ASSEMBLY INSTRUCTIONS AND OWNER’S MANUAL

Save this instruction in the event that the manufacturer has to be contacted for replacement parts.

WARNING

Failure to comply with any of the warnings

in these instructions may result in serious

personal injuries such as cuts, broken bones,

nerve damage, paralysis, brain injury, or

death. Failure to comply may also result in

property damage. Please heed all warnings

and cautions. To ensure your safety, do not

attempt to assemble this system without

reading and following all instructions carefully.

Identify and inventory the parts using the

Parts List.

INSTRUCTION #1039811 D

**A MINIMUM OF TWO ADULTS ARE REQUIRED FOR

ASSEMBLY**

www.lifetime.com

COPY

PARTS LIST

ID Part # Description Qty

TP 1030700 Top Pole 1

MP 1030701 Middle Pole 1

BP 1030859 Bottom Pole 1

AB DD00800 Net 1

AC 502027H Handle 1

AD 502049G Trigger 1

AE 1030667 Extension Arm (Long) 2

AA 1030669 Extension Arm (Short) 2

AF 502056 Plastic Guard 1

AK CA00885 Zip Tie 2

AL 604084 Height Sticker 1

AM 1030660 Spring Bracket 1

AN HA00800 Gas Spring 1

AO 825619 Rim 1

AP 1030781 Backboard Bracket Right 1

AQ 1030762 Backboard Bracket Left 1

AR 1030758 Rear Lifter Arm 2

AS ZA10185 Bellows 1

AU 1030727 Backboard 1

AW 500096 Pole Cap 1

AX 1021852 Rim Cover Plate 1

FL CA00299 Left Frame Pad 1

FR CA00399 Right Frame Pad 1

FB CA00999 Bottom Frame Pad 2

FM FS16500 Sticker, Warning (Applied) 1

AJ 700506 Wood Block 1

Rim Hardware (1013678)

RA BS01000 #7 x 3/8” Screw 4

RB 300104 3/8” Push Nut 2

RC 300106 5/16” x 2” Carriage Bolt 2

RD 300128 Jam Nut 2

RE 302079 3 1/2” x 5” x 5/16” U-Bolt 1

RF 302090 5/16” Nylock Flange Nut 4

RG 1001137 Compression Spring 2

RH 510038 3/8” x 5 1/2” Axle 1

RI 804018 Rim Pivot Bracket 1

RJ 804033 Spring Retainer Plate 1

Pole Joint Hardware (1005748)

PA BS02000 1/4” x 3/4” Screw 2

PB 1004620 Self-Tapping Screw 2

Frame Pad Hardware (HH00700)

FA BS00100 #10 x 3/4” Self-Drilling Screw 10

Tools and Materials Required for Assembly

(Not Included)

1. Adjustable Wrench

2. Phillips Screwdriver

3. 1/2” Wrenches (2)

4. 9/16” Wrenches (2)

5. 3/4” Wrenches (2)

6. 11/16” Wrench

7. Hammer or Mallet

8. 90 lb. Concrete Mix Bags (6)

HARDWARE IS ACTUAL SIZE

(Unless otherwise indicated)

9. Tape Measure

10. Punch/Dowel or similar tool

11. Pliers

12. Scissors/Wire Cutters

13. Scrap Wood or Cardboard

14. Electric Drill

15. 1/2” Socket Wrench

16. 1/2” x 3’ Rebar

RCRA RD RF

(Not actual size)

BEFORE BEGINNING ASSEMBLY

A. Identify and inventory all parts using the checklist boxes on the Parts List. Keep the

hardware bags and their contents separate. If any parts are missing, call our Customer

Service Department.

B. Test ﬁt all Bolts by inserting them into their respective holes. If necessary, carefully

scrape away any excess powder coating buildup from inside the holes. Do not scrape

away all of the powder coating. Bare metal may rust. You may need to pound some

Bolts into place with a hammer or mallet.

