Lionel Command Control Gantry Crane Bedienungsanleitung
78-2097-250
9/16
Lionel
Command Control
Gantry Crane
Owner’s Manual
Lionel
Command Control
Gantry Crane
Owner’s Manual
2
Congratulations!
Congratulations on your purchase of the Lionel Command Control Gantry Crane! The
Gantry Crane is compatible with Legacy Cab-2 or Cab-1L, or with TMCC Cab-1 remotes.
Add sounds synchronized to the actions of the Gantry Crane with the Crane Sounds Work
House (6-82035, sold separately).
Features of the Trackside Crane
• Command Control equipped
• 360-degree cab rotation
• Manual up and down operation of the boom
• Forward and backward trackside movement of entire crane unit
• Independent control of the hook
• Electromagnet control for moving metal objects
• Three powerful maintenance-free motors
Trainmaster Command Control
Products equipped with the classic TrainMaster Command Control system are controlled
by commands from your CAB-1 or CAB-2 Remote Controller. ElectroCouplers™, basic
sounds, and multiple unit lash-ups are all at your fingertips as you walk around your
layout.
The following Lionel marks are used throughout this Owner’s Manual and are protected under
law. All rights reserved.
Lionel®, LionChief™, LionChief Plus™,TMCC®, LEGACY®, FasTrack®,TrainMaster®, Odyssey®,
RailSounds®, CrewTalk™, TowerCom™, DynaChuff™, StationSounds™, Pullmor®, ElectroCoupler™,
Magne-Traction®, CAB-1®Remote Controller, American Flyer®, Lionel ZW®, ZW®, MagniVision®,
TMCC®, Lionelville®, Wireless Tether™, Powerhouse™, LionMaster®, Conventional Classics™, Postwar
Celebration Series™, TruRail™, PH-1 Powerhouse®, Powermaster®, Powerstation-Powerhouse®,
Accessory Motor Controller™, AMC™, Accessory Switch Controller™, ASC™, Action Recorder
Controller™, ARC™, Track Power Controller 300™, TPC 300™, Track Power Controller 400™, TPC
400™, Block Power Controller™, BPC™, Operating Track Controller™, OTC™, FatBoy™, Lionel
Lines®, Joshua Lionel Cowen Series™, Lockon®, TrainSounds™, MultiHorn™, MultiWhistle™,
Choo-Choo™, SensorTrack™, Plug-Expand-Play™, Imagineering™, SensorCar™, LionScale™
3
Table of Contents
Gantry Crane basics
Preparing the Gantry Crane for operation 4
Powering your Gantry Crane 4
Assigning a new ID# to your Gantry Crane 5
Operating the Gantry Crane 6-7
Capabilities of the Gantry Crane 8
Operating the Gantry Crane
CAB-2 Remote Controller commands 9
CAB-1 and CAB-1L Remote Controller commands 10
Maintenance and Service
Storing the Gantry Crane 11
Lionel Limited Warranty Policy & Service 12
4
Preparing the Gantry Crane for operation
When you are ready to store your Gantry Crane, be sure to use the supplied elastic band to keep
tension on the hook line. Use your remote to position the boom to fit in the foam cavity.
Note Always keep light tension on the hook when handling the Gantry Crane.
Gantry Crane basics
Powering Your Gantry Crane
Your Gantry Crane is powered using track power. The Gantry Crane requires a special
track section for gantry unit motion available from other manufacturers (not included).
This track section has three rails in the middle for regular train operation, and two rails on
the outsides meant for Gantry Crane operation. Track positive connects to one of these rails,
and track negative to the other. The crane is reversible, so which rail is positive and which is
negative does not matter. See Figure 1 below for more information.
Power
(negative)
Boom down
Boom up
REAR OF CAB
Power
(positive)
Figure 1. 5 rail track power
Figure 2. Manually moving the boom up and down
Note Your Gantry Crane is factory programmed with an Engine ID# of “1.” To change
the ID#, see page 5.
