Linksys WAPPOE12 Bedienungsanleitung
A Division of Cisco Systems, Inc.
®
WIRED
Model No.
WAPPOE12
Adapter Kit
12 Volt Power Over Ethernet
User Guide
12 Volt Power Over Ethernet Adapter Kit
Copyright and Trademarks
Specifications are subject to change without notice.Linksys is a registered trademark or trademark of Cisco Systems,
Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2004 Cisco Systems, Inc. All rights
reserved. Other brands and product names are trademarks or registered trademarks of their respective holders.
How to Use this Guide
Your guide to the 12 Volt Power Over Ethernet Adapter Kit has been designed to make understanding networking
with the Power Over Ethernet Adapter Kit easier than ever. Look for the following items when reading this Guide:
In addition to these symbols, there are definitions for technical terms that are presented like this:
Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like
this:
Figure numbers and descriptions can also be found in the “List of Figures” section.
This exclamation point means there is a caution or warning and is something
that could damage your property or Power Over Ethernet Adapter Kit.
This question mark provides you with a reminder about something you
might need to do while using the Power Over Ethernet Adapter Kit.
This checkmark means there is a note of interest and is something you should
pay special attention to while using the Power Over Ethernet Adapter Kit.
word: definition.
Figure 0-1: Sample Figure Description
WAPPOE12-UG-41105NC JL
WARNING: This product contains chemicals, including lead, known to the State of California to cause
cancer, and birth defects or other reproductive harm. Wash hands after handling.
12 Volt Power Over Ethernet Adapter Kit
Table of Contents
Chapter 1: Introduction 1
Welcome 1
What’s in this Guide? 3
Chapter 2: Getting to Know the 12 Volt Power Over Ethernet Adapter Kit 5
Overview 5
The Injector 5
The Splitter 7
Chapter 3: Connecting the 12 Volt Power Over Ethernet Adapter Kit 9
Overview 9
Powering on a Device that Uses a Standard Power Adapter 10
Powering on a Device that Uses Inline Power 12
Appendix A: Glossary 13
Appendix B: Specifications 21
Appendix C: Warranty Information 23
Appendix D: Regulatory Information 25
Appendix E: Contact Information 27
12 Volt Power Over Ethernet Adapter Kit
List of Figures
Figure 2-1: Injector’s First Side Panel 5
Figure 2-2: Injector’s Second Side Panel 6
Figure 2-3: Injector’s LED 6
Figure 2-4: Splitter’s First Side Panel 7
Figure 2-5: Splitter’s Second Side Panel 7
Figure 2-6: Splitter’s LED 8
Figure 3-1: Power Over Ethernet Kit Used with a Switch and Access Point 9
Figure 3-2: Connect the Ethernet Cable to the Injector 10
Figure 3-3: Connect the Ethernet Cable to the Splitter 10
Figure 3-4: Barrel Jack Adapter (optional) 11
Figure 3-5: Connect Power to the Injector 11
Figure 3-6: Connect the Ethernet Cable to the Injector 12
Figure 3-7: Connect Power to the Injector 12
12 Volt Power Over Ethernet Adapter Kit
1
Chapter 1: Introduction
Welcome
Chapter 1: Introduction
Welcome
Thank you for choosing the Linksys 12 Volt Power Over Ethernet Adapter Kit. It will let you put your wireless
access point or other network device almost anywhere, by eliminating the need for a nearby electrical outlet.
The best place for an access point is usually on the ceiling, in the center of the area that needs wireless
coverage, and the second best place would be high up on a wall. With the Power Over Ethernet Adapter Kit, you
don’t have to run power up to your access point.
How does the Power Over Ethernet Adapter Kit do this? It delivers power over a Category 5 Ethernet cable. The
PowerOver Ethernet AdapterKit includes two devices, the Injector andthe Splitter. The Injector sends power and
data over the Ethernet cable to the Splitter. Then the Splitter separates the data and power back into two cables
and delivers them to the remotely located access point—or other network device. The Injector can also be used
by itself with any Power Over Ethernet (POE)-enabled network device that accept 48 volts directly on a POE port.
Use the 12 Volt Power Over Ethernet Adapter Kit to send power and data to any Linksys product that requires a
12-volt power input. (If your Linksys product uses a 5-volt power input, then you should use the 5-volt kit, model
number: WAPPOE.)
Which Linksys products work with the 12 Volt Power Over Ethernet Adapter Kit? This is a list of the compatible
products, alphabetized by model number:
• ADSLMUE1 (all versions) - ADSL Modem with USB & Ethernet
• AG041 - ADSL Gateway with 4-Port Switch
ethernet: an IEEE standard network
protocol that specifies how data is
placed on and retrieved from a common
transmission medium.
access point: a device that allows
wireless-equipped computers and other
devices to communicate with a wired
network. Also used to expand the range
of a wireless network.
poe (power over ethernet): a technology
enabling an Ethernet network cable to
deliver both data and power.
NOTE: This list is subject to
change as Linksys
introduces new products.
