Lionel Fastrack 060 Remote Switch Bedienungsanleitung
71-2057-250
12/04
Lionel
O60 Remote Switch
Owner’s Manual
Congratulations on your purchase of the Lionel FasTrack O60 Remote Switch! This switch
features a non-derailing function, a lighted switch lamp, and a lighted controller. The
switch connects easily to other FasTrack track sections. Use the switch to join two track loops,
create a switching yard, or add a siding.
2
The following Lionel marks may be used throughout this instruction manual and are protected under law.
All rights reserved.
Lionel®, TrainMaster®, Odyssey®, RailSounds®, CrewTalk™, TowerCom™, DynaChuff™,
StationSounds™, Pullmor®, ElectroCoupler™, Magne-Traction®, CAB-1®Remote Controller,
PowerMaster®, Lionel ZW®, ZW®, PowerHouse®, TMCC®, Lionelville™, Lockon®, Wireless Tether™,
LionMaster®
The name FasTrack®is used with permission from Pitsco, Inc.
Table of contents
Joining the FasTrack track sections 3
Using the track extensions 3
Operating the switch 4
Changing the switch stand location 5
Routing the controller cable 6
Mounting the controllers 7
Numbering your switch controllers 7
Powering the switch through a separate power supply 8
Connecting the controller 9
Operating the switch in the TrainMaster Command Control environment 9-10
Servicing the lamps 11
Limited Warranty/Lionel Service 12
3
Joining the FasTrack track sections
FasTrack track sections join together easily.
With interlocking roadbed sections and
large rail tabs, the track fits together securely
so you always get good electrical contact. Refer
to Figure 1 to see how to join the track
sections.
1. Line up your two sections of track.
2. Insert the rail tabs into the openings at the
ends of the corresponding rails.
3. Press the sections together until the
interlocking roadbed snaps into place.
Figure 1. Joining the track sections
Rail tab
Using the track extensions
Three track extensions are included with your switch. Two of the extensions have beveled
roadbed on one side, and the other has no roadbed. The extensions work with the geometry
of the FasTrack roadbed.
To join the switch with a regular section of track, you will need to use an extension with
beveled roadbed. To join the track with another switch (larger than O36), a wye, or a 22.5
degree crossover, you will need to use an extension without roadbed. Refer to Figure 2.
Figure 2. Track extensions
Using two extensions
with roadbed,the
track are spaced
further apart.You
may choose to add
additional straight
sections between
the extensions.
Note!
Using one extension
without roadbed,two
mainlines are joined
by two switches.The
tracks keep 6”
centers.
Note!
Extension with roadbed
Extension with roadbed
Extension with roadbed
Extension without roadbed
4
Operating the switch
You may operate the switch using the controller or the illuminated switch lamp on the
roadbed. Refer to Figure 3.
To operate the switch using the controller, power up the track, then pull the lever to the
opposite position. Gently press the lever past the end of its path. The lights inside the controller
will change colors to designate the change in switch positions. The red lights designate the
curved path. The green lights designate the straight path.
Track power must be on to operate the switch using the controller.
To operate the switch using the switch lamp, simply rotate the switch lamp. The new
position of the colored lenses on the lamp designate the change in switch positions.
This switch is equipped with a non-derailing feature. The train’s wheels
automatically throw the blades to the proper position when the train travels toward
the converging track. If you experience difficulties, simply use the controller or
switch lamp to throw the switch into the correct position for the train to travel.
Figure 3. Switch operation
Note!
Note!
Controller
Switch lamp
5
Changing the switch stand location
You may choose to position the switch stand either inside or outside the loop of track. Follow
these steps and refer to Figure 4 to change the location of the switch stand.
1. Remove the two screws that secure the small roadbed section to the switch and lift away the
roadbed section.
2. Place the “blades,” or moving rails, in the proper position to make removing the switch
stand roadbed section easier.
• If the switch stand is being removed from the curved side, the blades should be set to the
through/straight position.
• If the switch stand is being removed from the straight side, the blades should be set to
the out/curve position.
3. Remove the two screws that secure the switch stand roadbed section to the switch. Please
note that these screws are located towards the inside edge of the switch stand roadbed
section. Lift away the switch stand roadbed section.
4. Install the switch stand roadbed section at its new location. The posts on the switch should
be inserted into the holes on the switch stand roadbed section. The pin on the switch stand
mechanism should be inserted into the slot on the switch control arm. Insert the two screws
to secure the switch stand.
5. Install the small roadbed section, securing it in place with the two screws.
Figure 4. Switch stand installation
Remove these screws
Small roadbed section Slot
Pin
Switch stand
roadbed section
Routing the controller cable
You may choose to route the controller cable through the notch on either side of the
roadbed. As illustrated in Figure 5, simply bend the tabs to free the cable and reroute the
wire. Once the cable is in place, bend down the tabs to hold the wire in the channel. Remove the
notch section of roadbed and route the wire through the notch. Snap the notch section of
roadbed on the other side to hide the notch.
6
TRACK
JUMPER
AUX
IN
AUXILIARY POWER
AUX
GND
RSC
LIGHTS
REMOTE SWITCH CONTROLLER
OUT GND THRU
Figure 5. Controller cable
Notch section
Notch section
Metal tab
Metal tab
Cable
Mounting the controllers
If you have multiple switches and controllers, you may choose to snap the interlocking
controller bases together and mount them to your control panel using screws. To join the
controller bases, snap the bases together on a flat surface as illustrated in Figure 6. Drive screws
through the holes in the controller bases to secure the controllers to your layout. We
recommend using No. 4 sheet metal screws.
