Linksys EG1064 Bedienungsanleitung

A Division of Cisco Systems, Inc.

Model No.

WIRED Network Adapter

Gigabit

EG1064

User Guide

10/100/1000

10/100/1000 Gigabit Network Adapter

Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco

rights reserved. Other brands and product names are trademarks or registered trademarks of their respective

holders.

How to Use this Guide

Your guide to the Gigabit Network Adapter has been designed tomake understanding networking with the Gigabit

Network Adapter easier than ever. Look for the following items when reading this guide:

In addition to these symbols, there are definitions for technical terms that are presented like this:

Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like

this:

Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”.

This exclamation point means there is a Caution or

warning and is something that could damage your

property or the Gigabit Network Adapter.

word: definition.

This checkmark means there is a Note of interest and

is something you should pay special attention to while

using the Gigabit Network Adapter.

Thisquestionmark providesyou with a reminder about something

you might need to do while using the Gigabit Network Adapter.

Figure 0-1: Sample Figure Description

EG1064_V2-UG-31016NC JL

10/100/1000 Gigabit Network Adapter

Table of Contents

Chapter 1: Introduction 1

Welcome 1

What’s in this Guide? 1

Chapter 2: Getting to Know the 10/100/1000 Gigabit Network Adapter 3

Port and LEDs 3

Chapter 3: Installing the 10/100/1000 Gigabit Network Adapter in Your PC 4

Hardware Installation 4

Chapter 4: Installing the Driver for Windows XP 5

Overview 5

Instructions for Installing the Driver 5

Instructions for Uninstalling the Adapter 6

Chapter 5: Installing the Driver for Windows 2000 7

Overview 7

Instructions for Installing the Driver 7

Instructions for Uninstalling the Adapter 9

Chapter 6: Installing the Driver for Windows Millennium or 98SE 10

Overview 10

Instructions for Installing the Driver 10

Instructions for Uninstalling the Adapter 12

Chapter 7: Configuring the 10/100/1000 Gigabit Network Adapter in

Windows XP or 2000 13

Overview 13

Instructions for Accessing the Adapter’s Configuration 13

Adapter Configuration 13

Chapter 8: Configuring the 10/100/1000 Gigabit Network Adapter in

Windows Millennium or 98SE 16

Overview 16

Instructions for Accessing the Adapter’s Configuration 16

Adapter Configuration 16

Appendix A: Troubleshooting 19

Common Problems and Solutions 19

10/100/1000 Gigabit Network Adapter

Appendix B: Windows Help 23

Appendix C: Glossary 24

Appendix D: Specifications 30

Appendix E: Warranty Information 31

Appendix F: Regulatory Information 32

Appendix G: Contact Information 33

10/100/1000 Gigabit Network Adapter

List of Figures

Figure 2-1: Port and LEDs 3

Figure 3-1: Insert the Adapter into the PCI Slot 4

Figure 3-2: Set the Adapter Firmly in Place 4

Figure 3-3: Connect the Ethernet Network Cable 4

Figure 4-1: Welcome 5

Figure 4-2: Search This Location 5

Figure 4-3: Driver Installation Complete 5

Figure 4-4: Device Manager for Windows XP 6

Figure 4-5: Confirm Device Removal 6

Figure 5-1: Welcome 7

Figure 5-2: Install Hardware Device Drivers 7

Figure 5-3: Locate Driver Files 7

Figure 5-4: Driver Location 8

Figure 5-5: Driver Files Search Results 8

Figure 5-6: Driver Installation Complete 8

Figure 5-7: Computer Management for Windows 2000 9

Figure 5-8: Confirm Device Removal 9

Figure 6-1: Add New Hardware Wizard 10

Figure 6-2: Enter Location of Driver 10

Figure 6-3: Driver Files Search Results 10

Figure 6-4: Driver Installation Complete 11

Figure 6-5: Restart Computer 11

Figure 6-6: Device Manager for Windows Me or 98SE 12

Figure 6-7: Confirm Device Removal 12

Figure 6-8: System Settings Change 12

Figure 7-1: Device Manager for Windows XP or 2000 13

Figure 7-2: General Tab for Windows XP or 2000 13

Figure 7-3: Advanced Tab for Windows XP or 2000 14

10/100/1000 Gigabit Network Adapter

Figure 7-4: Driver Tab for Windows XP or 2000 14

Figure 7-5: Confirm Device Removal 14

Figure 7-6: Resources Tab for Windows XP or 2000 15

Figure 7-7: Power Management Tab for Windows XP or 2000 15

Figure 8-1: Device Manager for Windows Me or 98SE 16

Figure 8-2: General Tab for Windows Me or 98SE 16

Figure 8-3: Driver Tab for Windows Me or 98SE 17

Figure 8-4: Resources Tab for Windows Me or 98SE 17

Figure 8-5: Power Management Tab for Windows Me or 98SE 18

Chapter 1: Introduction

Welcome

10/100/1000 Gigabit Network Adapter

Chapter 1: Introduction

Welcome

Thank you for choosing the 10/100/1000 Gigabit Network Adapter. Built to run the fastest video, publishing, and