12 Volt Power Over Ethernet Adapter Kit
2Chapter 1: Introduction
Welcome
• BEFCMU10 (all versions) - Cable Modem with USB and Ethernet Connections
• BEFCMUH4 - Cable Gateway
• BEFDSR41W - ADSL Gateway
• BEFSX41 (versions 1 and 2) - Broadband Firewall Router with 4-Port Switch/VPN Endpoint
• BEFW11S4 (version 4) - Wireless-B Broadband Router
• RT31P2 - Broadband Router with 2 PhonePorts
• WAG54G (versions 1.2 and 2) - Wireless-G ADSL Gateway
• WAP54G (version 2) - Wireless-G Access Point
• WCG200 (all versions) - Wireless-G Cable Gateway
• WGA54G - Wireless-G Game Adapter
• WPS54GU2 - Wireless-G PrintServer for USB 2.0
• WRK54G - Wireless-G Broadband Router
• WRT54G - Wireless-G Broadband Router
• WRT54GS - Wireless-G Broadband Router with SpeedBooster
• WRT54GP2- Wireless-G Broadband Router with 2 Phone Ports
Use the instructions in this User Guide to help you connect the Power Over Ethernet Adapter Kit. These
instructions should be all you need to get the most out of the Power Over Ethernet Adapter Kit.
12 Volt Power Over Ethernet Adapter Kit
3
Chapter 1: Introduction
What’s in this Guide?
What’s in this Guide?
This guide covers the steps for installing the Power Over Ethernet Adapter Kit.
• Chapter 1: Introduction
This chapter describes the Power Over Ethernet Adapter Kit’s application and this User Guide.
• Chapter 2: Getting to Know the 12 Volt Power Over Ethernet Adapter Kit
This chapter describes the physical features of the Power Over Ethernet Adapter Kit.
• Chapter 3: Connecting the 12 Volt Power Over Ethernet Adapter Kit
This chapter explains how to connect the Power Over Ethernet Adapter Kit to your network.
• Appendix A: Glossary
This appendix gives a brief glossary of terms frequently used in networking.
• Appendix B: Specifications
This appendix provides the technical specifications for the Power Over Ethernet Adapter Kit.
• Appendix C: Warranty Information
This appendix supplies the warranty information for the Power Over Ethernet Adapter Kit.
• Appendix D: Regulatory Information
This appendix supplies the regulatory information regarding the Power Over EthernetAdapter Kit.
• Appendix E: Contact Information
This appendix provides contact information for a variety ofLinksys resources, including Technical Support.
12 Volt Power Over Ethernet Adapter Kit
4Chapter 1: Introduction
What’s in this Guide?
12 Volt Power Over Ethernet Adapter Kit
5
Chapter 2: Getting to Know the 12 Volt Power Over Ethernet Adapter Kit
Overview
Chapter 2: Getting to Know the 12 Volt Power Over Ethernet
Adapter Kit
Overview
The Power Over Ethernet Adapter Kit iscomprised of two devices, the Injectorand Splitter. Use theKit so you can
move your access point, wireless bridge, or other network device to a remote location that is far from an
electrical outlet.
The Injector
The Injector’s built-in cable and ports are located on side panels.
The Injector’s First Side Panel
The Power & Data OUT port is located on the Injector’s first side panel.
Power & Data OUT This port allows you to connect the Injector to the Splitter or a network device that supports
inline power. (You will use the included Ethernet network cable to make this connection.) Figure 2-1: Injector’s First Side Panel
12 Volt Power Over Ethernet Adapter Kit
6Chapter 2: Getting to Know the 12 Volt Power Over Ethernet Adapter Kit
The Injector
The Injector’s Second Side Panel
The built-in Ethernet network cable and Power port are located on the Injector’s second side panel.
Ethernet IN The Injector has a built-in Ethernet network cable. You will connect this cable to one of the
Ethernet network ports on your router or switch.
Power The Power port is where you will connect the included adapter.
The Injector’s LED
The Power LED is located on the top of the Injector.
Power LED Green. The Power LED lights up when the Injector is powered on and ready for use.
Figure 2-2: Injector’s Second Side Panel
Figure 2-3: Injector’s LED
Andere Handbücher für WAPPOE12
1
Inhaltsverzeichnis
Andere Linksys Adapter Handbücher
Linksys
Linksys WPC54G EU Bedienungsanleitung
Linksys
Linksys WUSB200 Bedienungsanleitung
Linksys
Linksys WUSB600N (EU) Bedienungsanleitung
Linksys
Linksys WPC55AG Bedienungsanleitung
Linksys
Linksys Instant PowerLine PLUSB10 Bedienungsanleitung
Linksys
Linksys PAP2 Merkblatt
Linksys
Linksys WGA54AG Bedienungsanleitung
Linksys
Linksys WPC54GR (DE) Bedienungsanleitung
Linksys
Linksys WUSB11 ver. 2.6 Bedienungsanleitung
Linksys
Linksys WUSB11 ver. 2.6 Bedienungsanleitung
Linksys
Linksys WUSB11 ver. 2.6 Bedienungsanleitung
Linksys
Linksys PAP2 Bedienungsanleitung
Linksys
Linksys PAP2-VU Leitfaden
Linksys
Linksys SPA2002 Bedienungsanleitung
Linksys
Linksys WUSB54AG Original Betriebsanleitung
Linksys
Linksys WPC4400N Bedienungsanleitung
Linksys
Linksys Small Business SPA2102 Original Betriebsanleitung
Linksys
Linksys WGA11B Original Betriebsanleitung
Linksys
Linksys PCM1000 - Cisco 10/100/1000 CARDBUS MOBILE... Original Betriebsanleitung
Linksys
Linksys WMA11B - Wireless-B Media Adapter Original Betriebsanleitung
