Linksys PAP2 Bedienungsanleitung
Linksys Sipura and PAP2 Analog Telephone
Adapter (ATA) - Installation Instructions
Below you will find installation instructions for the Linksys Sipura-200X or PAP2 broadband phone
adapter.
Setting up your Linksys ATA to work with KO TACT+ phone network is easy! The following
instructions will help you set up your adaptor in a simple Step-by-Step method.
Introduction How does broadband phone work?
Step 1 Connect ATA to your Broadband connection
Step 2 Verify & Configure your IP address
Step 3 Prepare you device to work with phone network
Step 4 Complete the Setup-Wizard
Step 5 Start using your ATA with KONTACT+ phone network
Introduction: How should the broadband adaptor connect to your
network?
You must have a broadband Internet connection and the Linksys ATA. Since the adaptor works
independently of your computer, there are no requirements at all for your operating systems.
In some case you will not necessarily need a router if your cable modem has 2 Ethernet ports and supports
NAT.
Routers and Broadband service are not sold through KONTACT+ phone network. Routers are generally
available from most retail or online stores.
Please follow the following step-by-step guide below to setup your Linksys ATA to work with
KO TACT+ phone network Broadband Phone Service.
back to top
Step 1: Connect the Linksys ATA to your Broadband connection
Use this illustration of the back of the ATA to connect it to your network.
1. Phone 1 - plug your analog telephone cord in here to work with your KONTACT+ phone network
account
2. Ethernet Port - use an Ethernet cable to connect your ATA to your router or Internet connection
3. Power connection - Connect the power to your ATA
back to top
Step 2: Verify & Configure your IP address
A. At first we would need to verify that your ATA would acquire an IP automatically if your
network supports DHCP.
If you have purchased your Linksys ATA adaptor from KO TACT+ phone network you should
skip this section and proceed to section B.
If your network utilizes a DHCP Server to assign IP Addresses to network devices, or if you are
connecting the ATA to a home router such as a Linksys or Netgear router, please do the following
1. Pick up the phone connected to Phone 1 of the ATA and enter "* * * *". You will hear a voice
prompt saying "Linksys configuration menu.".
2. Press the keys 1 0 1 # on your analog phone.
3. Then press 1 # to enable DHCP.
4. Then press 1 to save your configuration settings. Hang up the phone and wait for a couple of
minutes.
B. ext, we would need to verify that your ATA has a valid IP Address, Please be prepared with
pen and paper and proceed with the following:
1. Pick up the phone connected to Phone 1 of the ATA and enter "* * * *". You will hear a voice
prompt saying "Linksys configuration menu".
2. Press the keys 1 1 0 # on your analog phone. The system will now read back the IP address of
your ATA. Please write it down.
If the IP is 0.0.0.0, your ATA does not have a valid IP address. In this case you need to:
1. Hang up the phone, unplug and re-plug your ATA power cord.
2. Wait 2 minutes, and check the IP again.
3. If you still get 0.0.0.0, there can be three reasons for this
a. Your DHCP Server is not assigning an IP address to the ATA (in which case you should
contact your network administrator or ISP for assistance).
b. Your network does not have a DHCP server (in which case you should proceed to
configuring your IP manually using a Static IP configuration).
For instruction how to manually configure your static IP click here.
c. You have bought a Static IP (in which case you should proceed to configuring your IP
manually using a Static IP configuration).
For instruction how to manually configure your static IP click here.
back to top
Step 3: Prepare you device to work with phone network
If you have purchased your Linksys ATA adaptor from KO TACT+ phone network you should
skip this step and proceed to Step 4.
1. Open your configuration page. To do so, type the following into your web browser
http //aaa.bbb.ccc.ddd/admin/advanced where "aaa.bbb.ccc.ddd" represents the IP address of your
ATA.
2. Then, on your ATA configuration page, make the necessary changes to the following fields so
they contain the values indicated below. (Please note that your configuration page may not contain
all of the fields that are listed. Make sure to update the fields that you do have on your
configuration page as outlined.)