PA FA

COPY

ID Part # Description Qty

Handle Hardware (1017923)

HA 302007 3/8” x 6 1/2” Hex Bolt 2

HB 300101 Release Pin 1

HC 302008 3/8” Centerlock Nut 2

HD 300187 1/2” x 6 1/2” Hex Bolt 1

MH 301008 1/2” Centerlock Nut 1

Main Hardware (1039829)

MA 300029 1/2” x 7 1/8” Hex Bolt 5

MB 300022 1/4” Centerlock Nut 2

MC 1028047 .38” x 1” Steel Spacer 2

MD 300043 Cotter Pin 1

ME 300055 1 1/2” Metal Pin 1

MH 301008 1/2” Centerlock Nut 5

MI 300110 1/4” x 2 3/4” Hex Bolt 2

MJ 302053 3/8” x 4” Hex Bolt 2

ML 800324 1/2” x 2.31 Steel Spacer 2

MN 500032 1/2” x 1/8” Spacer 4

MO 500015 3/8” x 1/2” Handle Spacer 2

MQ 500081 Grease Packet 1

MR 800331 .62” x .706” x 3.20” Spacer 1

MT 800239 1/2” x 3.41” Spacer 2

MX 302011 5/16” x 1 1/4” Carriage Bolt 2

MY 302090 5/16” Nylock Flange Nut 2

MZ 500013 .69 x .592 Black Spacer 4

BC 300031 3/8” Flat Washer 2

HC 302008 3/8” Centerlock Nut 2

PARTS LIST MA

(Not actual size)

HARDWARE IS ACTUAL SIZE

(Unless otherwise indicated)

(Not actual

size)

Thread lengths may vary

POLE SECTION IDENTIFICATION

Identify the pole sections before beginning assembly. Failure to assemble the pole sections

correctly may result in severe personal injury or property damage as described on Page One.

ONCE THE POLE SECTIONS HAVE BEEN SEATED, THEY CANNOT BE SEPARATED.

TP MP BP

Top Pole:

Four holes at the top of

the pole, four holes in

the middle, two holes

near the bottom and

one small hole at the

bottom.

Middle Pole:

One slot at the top of

the pole and one small

hole at the bottom.

Warning Sticker.

Bottom Pole:

One slot at the top of the

pole and a bent edge

at the bottom. Shortest

pole.

SAFETY INSTRUCTIONS

Most injuries are caused by misuse and/or not following instructions. Use caution when using

this system.

Owner must ensure that all players know and follow these rules for safe operation of the system.

To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check

entire box and inside all packing material for parts and/or additional instruction material. Before beginning

assembly, read the instructions and identify parts using the hardware identiﬁer and parts list in this document.

Proper and complete assembly, use and supervision are essential for proper orientation and to reduce the risk

of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and

operated properly.

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID

WARRANTY.

t*GVTJOHBMBEEFSEVSJOHBTTFNCMZVTFFYUSFNFDBVUJPO

t5ISFFDBQBCMFBEVMUTBSFSFDPNNFOEFEGPSUIJTPQFSBUJPO

t"TTFNCMFUIFQPMFTFDUJPOTQSPQFSMZ'BJMVSFUPEPTPDPVMEDBVTFUIFQPMFTFDUJPOT

to separate during play.

t#FGPSFEJHHJOHDPOUBDUVUJMJUZDPNQBOZUPMPDBUFVOEFSHSPVOEQPXFSDBCMFTHBT

and water lines. Ensure that there are no overhead power lines within 20 ft. (7m)

radius of pole location.

t.JOJNVNPQFSBUJPOBMIFJHIUJTwNUPUIFSJN

Maintaining your privacy is our long-standing policy at Lifetime. And you can rest assured that

Lifetime will not sell or provide your personal data to other third parties, or allow them to use your

personal data for their own purposes.

We invite you to read our privacy policy at www.lifetime.com

At Lifetime, we are committed to providing innovative and quality products. While registering, you

will have the opportunity to give us your feedback. Your input is valuable to us.

