Lightspeed RedcatAccess Bedienungsanleitung
Quick Start Guide
Instructional Audio System
Remove microphone
from charger. Press
the mute button to
unmute, hold near
your mouth and
begin speaking.
Remove microphone
from charger and press
the mute button to
begin speaking.
USING THE FLEXMIKE
PAIRING MICROPHONES TO REDCAT ACCESS
CHARGE MICROPHONES NIGHTLY
USING THE SHAREMIKE
ALIGN WITH
COLLARBONE
TALK (BLUE)
MUTE (WHITE)
TALK (BLUE)
MUTE (WHITE)
POWER/MUTE BUTTON
ADJUST
VOLUME
NORMAL OPERATION
CHARGING IN PROGRESS
CHARGING COMPLETE
POWER/MUTE
BUTTON
ADJUST
VOLUME
DETERMINE SET-UP LOCATION AND PLUG IN POWER SUPPLY
Redcat Access should be placed within 7 feet of an electrical outlet and on a
surface about 4-6 feet o the ground.
Next, find a location as far away as possible from the teacher who will be using
the microphone. Avoid putting Redcat in close proximity to the teacher’s mic
which can result in feedback.
Connect the AC power cord into the DC power supply. Insert the connector into
the Redcat and plug the power cord into an electrical outlet. Redcat Access
automatically powers on and the white POWER light on the front panel will glow.
POWER STATUS
LIGHT
Place the microphones
into the cradle charger. The
power status light will glow
red when it is charging.
When charging is complete,
the power status light will
glow green.
It takes about 5-6 hours
to fully charge the
microphone battery.
Your system is shipped with microphones and base units already paired.
If you ever need to pair new components, follow this pairing process.
REGISTER
AUDIO IN
DC OUTPUT
24V/1.75A
ON/OFF
MIN
MAX
AUDIO
(ALD) OUT
MIN
MAX
MIN
MAX
POWER ON
1
2
3
With a paperclip, push the register
button on the side of Redcat
Access.
From a powered o state, press and
hold the power button for 5 seconds
until the mic 1 and mic 2 lights start
flashing, then release the button and
let the pairing process finish.
The mic 1 or mic 2 lights on Redcat
Access will light green indicating
the pairing process is complete. The
corresponding mic 1 or mic 2 light on
the microphone will stay illuminated.
MIC 1 MIC 2
REGISTER
AUDIO IN
DC OUTPUT
24V/1.75A
ON/OFF
MIN
MAX
AUDIO
(ALD) OUT
MIN
MAX
MIN
MAX
1 2 3
MIC 2
MIC 1
POWER BUTTON
For complete operating instructions, go to www.lightspeed-tek.com/RCAN-usermanual (or scan the 2D barcode). QS0618US01-1
Quick Start Guide
DETERMINE LOCATION CONNECT TO POWER POWER ON
Connect the USB cable power cord
to a computer, or use the USB power
adapter to plug into wall outlet.
Plug the USB cable into the USB input
on the back of the Media Connector.
Media Connector is designed to be
connected to the primary media
source in the classroom, usually the
computer or display panel.
When powered on, the white LED on the front
panel will glow.
Redcat does not need to be powered o at the
end of day, but if desired, you may power down
Redcat by powering down the Media Connector.
Audio
InputAudio
OutputTone
Level
Push
StatusPower
Media
Media
Connector
Connector
Audio
InputAudio
OutputTone
Level
Push
StatusPower
Media
Media
Connector
Connector
POWER LIGHT
OR
USING FLEXMIKE AS A WIRELESS AUDIO LINK
CONNECTING TO AN ANALOG AUDIO SOURCE
Audio
InputAudio
OutputTone
Level
Push
StatusPower
Media
Media
Connector
Connector
AUDIO INPUT SELECTORLEVEL
You can connect a 2nd microphone to your computer’s USB port to
enable a wireless 2-way audio link.
SEND AUDIO FROM THE COMPUTER to the Redcat to ensure all
audio from the computer (videos, video conferencing, audiobooks,
music, etc) can be played through Redcat Access.
SEND AUDIO TO THE COMPUTER from the Redcat Access to ensure
the teacher’s Flexmike and any student microphones are clearly
picked up by a video conferencing solution.
Plug your external audio equipment (computer, tablet, video display,
etc.) into one of the Audio input jacks using a 3.5mm audio cable.
Adjust the volume by pressing the Audio Input selector and adjusting
the level knob.
USB
5V / 0.2A
Audio Inputs
432
1
Audio Outputs
2
1
.MM CABLE
1 2 3
Redcat Access with optional Media Connector
Audio
Input Audio
Output Tone
Level
Push
StatusPower
Media
Media
Connector
Connector
Audio
Input Audio
Output Tone
Level
Push
StatusPower
Media
Media
Connector
Connector
Connect the microphone to
your computer using a USB-C
cable. Open your computer
sound settings to select
Lightspeed Audio as the
microphone and speaker.
USB cable sold separately. Lightspeed oers
a USB-A to USB-C cable for sale (part #USBC)
Media Connector
Andere Lightspeed Stereoanlage Handbücher
Lightspeed
Lightspeed flexcat Bedienungsanleitung
Lightspeed
Lightspeed Cat 885 Bedienungsanleitung
Lightspeed
Lightspeed 975 Bedienungsanleitung
Lightspeed
Lightspeed Redcat media Bedienungsanleitung
Lightspeed
Lightspeed 820iR Bedienungsanleitung
Lightspeed
Lightspeed 705iR Bedienungsanleitung
Lightspeed
Lightspeed TOPCAT Bedienungsanleitung
Lightspeed
Lightspeed Access Link Bedienungsanleitung
Lightspeed
Lightspeed TOPCAT Bedienungsanleitung
Lightspeed
Lightspeed TOPCAT Bedienungsanleitung
Lightspeed
Lightspeed 955 Access Bedienungsanleitung
Lightspeed
Lightspeed TOPCAT Bedienungsanleitung
Lightspeed
Lightspeed 820iR Bedienungsanleitung
Lightspeed
Lightspeed Redcat media Bedienungsanleitung
Lightspeed
Lightspeed TOPCAT Bedienungsanleitung
Lightspeed
Lightspeed 880iR Bedienungsanleitung
Lightspeed
Lightspeed Redcat media Bedienungsanleitung
Lightspeed
Lightspeed 955Access Bedienungsanleitung
Lightspeed
Lightspeed Mobile PA Bedienungsanleitung
Lightspeed
Lightspeed flexcat Bedienungsanleitung