5
As your fleet of LEGACY or TMCC equipped locomotives and equipment grows, you will want to
assign each unit a unique ID#. Use your CAB-1, CAB-1L, or CAB-2 Remote Controller.
1. Turn off power to the Gantry Crane.
2. Make sure that the Command Base is plugged in, then power up the crane.
3. Slide the RUN/PROGRAM switch to the PROGRAM position. Refer to Figure 3.
4. Press ENG or ACC.
5. Enter the ID# for the Gantry Crane using the numeric keypad on the Remote Controller.
Select any number between 1 and 98.
6. Press SET.
7. Slide the RUN/PROGRAM switch to the RUN position.
At this point, the new ID# has been set. When you power up, be sure to address the Gantry
Crane using the new ID#.
Assigning a new ID to your Gantry Crane
Figure 3. Switch location
When using the Legacy system the CAB-2 MUST be set to CAB-1 mode.
The crane will not respond to Legacy mode commands.
When using the CAB-1 or CAB-1L, the crane MUST be programmed as an
engine. The crane may be programmed as an accessory or an engine when
using a CAB-2.
Note!
Note!
Program/Run
switch
PRG
RUN
Gantry Crane basics
6
Gantry Crane basics
To operate the crane, you will need to use a Command Base and Remote Controller (LEGACY
CAB-2, CAB-1L, or CAB-1; all available separately).
Operating the Gantry Crane
Press ENG and 1 on the CAB-1, CAB-1L, or CAB-2 controller to select the Cab motor.
Rotate the THROTTLE knob clockwise on the CAB-1, CAB-1L, or
CAB-2 controller to rotate the cab clockwise.
Rotate the THROTTLE knob counter-clockwise on the CAB-1, CAB-
1L, or CAB-2 controller to rotate the cab counter-clockwise.
1
2
3
Cab-1 or Cab-1L remote LEGACY remote
The speed of the rotation of the boom is determined by
how fast the THROTTLE knob is rotated.
Note!
Operating the Cab Motor
7
Gantry Crane basics
Operating the Gantry Crane continued
Press 2 on the CAB-1, CAB-1L, or CAB-2 controller to select the Roll motor.
Rotate the THROTTLE knob clockwise on the CAB-1, CAB-1L, or
CAB-2 controller to make the Gantry Crane roll forward.
Rotate the THROTTLE knob counter-clockwise on the CAB-1, CAB-
1L, or CAB-2 controller to make the Gantry Crane roll backwards.
1
2
3
Cab-1 or Cab-1L remote
Cab-1 or Cab-1L remote
LEGACY remote
LEGACY remote
The speed that the crane rolls on the track is determined by how fast
the THROTTLE knob is rotated.
Pressing the DIR key on the CAB-1 or CAB-1L, or pressing down on
the BOOST/BRAKE button on the CAB-2 controller will reverse the
operation of the THROTTLE knob so that clockwise will move the
crane backwards and counter-clockwise will move the crane forward.
This allows the user to set it up so the control is intuitive based on
which side of the crane they are on. Setting is not retained when
power is turned off.
Note!
Note!
Operating the Roll Motor
8
Your Gantry Crane’s hook and electromagnet are capable of lifting approximately 4 oz (1/4
lb). The electromagnet automatically turns off after 60 seconds. The electromagnet cannot be
turned on again for 8 seconds.
Capabilities of the Gantry Crane
Gantry Crane basics
Press the BOOST key on the CAB-1, CAB-1L, or CAB-2 controller to raise the hook.
Operating the Hook Motor
Operating the Magnet
Press the BRAKE key on the CAB-1, CAB-1L, or CAB-2 controller to lower the hook.
1
2
Cab-1 or Cab-1L remote
Cab-1 or Cab-1L remote
LEGACY remote
LEGACY remote
The hook can be raised or lowered while the boom is being rotated or
while the crane is rolling.
Note!
Press the AUX2 key on the CAB-1, CAB-1L, or CAB-2 controller to toggle the Magnet
ON. If the magnet is left on it will turn off automatically after 60 seconds.