You can also opt-in to receive new product notiﬁcations or promotions.

In the unlikely event of a product recall or safety modiﬁcation, your registration provides the infor-

mation we need to notify you directly.

Registration is fast, easy, and completely voluntary.

For a nonpermanent installation of your basketball system, a Ground Sleeve provides an alternative to

cementing the pole into the ground. See Page 14 for more information.

24”

18”

14.5”

11.1 Dig a round hole 24” deep and

18” in diameter. The edge of the hole

should be ﬂush with the edge of the playing

surface.

1.2 Make a mark 14.5” up from

the dimpled end of the Bottom Pole

(BP) (do not scratch the powder

coating).

22.1 Mix 5 1/2 bags of concrete, following the directions on the concrete bags.

Keep in mind that a thicker mix of concrete will dry stronger.

2.2 Fill the hole to the top with concrete.

2.3 Insert the dimpled end of the Bottom Pole into

the cement up to the 14.5” mark and 4” away

from the playing surface.

Warning: If the pole is buried too deep or too shallow, the

Rim will not be at the correct height.

Note: Form the cement into a downward slope away from

the pole to allow water runoff. Failure to do so may result in

premature rusting of the pole.

Important: Save a 1/2 bag of concrete mix to use later in the assembly.

3.1 The slots in the Bottom Pole must be parallel

to the playing surface. If necessary, insert a straight

object (a ruler, wire, etc.) through the slots in the Bottom

Pole. Rotate the pole until the straight object is parallel to

the playing surface.

44.1 Place the 1/2” x 3’ rebar (not included) inside the Bottom Pole (BP).

4.2 Check the pole several times within the ﬁrst hour to

make sure that all sides are vertical and that the pole does

not sink into the concrete. The 14.5” mark must remain

level with the playing surface.

Rebar

Important: Allow 1-4 hours for the concrete to set.

Important: Do not continue until the concrete has set for 1-4 hours.

55.1 Remove the straight object from the top of the pole.

5.2 Mix the remaining 1/2 bag of concrete and pour the concrete into

the Bottom Pole until it is just below the slots in the top of the pole.

Important: Do not overﬁll the pole, or you may not be able to assemble the rest

of the pole sections.

5.3 Tamp the concrete down in the Bottom Pole with a broom handle

to remove any air pockets.

5.4 Clean all excess concrete off the outside surface of the pole.

STOP!

The concrete must cure for at least 72 hours (3 days) before installing the rest of the

system. In humid climates or wet weather, allow additional time for the concrete to

cure. Do not proceed until the curing process is complete.

Playing

Surface

MJ MT

Small holes Large

holes

Required For This Page:

9/16” Wrenches

(2)

(2) (2)

MJ AM HCMTBC

BC (2)

1039829

Screwriver TP

6.1 Completely tighten the Nuts.

(1)

1005748

WARNING

The poles must be seated together!! Even if the poles cover the slots

before seating, you must strike them on the wood ﬁve to six times!! Failure

to seat the poles correctly could allow the poles to separate during use,

which could lead to serious personal injuries or property damage as

listed on Page One.

This step cannot be reversed.

Warning: If the Top and Middle Poles do not completely cover

the slots on the Middle and Bottom Poles after seating, DO NOT

COMPLETE ASSEMBLY. Call our Customer Service Department.

9.1 Strike each end of the Pole ﬁrmly 5 to 6 times on a piece of

scrap wood or cardboard.

Warning: Do not hit your feet with the pole sections, as

serious injury could occur.

Note: The Screw will spin freely once

installed.

8.2 Insert a 1/4” x 3/4” Screw (PA)

through the small hole in the Top Pole

and into the Middle Pole.

8.1 Align the hole in the Top Pole with the

slot in the Middle Pole and slide the Top

Pole over the Middle Pole.

Do not jam the poles together until instructed.

7.1 Apply the Height Sticker (AL) so it wraps

around the opposite side of the pole as the

Spring Bracket (AM).

Note: The small notch in the Sticker

ﬁts around the hole in the pole.

