Lionel SD60 Bedienungsanleitung
Featuring
72-8312-250
7/11
Lionel
SD60 Diesel Locomotive
Owner’s Manual
Lionel
SD60 Diesel Locomotive
Owner’s Manual
2
Congratulations!
Congratulations on your purchase of this Lionel LEGACY diesel locomotive! On the outside, this
locomotive features numerous details and expert decoration in your favorite livery. Inside the
body, this locomotive is equipped with some of the most advanced sounds and controls in model
railroading. This powerful locomotive is ready for duty on your layout.
The following Lionel marks are used throughout this catalog and are protected under law. All rights
reserved.
Lionel®, LEGACY™, FasTrack™, TrainMaster®, Odyssey®, RailSounds®, CrewTalk™, TowerCom™,
DynaChuff™, StationSounds™, Pullmor®, ElectroCoupler™, Magne-Traction®, CAB-1® Remote
Controller, American Flyer®, Lionel ZW®, ZW®, MagniVision®, TMCC®, Lionelville®, Wireless
Tether™, Powerhouse™, LionMaster®, Conventional Classics™, Postwar Celebration Series™,
TruRail™, PH-1 Powerhouse®, Powermaster®, Powerstation-Powerhouse®, Accessory Motor
Controller™, AMC™, Accessory Switch Controller™, ASC™, Action Recorder Controller™, ARC™,
Track Power Controller 300™, TPC 300™, Track Power Controller 400™, TPC 400™, Block Power
Controller™, BPC™, Operating Track Controller™, OTC™, FatBoy™, Lionel Lines®, Joshua Lionel
Cowen Series™, Lockon®, TrainSounds™, MultiHorn™, MultiHorn™, Choo-Choo™
Contents of your locomotive box
1 Locomotive
4 Replacement traction tires
1 Owner's manual
1 Engine memory module
3
Table of contents
Running your locomotive
LEGACY Control operations 4
TrainMaster Command Control (TMCC/Command) operations 5
Conventional/transformer operations 6
Locomotive basics
Adding smoke fluid to your locomotive's smoke generator 7
Locomotive switch locations 8
Installing the battery 9
Assigning your locomotive a new ID# (LEGACY and TMCC) 10
Building a lash-up 10
LEGACY Control System operations
The LEGACY CAB-2 Remote Controller 11
The Velocity Throttle 12
The Multi-Controller 12
The Train Brake Slider 12
The Warning Sound Controller 13
The Speed Bar 13
EFX Trim and EFX Bar Graph 14
Leaving the Preset Speed Screen 14
LEGACY RailSounds Sound System operations
LEGACY RailSounds sound system 15
LEGACY RailSounds Sequence Control 16
CrewTalk dialog and TowerCom announcements in the LEGACY environment 17
LEGACY RailSounds sound system dialog on a round trip 18
TrainMaster Command Control operations
CAB-1 Remote Controller commands 19
CAB-1 Remote Controller numeric keypad commands 20-21
Setting the smoke level 21
Conventional transformer operations
Using the LEGACY RailSounds sound system in the conventional environment 22
Activating CrewTalk dialog and TowerCom announcements 23
Locking your locomotive into a single direction 23
Odyssey II Speed Control system operations
Odyssey II Speed Control operations 24
Odyssey II Speed Control system LEGACY Control operation 24
Odyssey II Speed Control system TrainMaster Command Control operation 24
Odyssey II Speed Control system conventional transformer operation 24
Maintaining and servicing your locomotive
Reprogramming your locomotive to restore features 25
Lubricating your locomotive 26
Servicing your locomotive’s lamps 27
Replacing the traction tires 27
Locomotive Diagnostics 27
Lionel Warranty 28
4
Power your locomotive with an alternating-current (50-60Hz AC) transformer only.
Powering your locomotive with a direct-current (DC) transformer, or in excess of
19 volts AC, may result in damage to sensitive electronic components.
Your locomotive requires Lionel or Lionel-compatible O-31 or larger track curves.
1. Turn off track power, and then plug in the
LEGACY Base and connect it to the track.
2. Place your locomotive on the track.
3. Increase track power voltage to full power
(no more than 19 volts AC). If a circuit breaker
trips when you turn on the Lionel power supply, check
the wheels of your locomotive to make sure they are all
securely on the track. Check to make sure the track is free
of all metals that may cause a short circuit.
4. As illustrated in Figure 1, press ENG and 1
(or your selected ENG ID#) to address the
locomotive with your LEGACY CAB-2 Remote
Controller.
5. Press Start Up on your LEGACY CAB-2 Remote,
shown in Figure 2. Then, throttle up and move
'em out! Your engine sound will start up, and the
locomotive-specific touch screen buttons will populate
the remote. For more information on operating your
locomotive with the LEGACY system, please refer to the
LEGACY section of this manual. Additional information
is also found in the LEGACY System Manual, available
online at www.lionel.com.
.
Note!
Note!