Press the AUX2 key again on the CAB-1, CAB-1L, or CAB-2 controller to toggle the
Magnet OFF. After the magnet is turned OFF it cannot be turned back on until it
has been off for 8 seconds.
1
2
Cab-1 or Cab-1L remote
Cab-1 or Cab-1L remote
LEGACY remote
LEGACY remote
9
The LEGACY CAB-2 Remote Controller
Rotates the cab and moves
the crane back and forth on
the gantry track.
Toggles the electromagnet
on and off.
Sets the throttle knob to
rotate the cab.
Sets the throttle knob to
control the roll motion of
the cab.
Raises and lowers hook.
Pressing DIR will switch
which direction the crane
moves on the gantry track
based on which direction
the throttle knob is rotated.
U
se your CAB-2 Remote Controller to operate your Gantry Crane.
Note
Note
Note
You can operate the hook while the cab is rotating or while the crane is moving.
We recommend that you keep a light weight on the hook for optimal performance.
The electromagnet will automatically turn off after 60 seconds. You must wait 8 seconds
before the electromagnet can be turned on again.
Do not allow the hook to go all the way down and then start to ascend again. If you
notice that the hook begins to ascend when it reaches its lowest point, press and hold
the BOOST button immediately to avoid reversing the controls.
Caution
Operating the Gantry Crane
10
CAB-1 & CAB-1L Remote Controller commands
Use your CAB-1 Remote Controller to operate the Gantry Crane.
Sets the throttle knob to rotate the cab.
Sets the throttle knob to control the roll
motion of the crane.
Lowers the hook on the crane.
Raises the hook on the crane.
Turns on the magnet.
Moves the crane back and forth along the gantry
track or rotates the cab.
Do not allow the hook to go all the way down and then
start to ascend again. If you notice that the hook begins to
ascend when it reaches its lowest point, press and hold the
BOOST button (up arrow) immediately to avoid reversing
the controls.
Caution
Note You can operate the hook while the
cab is rotating or while the crane
is moving.
Note
Note
We recommend that you
keep a light weight on the
auxiliary hook for optimal
performance.
The electromagnet will automatically turn off after 60 seconds. You must wait 8
seconds before the electromagnet can be turned on again.
Operating the Gantry Crane
Inhaltsverzeichnis
Andere Lionel Spielzeug Handbücher
Lionel
Lionel Glacier Route Freight Ready-To-Run Train Set Bedienungsanleitung
Lionel
Lionel Floodlight Tower Bedienungsanleitung
Lionel
Lionel Aquarium Car Bedienungsanleitung
Lionel
Lionel 21" Passenger Cars Bedienungsanleitung
Lionel
Lionel Searchlight Car Bedienungsanleitung
Lionel
Lionel Santa's Sleigh Pylon Bedienungsanleitung
Lionel
Lionel Bay WindowCrew Talk Caboose Bedienungsanleitung
Lionel
Lionel Honda Flyer Train Set Bedienungsanleitung
Lionel
Lionel FasTrack Grade Crossing with Flashers Bedienungsanleitung
Lionel
Lionel Tinplate 392 Steam Locomotive Bedienungsanleitung
Lionel
Lionel American Flyer Bedienungsanleitung
Lionel
Lionel Powered F7 B-Unit Diesel Locomotive Bedienungsanleitung
Lionel
Lionel Satellite Launch Car Bedienungsanleitung
Lionel
Lionel Hudson Jr. Bedienungsanleitung
Lionel
Lionel Junction Dinosaur Diesel LionChief Ready-To-Run... Bedienungsanleitung
Lionel
Lionel Building Set Bedienungsanleitung
Lionel
Lionel American Flyer GP-7 Bedienungsanleitung
Lionel
Lionel 352 Icing Station Bedienungsanleitung
Lionel
Lionel 238E Torpedo 4-6-2 steam locomotive Bedienungsanleitung
Lionel
Lionel Three Rivers Fast Freight Bedienungsanleitung