Note: There are two screw holes at the

bottom of the pole. The correct hole will be

slightly larger and slightly lower on the pole.

Zip Tie (AK)

Larger End

10.2 Use pliers to tighten the Zip Ties (AK) securely. Cut off the ends of the Zip Ties.

Zip Tie (AK)

10.1 The bottom of the Bellows (AS) overlaps the Gas Spring (AN) by 1”. The

top is 1/2” from the top of the Spring.

Required For This Page:

9/16” Wrenches

Scissors/

Wire Cutters/

Pliers

11.2 Tighten the Nut until it is ﬂush with the Bolt.

11 11.1 Line up the Rear Lifter Arms

(AR) with the Gas Spring (AN).

AR AR

AC HD

1017923 HD (1)

3/4” Wrenches

(1)

Hammer/

Mallet

12.1 Use pliers to bend the

Cotter Pin (MD) as shown

above.

13 13.1 Tighten the Nut until it is ﬂush with

the Bolt.

MD ME

14.1 Slide the Release Pin (HB)

through the oval holes of the clevis at

the end of the Gas Spring (AN).

15 15.1 The Release Pin (HB) should

ﬁt into the channels in the Trigger

(AD).

16 16.1 Tighten the Nut (HC) until it is

ﬂush with the Bolt.

1039829

AC HB

(2)

MO (2)

*(Not actual

size)

(1)*

HC (2)

(1)

1/2” Wrenches

Required For This Page:

Pliers

17.1 Hold the Backboard

Brackets (AP & AQ) together

and slide the U-Bolt (RE) through the

holes as shown.

17 18.1 Ensure the U-Bolt (RE)

is in the notches.

18.2 Completely tighten the Nuts

(MA).

18 19 19.1 Insert a 5/16” x 2”

Carriage Bolt (RC) through

each hole in the Rim Pivot Bracket

(RI).

20.1 Use the 1/2” socket

head from the socket head

wrench to press one Push Nut (RB)

onto one end of the Axle (RH).

RCRB

(Not actual size)

MB MI

9/16” Wrenches

1039829

1003678

(2)

(1)

(2) (2)

22 22.1 Lay the Backboard (AU) on a table or bench.

Note: The U-Bolt (RE) goes

through the top holes in the

Backboard.

21.1 Slide the end of the Axle (RH) through the Rim (AO) and the

Rim Pivot Bracket (RI). Press the Push Nut (RB) onto the end

of the Axle. Use the 1/2” socket head to secure the Push Nut if

needed.

Note: The Push Nut should rest about

1/4” from the end of the Axle. If the

Push Nut slips on too far, continue

sliding it to the other end of the Axle to

remove it and try again.

1/2” Socket Wrench

Required For This Page:

1/2” Wrench

Electric Drill/

Screwdriver

25.1 Place the Spring Retainer Plate

(RJ) and secure with Nylock Flange

Nuts (RF).

(Not actual

size)

(1)

(4)

3/4” Wrenches

24.1 Place the Compression

Springs (RG) over the ends of

the U-Bolt (RE).

MX MX

26.1 Slide a Carriage Bolt (MX) into the crimped slot in each

Backboard channel.

27.1 Attach the Rim Cover Plate (AX) to the Rim using #7

x 3/8” Screws (RA).

1003678

(4)

Note: Do not overtighten the Nuts

(RF).

Only hand

tighten the

Nylock Flange

Nuts (RG).

23.1: Slide a Spacer (MC) over each Tap Bolt (RC) between

the Backboard and the Backboard Brackets.

(2)

1039829

31.1 Rest the Backboard (AU) and Rim (AO) on cardboard

to prevent scratching.

29.1 Tighten the Nut until it is ﬂush with the Bolt.

30.1 Attach this end of the Long Extension Arms (AE) to the Backboard

Brackets (AP & AQ).