3. Under the "line 1" tab
1- Type the Sip proxy IP (208.89.105.21) address and proxy port (5060 and 7060)
2- Display Name, UserID, AuthID should be your Account ID on Portasip
3- Password should be your password on portasip
4- Use AuthID should be set to YES
5- Click on Save Settings
back to top
Appendix 1. IVR menu
Please use the table below for options and responses to the information you may use to configure your
LINKSYS ATA
Action Menu Choice User Input Notes
Enter IVR Menu
* * * *
None
None. Ignore SIT or other tones
until you hear, “ inksys
configuration menu. Please enter
option followed by the pound key
or hang-up to exit.”
Check DHCP 100# None IVR will announce if DHCP in
enabled or disabled.
Enable/Disable DHCP 101# Enter 1 to enable
Enter 0 to disable
Check IP Address 110# None IVR will announce current IP
Address of PAP2
Set Static IP Address
111#
Enter IP address
using numbers on the
telephone key pad.
Use the *(star) key
when entering a
decimal point.
DHCP must be “Disabled”
otherwise you will hear, “Invalid
Option,” if you try to set this
value.
Check Network Mask 120# None IVR will announce the current
network mask of PAP2.
Set Network Mask
121#
Enter value using
numbers on the
telephone key pad.
Use the * (star) key
when entering a
decimal point.
DHCP must be “Disabled”
otherwise you will hear, “Invalid
Option,” if you try to set this
value.
Check Static Gateway
IP Address 130# None IVR will announce the current
gateway IP address of PAP2.
Set Static Gateway IP
Address
131#
Enter IP address
using numbers on the
telephone key pad.
Use the *(star) key
when entering a
decimal point.
DHCP must be “Disabled”
otherwise you will hear, “Invalid
Option,” if you try to set this
value.
Appendix 2. Router configuration.
To connect your ATA to our service your router must have opened UDP ports.
In case you use "Port forwarding" mode to your ATA LAN IP, you must forward UDP ports
5060,5061,5062,7060 - Sip signalling
16384-16482 - Media Ports
In case you use "NAT" mode , please open the UDP ports range 1845-50000
Please refer your router vendor documentation, for example for DL-514 DL-514 *
After you device connected to our network with your accounts,
ATA user password will be the same as on the line1 account,
ATA admin password will be the same as for line2 account.
Andere Handbücher für PAP2
14
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Linksys Adapter Handbücher
Linksys
Linksys WPC55AG Original Betriebsanleitung
Linksys
Linksys Instant Broadband Series Bedienungsanleitung
Linksys
Linksys Instant PowerLine PLUSB10 Original Betriebsanleitung
Linksys
Linksys WUSB600N (EU) Bedienungsanleitung
Linksys
Linksys Instant Broadband Series Bedienungsanleitung
Linksys
Linksys LNE100M Original Betriebsanleitung
Linksys
Linksys WPC200 Bedienungsanleitung
Linksys
Linksys PAP2-NA Kurzanleitung
Linksys
Linksys WUSB11 ver. 2.6 Bedienungsanleitung
Linksys
Linksys WPC4400N Bedienungsanleitung
Linksys
Linksys USB3GIG Bedienungsanleitung
Linksys
Linksys HU200 Bedienungsanleitung
Linksys
Linksys PLE200 - PowerLine AV EN Adapter Bridge Bedienungsanleitung
Linksys
Linksys USB10T Bedienungsanleitung
Linksys
Linksys WUSB6100M Bedienungsanleitung
Linksys
Linksys Fax Adapter Bedienungsanleitung
Linksys
Linksys WPC200 Original Betriebsanleitung
Linksys
Linksys WUSB11 ver. 2.6 Original Betriebsanleitung
Linksys
Linksys WUSB54GC EU Bedienungsanleitung
Linksys
Linksys Linksys SPA9000 Bedienungsanleitung