Running your locomotive
Figure 1. LEGACY engine selection
Figure 2. LEGACY start-up
LEGACY Control operations
For the finest operating experience, your locomotive is fully compatible with the LEGACY Control
System. To operate in LEGACY mode, you need a LEGACY Command Base and LEGACY CAB-2
Remote Controller (6-14295).
Your commands are sent by the CAB-2 Remote Controller to the Command Base, which sends
a digital code through the rails to your locomotive. Your locomotive will not respond until it
recognizes its unique ID#, so you can operate multiple Command-equipped locomotives on the
same track at the same time.
5
Running your locomotive
Power your locomotive with an alternating-current (50-60Hz AC) transformer only.
Powering your locomotive with a direct-current (DC) transformer, or in excess of
19 volts AC, may result in damage to sensitive electronic components.
Your locomotive requires Lionel or Lionel-compatible O-31 or larger track curves.
TrainMaster Command Control (TMCC/Command Control) operations
For users operating in the your locomotive in the Command Control environment, you need a
TrainMaster Command Base (6-12911) and a CAB-1 Remote Controller (6-12868). Refer to your
TMCC System Manual for complete information.
Your commands are sent by the CAB-1 Remote Controller to the Command Base, which
translates the command into digital code. That code is sent through the outside rails to your
locomotive, which will not respond until it recognizes its unique ID#. TrainMaster Command
Control gives you the power to operate multiple Command-equipped locomotives on the same track
at the same time.
1. Turn off track power, and then plug in the Command Base and connect it to the
track.
2. Place your locomotive on the track.
3. Increase track voltage to full power (no more than 19 volts AC). If a circuit
breaker trips when you turn on the Lionel power supply, check the wheels of your locomotive to
make sure they are all securely on the track. Check to make sure the track is free of all metals
that may cause a short circuit.
4. Press ENG and 1 to address your locomotive with your CAB-1 Remote
Controller.
5. Throttle up and move ‘em out.
For more information, please refer to the TrainMaster Command Control operations section of
this manual or the TMCC System Manual, available online at www.lionel.com.
Note!
Note!
6
Running your locomotive
Conventional transformer operations
For conventional operation, a Command Base must not be powered up anywhere in
the area, even if it is not connected to the track. If a base is detected, your
locomotive will default to command mode.
Power your locomotive with an alternating-current (50-60Hz AC) transformer only.
Powering your locomotive with a direct-current (DC) transformer, or in excess of
19 volts AC, may result in damage to sensitive electronic components.
Your locomotive requires Lionel or Lionel-compatible O-31 or larger track curves.
1. With track power off, place your locomotive on the track.
2. Power up the track. If a circuit breaker trips when you turn on the Lionel power supply,
check the wheels of your locomotive to make sure they are all securely on the track. Check to
make sure the track is free of all metals that may cause a short circuit.
3. Move ‘em out! When the locomotive’s headlight illuminates and the LEGACY RailSounds
sound system starts, press the DIRECTION button on your transformer to sequence your
locomotive through the repeating pattern of operations: neutral, forward, neutral, reverse,
neutral, and so on. You may also briefly turn off track power to advance the locomotive to the
next operating state. Adjust the throttle until your locomotive moves at your desired speed.
When placing your locomotive on your layout for the first time and after power
interruptions lasting longer than five seconds, it will start out in neutral.
We recommend that you operate your LEGACY locomotive with The Odyssey II
Speed Control System turned on. You may choose to operate your locomotive without speed
control by placing the Odyssey II Speed Control System switch to the OFF position. See Figure 4 on
page 8.
Use the HORN and BELL buttons on your transformer to activate those features. Adjust the
volume using the volume control knob, which is located on the underside of the locomotive.
Refer to Figure 4 on page 8. For more information, please refer to the Conventional transformer
operations section of this manual.
Note!
Note!
Note!
Note!
7
Locomotive basics
Your locomotive is equipped with a smoke generator that produces safe, clean, white smoke dur-
ing operation. Add 10-20 drops to the duct (shown in Figure 3) to prime the unit the first time
you run the locomotive or after being stored for an extended period of time, and then add 10 to 20
drops to refill when smoke production decreases. When refilling, DO NOT EXCEED 20 DROPS as this
can cause your smoke units to become oversaturated allowing leakage onto the electronics. Note
that operating your locomotive’s smoke unit without smoke fluid will cause damage to the heating
element.
If you prefer to operate your locomotive without smoke, locate the smoke unit switch on the
underside of the locomotive and slide it to the OFF position. Refer to Figure 4 on page 8 for the
location of these switches.
For best performance, we recommend using Lionel smoke fluid only.
Adding fluid to your locomotive’s smoke generator
Figure 3. Smoke fluid location
Note!
FRONT
Exhaust duct. Add smoke
fluid here.
REAR
8
SMK NO SMK
ODY NO ODY RUN PGM
The functions of your locomotive's switches are outlined below. Refer to Figure 4 for the location
of the switches. Note that available features (and switches) will vary by loco-
motive.