7
Figure 6. Joining the controllers
Hole
Hole
Numbering your switch controllers
You may choose to number your switch controllers to help you identify the switches on your
layout. Six numbered lenses are included with your switch.
To number a switch, slide the logo lens out from under the left side of the frame, then insert
the numbered lens. Refer to Figure 7.
Figure 7. Inserting a numbered lens
Frame
Insert the lens under the frame
Powering the switch through a separate power supply
You may choose to connect the switch to a separate power supply to operate the switch when
track power is off or set to a low voltage. This is most beneficial to those operating in the
conventional environment. The switch operates best at 5-18 volts (AC). Follow these steps and
refer to Figure 8 to make the proper connections.
1. Remove the jumper between the TRACK JUMPER and AUX IN terminals on the underside of
the switch. Loosen the terminal screws and slide out the jumper.
We recommend that you save the track jumper in a safe place for reverting to track
power in the future.
2. Connect the Power/A terminal on your power supply to the AUX IN terminal on the switch.
3. Connect the Common/Ground/U terminal on your power supply to the AUX GND terminal
on the switch.
8
TRACK
JUMPER
AUX
IN
TRACK
JUMPER
AUX
GND
AUX
IN
AUXILIARY POWER
AUXILIARY POWER
AUX
GND
Figure 8. Power supply connections
Jumper
Note!
Connecting the controller
The four controller wires are attached to the terminals on the underside of the switch. The
controller wires were attached at the factory. The connections are as follows: green wire to
THRU, black wire to GND, red wire to OUT, and yellow wire to RSC LIGHTS.
Operating the switch in the TrainMaster Command Control
environment
You may choose to operate the switch in the TrainMaster Command Control environment
using the Accessory Switch Controller (available separately, 6-14182) or the SC-2 Switch
Controller (available separately, 6-22980). Refer to these manuals for additional information.
You may choose to leave the controller attached to operate the switch without your
CAB-1 Remote Controller.
ASC connections
The Accessory Switch Controller is capable of controlling up to four remote switches at a
time. Wire the switches to the terminals on the back of the ASC unit as illustrated in Figure 9.
1. Attach a wire to the THRU terminal on the switch and connect it to the 1T terminal on the
ASC unit.
2. Attach another wire to the OUT terminal on the switch and connect it to the 1O terminal on
the ASC unit.
3. Attach the final wire to the GND terminal on the first switch and connect it to the COMM
terminal to the right of the 1T and 1O terminals on the ASC unit.
4. Repeat this process for any additional switches, filling the empty switch terminals on the
ASC in the same way.
9
RSC
LIGHTSOUTGNDTHRU
ToManual
Controller
THRUGNDOUTRSC
LIGHTS
To Manual
Controller
Figure 9. ASC connections
Note!
Underside of
the switch
Controller cable
Controller cable
Operating the switch in the TrainMaster Command Control
environment (continued)
SC-2 connections
The SC-2 is capable of controlling up to five remote switches at a time. Wire the switches to
the terminals on the back of the SC-2 unit as illustrated in Figure 10.
Do not connect your FasTrack switch to the #1 terminal on the SC-2.
1. Attach a wire to the THRU terminal on the switch and connect it to the THROUGH (single
arrow) terminal on the SC-2 unit.
2. Attach another wire to the OUT terminal on the switch and connect it to the OUT (double
arrow) terminal on the SC-2 unit.
3. Attach the final wire to the GND terminal on the first switch and connect it to the COMM
(center) terminal on the SC-2 unit.
4. Repeat this process for any additional switches, filling the empty switch terminals on the
SC-2 in the same way.
10
RSC
LIGHTS OUTGNDTHRU
To Manual
Controller
THRUGNDOUTRSC
LIGHTS
To Manual
Controller
ACC2 ACC2
ACC1 ACC1
Figure 10. SC-2 connections
Underside of
the switch
Controller cable
Controller cable
Note!
Inhaltsverzeichnis
Andere Lionel Spielzeug Handbücher
Lionel
Lionel Genset Diesel Locomotive Bedienungsanleitung
Lionel
Lionel 4-4-2 Atlantic Bedienungsanleitung
Lionel
Lionel 726 Berkshire 2-8-4 steam locomotive Bedienungsanleitung
Lionel
Lionel Union Pacific RS-3 Bedienungsanleitung
Lionel
Lionel B40-8 Bedienungsanleitung
Lionel
Lionel Railroad Control Tower Bedienungsanleitung
Lionel
Lionel LionChief Plus 2.0 ET44 Bedienungsanleitung
Lionel
Lionel Three Rivers Fast Freight Bedienungsanleitung
Lionel
Lionel Ready-to-Run Riding the Rails Hobo Train Bedienungsanleitung
Lionel
Lionel New York Central FlyerReady-To-Run O-27 Set Bedienungsanleitung
Lionel
Lionel 2-8-4 Berkshire Locomotive and Tender Bedienungsanleitung
Lionel
Lionel Railroad Speeder Bedienungsanleitung
Lionel
Lionel 352 Icing Station Bedienungsanleitung
Lionel
Lionel General AmericanMilk Car Bedienungsanleitung
Lionel
Lionel VISIONLINE Big Boy Bedienungsanleitung
Lionel
Lionel Amtrak Acela Bedienungsanleitung
Lionel
Lionel Operating Carousel Bedienungsanleitung
Lionel
Lionel Illuminated Station Platform Bedienungsanleitung
Lionel
Lionel FT Passenger LionChief Bedienungsanleitung
Lionel
Lionel U.S. ARMY SWITCHER 41 Bedienungsanleitung