30.2 Tighten the Nut until it is ﬂush with the Bolt.

MH MZ MA

(2)

(4)

Required For This Page:

1/2” Wrench

3/4” Wrenches

1039829

28.1 Bend the Backboard Brackets (AP & AQ) out

and over the Carriage Bolt (MX).

28.3 Completely tighten all Rim

hardware.

Note: Do not overtighten the Nuts (MY).

Note: The lower holes

should go over the Carriage

Bolts.

28.2 Secure Brackets with 5/16 “

Nylock Flange Nuts (MY).

(2)

Andere Handbücher für COMPETITION Series XL POWER LIFT 71525

Andere Lifetime Sport & Outdoor Handbücher

Lifetime

Lifetime POWER LIFT 91002 Bedienungsanleitung

Lifetime

Lifetime SPEED SHIFT 51550 Bedienungsanleitung

Lifetime

Lifetime ACTION GRIP 71799 Bedienungsanleitung

Lifetime

Lifetime POWER LIFT 90878 Bedienungsanleitung

Lifetime

Lifetime 90086 Bedienungsanleitung

Lifetime

Lifetime POOLSIDE 90742 Bedienungsanleitung

Lifetime

Lifetime ACTION GRIP 90853 Bedienungsanleitung

Lifetime

Lifetime PORTABLE PROCOURT 90688 Bedienungsanleitung

Lifetime

Lifetime POWER LIFT 90757 Bedienungsanleitung

Lifetime

Lifetime 60429 Bedienungsanleitung

Lifetime

Lifetime QUICK ADJUST 1531 Bedienungsanleitung

Lifetime

Lifetime STREAMLINE 90114 Bedienungsanleitung

Lifetime

Lifetime 51550 Bedienungsanleitung

Lifetime

Lifetime COMPETITION Series XL POWER LIFT 71525 Bedienungsanleitung

Lifetime

Lifetime 90056 Bedienungsanleitung

Lifetime

Lifetime DOUBLE SHOT 90648 Bedienungsanleitung

Lifetime

Lifetime POWER LIFT 90231 Bedienungsanleitung

Lifetime

Lifetime QUICK ADJUST 1008 Bedienungsanleitung

Lifetime

Lifetime STREAMLINE 90588 Bedienungsanleitung

Lifetime

Lifetime 1221 Bedienungsanleitung

Lifetime

Lifetime QUICK ADJUST 1044 Bedienungsanleitung

Lifetime

Lifetime ACTION GRIP 91330 Bedienungsanleitung

Lifetime

Lifetime CRANK ADJUST 90568 Bedienungsanleitung

Lifetime

Lifetime PROCOURT 90073 Bedienungsanleitung

Beliebte Sport & Outdoor Handbücher anderer Marken

Flybar

Flybar POGO TRICK BOARD Bedienungsanleitung

Crivit

Crivit 93713 Bedienungsanleitung

Hudora

Hudora 76171 Montageanleitung

Axler

Axler GSU-1 Bedienungsanleitung

Aquaglide

Aquaglide FREEFALL 6 LANDING PAD Bedienungsanleitung

Cap Strength

Cap Strength POWER RACK FM-CS7000F Bedienungsanleitung

La Sportiva

La Sportiva RACE BORG Bedienungsanleitung

Crivit

Crivit 302640 Bedienungsanleitung

Sportime

Sportime Equalizer Bedienungsanleitung

T&R Sports

T&R Sports 5FT FOOSBALL TABLE Bedienungsanleitung

Salewa

Salewa VERT Bedienungsanleitung

KICK

KICK Decagon Bedienungsanleitung

byox

byox FJ-4.5FT Bedienungsanleitung

CHINESPORT Spa

CHINESPORT Spa 01325 Bedienungsanleitung

AXI.COM

AXI.COM ConesPro101 Bedienungsanleitung

Insportline

Insportline IN 2052 Bedienungsanleitung

Rugged Interactive

Rugged Interactive CardioWall Compact Kurzanleitung

N-FLATABLES

N-FLATABLES Belly Bouncer Fire Dog Bedienungsanleitung