Smoke Unit Switch (MAIN SMK)
Used to turn the main smoke stack unit function on and off.
Program-Run Switch (RUN/PGM)
Used to assign an ID# and reprogram the locomotive in LEGACY and Command operation when
the switch is in the PGM position. Also used to “lock” your locomotive in a single direction, or
neutral, in conventional operation when the switch is placed in the PGM position.
Odyssey II Speed Control System Switch (ODY)
Used to turn the Odyssey II Speed Control System on and off.
Figure 4. Locomotive switch locations
Front of Locomotive
Smoke unit On/Off
switch
Locomotive basics
Locomotive switch locations
Command reverse unit
switch
Odyssey II On/Off
switch
Volume control knob
(located on frame
above the truck)
9
Locomotive basics
Installing the battery
Although the LEGACY RailSounds sound system is powered through the track, you may choose
to install a nine-volt alkaline battery if you find that the sound system shuts down during
track power interruptions (for example, at a switch or over a dirty section of track). Follow these
steps to install the battery.
If the RailSounds sound system turns off during interruptions in track power, you may
need to replace the battery. Use only alkaline batteries.
1. Remove the body screws from the underside of the locomotive. Refer to
Figure 9 page 26.
2. Lift the body off the frame.
3. Snap the battery harness onto the nine-volt alkaline battery’s terminals. See
Figure 5 below.
4. Slide the battery into the battery holder.
5. Replace the body and secure it with the body screws. Be careful to avoid
pinching wires. Do not overtighten the screws.
Note!
Inside the Locomotive
Battery harness
Battery holder
Battery
Figure 5. Battery installation
10
For operation in the LEGACY or Command Control environment, you will want to give each unit
a unique ID#. The locomotive will respond to commands associated with its ID# while all other
units will disregard these commands. This procedure is not necessary for convention-
al (non-Command) operation.
1. Slide the program run switch on your locomotive to the PROG position. See
Figure 4 on page 8.
2. Place the locomotive on the track.
3. Connect the Command Base and plug it in.
4. Power up the track.
5. Press ENG on the CAB-1 or CAB-2 remote.
6. Enter the unique ID#. Choose any number from 1 to 98 that has not been
assigned to another locomotive (ENG). We recommend using a part of your
locomotive’s road number.
All LEGACY locomotives respond to ENG 99. We recommend that you reserve ID# 99 as a
"universal" ID#.
7. Press SET. The locomotive’s horn will sound, or the headlights will flash if the
RailSounds sound system is off.
8. Slide the program run switch back to the RUN position.
The locomotive’s ID# has been set. Be sure to record the new ID# for your reference.
Locomotive basics
Assigning your locomotive a new ID#
Note!
Building a lash-up
T
his LEGACY-equipped locomotive can be operated in conjunction with other LEGACY-equipped
locomotives, forming a multiple unit lash-up. Just like with the real railroads, lash-ups
allow you to pull longer trains and climb steeper grades. You will find that the lighting operates
prototypically—the lead unit’s headlight and interior lights are illuminated when the train is in
forward, and the rear unit’s headlight and interior lights are on when the train is in reverse. When
addressing the locomotives as a lash-up, the front ElectroCoupler on the lead unit and the rear
ElectroCoupler on the trailing unit are activated using the ElectroCoupler buttons on your remote.
For more information, refer to your complete LEGACY Control System manual.
Andere Handbücher für SD60
1
Inhaltsverzeichnis
Andere Lionel Spielzeug Handbücher
Lionel
Lionel U28C Bedienungsanleitung
Lionel
Lionel 73-0020-250 Bedienungsanleitung
Lionel
Lionel Zenith Express Bedienungsanleitung
Lionel
Lionel Pennsylvania S-2 Bedienungsanleitung
Lionel
Lionel Charles Bowdish Homestead Bedienungsanleitung
Lionel
Lionel Monopoly Hudson Steam Locomotive Bedienungsanleitung
Lionel
Lionel Drawbridge Bedienungsanleitung
Lionel
Lionel 4-6-9 Camelback Bedienungsanleitung
Lionel
Lionel Alco PA-1 Bedienungsanleitung
Lionel
Lionel Hot Rod GP-9 Bedienungsanleitung
Lionel
Lionel 4-6-4 Dreyfuss Hudson Bedienungsanleitung
Lionel
Lionel Holiday Special Train Set Bedienungsanleitung
Lionel
Lionel Boom Car Bedienungsanleitung
Lionel
Lionel New York Central Flyer Bedienungsanleitung
Lionel
Lionel Santa Fe Super Freight Bedienungsanleitung
Lionel
Lionel 71-4156-250 Bedienungsanleitung
Lionel
Lionel C&NW 0-8-0 Bedienungsanleitung
Lionel
Lionel Ready-to-Play Series Bedienungsanleitung
Lionel
Lionel American Flyer 787 Log Loader Bedienungsanleitung
Lionel
Lionel The GENERAL 4-4-0 Steam Locomotive Bedienungsanleitung