database network applications, the Gigabit Network Adapter is a high performance network adapter for PCI local

bus computers. Boasting an incredible maximum data throughput of 2000 megabits-per-second in full duplex

mode, it includes a 10BaseT/100BaseTX/1000BaseTX port, which means that you can begin integrating Gigabit

now—even if you don't plan on upgrading to a 1000Mbps network right away.

The Gigabit Network Adapter is Windows Plug-and-Play compatible. Wake-On-LAN support is built in—you can

wake up your workstations from anywhere on the network! Built-in support for the widest range of PCI mother-

boards, networking hardware, and software means you don't have to worry about compatibility.

Use the instructions in this Guide to help you install the Gigabit Network Adapter in your PC, install itsdriver, and

configure it. These instructions should be all you need to get the most out of the Gigabit Network Adapter.

What’s in this Guide?

This user guide covers the steps for installing the Adapter, installing its driver, and configuring it.

• Chapter 1: Introduction

This chapter describes the Adapter’s applications and this User Guide.

• Chapter 2: Getting to Know the 10/100/1000 Gigabit Network Adapter

This chapter describes the physical features of the Adapter.

• Chapter 3: Installing the 10/100/1000 Gigabit Network Adapter in Your PC

This chapter instructs you on how to install the Adapter inside your PC.

• Chapter 4: Installing the Driver for Windows XP

This chapter explains how to install the Windows XP driver for the Adapter.

• Chapter 5: Installing the Driver for Windows 2000

This chapter explains how to install the Windows 2000 driver for the Adapter.

• Chapter 6: Installing the Driver for Windows Millennium or 98SE

This chapter explains how to install the Windows Millennium or 98SE driver for the Adapter.

Full duplex: theabilityofanetworking

device to receive and transmit data

simultaneously.

Chapter 1: Introduction

What’s in this Guide?

10/100/1000 Gigabit Network Adapter

• Chapter 7: Configuring the 10/100/1000 Gigabit Network Adapter in Windows XP or 2000

This chapter instruct you on how to configure the Adapter in Windows XP or 2000.

• Chapter 8: Configuring the 10/100/1000 Gigabit Network Adapter in Windows Millennium or 98SE

This chapter instruct you on how to configure the Adapter in Windows Millennium or 98SE.

• Appendix A: Troubleshooting

This appendix describes some potential problems and solutions regarding use of the Adapter.

• Appendix B: Windows Help

This appendix describes how you can use Windows Help for instructions about networking, such as installing

the TCP/IP protocol.

• Appendix C: Glossary

This appendix gives a brief glossary of terms frequently used in networking.

• Appendix D: Specifications

This appendix provides the technical specifications for the Adapter.

• Appendix E: Warranty Information

This appendix supplies the warranty information for the Adapter.

• Appendix F: Regulatory Information

This appendix supplies the regulatory information regarding the Adapter.

• Appendix G: Contact Information

This appendix provides contact information for a variety of Linksys resources, including Technical Support.

Chapter 2: Getting to Know the 10/100/1000 Gigabit Network Adapter

Port and LEDs

10/100/1000 Gigabit Network Adapter

Chapter 2: Getting to Know the 10/100/1000 Gigabit Network

Adapter

Port and LEDs

The Adapter’s port and LEDs are located on the metal panel.

RJ-45 Port The RJ-45 port is where you will connect your Ethernet network cable.

Gigabit LED Green. The Gigabit LED lights up when the Adapter is operating at 1000Mbps. If the Gigabit

LED is not lit and the PC is powered on, the Adapter has automatically determined that your

network is operating at a slower speed and adjusted accordingly.

Link/Act LED Orange. The Link/Act LED lights up when the Adapter is connected to a network. It flashes

when there is network activity.

Figure 2-1: Port and LEDs

Chapter 3: Installing the 10/100/1000 Gigabit Network Adapter in Your PC

Hardware Installation

10/100/1000 Gigabit Network Adapter

Chapter3:Installingthe10/100/1000GigabitNetworkAdapter

in Your PC

Hardware Installation

1. Power off your PC and any peripheral equipment attached to it. Unplug your PC’spower cord.

2. Open your PC’s case, and locate an available PCI slot on the motherboard. Check with your computer

manufacturer if you need instructions.

3. Remove the metal PCI slot cover on the back of the PC.

4. Insert the Adapter into the PCI slot. Make sure that all of its pins are touching the slot’s contacts. You may

have to apply a bit of pressure to slide the Adapter all the way in.

5. After the Adapter is set firmly in place, secure its fastening tab to your PC’s chassis with a mounting screw.

Then close your PC’s case.

6. Connect one end of the Ethernet network cable to the RJ-45 port of the Adapter. (Category 5e or better

Ethernet network cabling is required for Gigabit transmission speeds.)

7. Connect the other end of the Ethernet network cable to your network’s Gigabit hub or switch port.

8. Reconnect your PC’s power cord, and then power on your computer.

Now that the hardware installation is complete, you will install the appropriate Windows driver for the Adapter.

Proceed to the chapter for your PC’s operating system.

For Windows XP, go to “Chapter 4: Installing the Driver for Windows XP.”

For Windows 2000, go to “Chapter 5: Installing the Driver for Windows 2000.”

For Windows Millennium or 98SE, go to “Chapter 6: Installing the Driver for Windows Millennium or 98SE.”

Figure 3-1: Insert the Adapter into the PCI Slot

Figure 3-2: Set the Adapter Firmly in Place

Figure 3-3: Connect the Ethernet Network Cable

NOTE: For best results, Linksys recommends using

Category 5eor better Ethernet networkcabling.Thisis

the only cabling that will work for Gigabit transfer

speeds. (You can use Category 5 Ethernet network

cabling for 100Mbps or lower speeds.) The cable run

from the Adapter to the network hub or switch should

not exceed 328 feet (100 meters).

Andere Handbücher für EG1064

Inhaltsverzeichnis

Andere Linksys Netzwerkkarte Handbücher

Linksys

Linksys HPN200 Bedienungsanleitung

Linksys

Linksys Compact USB 2.0 Bedienungsanleitung

Linksys

Linksys PLE300 Bedienungsanleitung

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Bedienungsanleitung

Linksys

Linksys LNE100M Bedienungsanleitung

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Original Betriebsanleitung

Linksys

Linksys EG1032 Bedienungsanleitung

Linksys

Linksys WUSB11 ver. 2.6 Bedienungsanleitung

Linksys

Linksys 10/100 LAN Card 10/100 Bedienungsanleitung

Linksys

Linksys EG1032 Bedienungsanleitung

Linksys

Linksys EC2T Original Betriebsanleitung

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Bedienungsanleitung

Linksys

Linksys EC2T Original Betriebsanleitung

Linksys

Linksys USB200M Bedienungsanleitung

Linksys

Linksys Wireless USB Network Adapter Gebrauchsanweisung

Linksys

Linksys HP200 Bedienungsanleitung

Linksys

Linksys ETHERFAST 10/100 Bedienungsanleitung

Linksys

Linksys EtherFast LNE100TX ver. 5 Bedienungsanleitung

Linksys

Linksys WUSB200 Bedienungsanleitung

Linksys

Linksys LINKSYS WMP300N Bedienungsanleitung

Linksys

Linksys PCMPC100 - EtherFast 10/100 PC Card Bedienungsanleitung

Linksys

Linksys WCF11 - Wireless CompactFlash Card Type II Original Betriebsanleitung

Linksys

Linksys USB200HA Bedienungsanleitung

Linksys

Linksys WUSB54GX4 Bedienungsanleitung

Beliebte Netzwerkkarte Handbücher anderer Marken

FirstComm

FirstComm OBiWiFi5G Bedienungsanleitung

Sun Microsystems

Sun Microsystems Interface Adapter Bedienungsanleitung

TRENDnet

TRENDnet TU2-ETG Bedienungsanleitung

YASKAWA

YASKAWA SI-EN3 Bedienungsanleitung

Paradyne

Paradyne BitStorm 2600 IP DSLAM Bedienungsanleitung

Belkin

Belkin F5D7050 Bedienungsanleitung

3Com

3Com EtherLink 3C509B Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITX Bedienungsanleitung

Cisco

Cisco MC16E Bedienungsanleitung

Delta Electronics

Delta Electronics Braking Modules VFDB Series Bedienungsanleitung

TwinMOS

TwinMOS Booming Bedienungsanleitung

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Bedienungsanleitung

Buffalo

Buffalo AirStation WLI-PCM-L11GP Bedienungsanleitung

National Instruments

National Instruments NI 9234 Bedienungsanleitung

Hama

Hama 49276 Bedienungsanleitung

Compaq

Compaq Wireless LAN 100 Bedienungsanleitung

Bose

Bose PowerMatch Dante Bedienungsanleitung

TRENDnet

TRENDnet TEG-PCITXR Bedienungsanleitung