Lippert Curt 18088 Bedienungsanleitung
CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •18088-INS-RA •07/06/2021 •ECN7705 •PAGE 1
Product Registration and Warranty
CURT stands behind our products with
industry-leading warranties. To get copies
of the product warranties, register your
purchase or provide feedback, visit:
warranty.curtgroup.com/surveys
Weight Carrying Capacity
1 bike 65 lbs.
2 bikes 130 lbs.
INSTALLATION MANUAL 18088
Tools Required
Torx wrench, T-27
(included)
Box wrench,
13mm / 14mm
(included)
Hex drive wrench,
5mm (included)
--
Level of Difficulty
Easy
Installation difficulty levels are based on time
and effort involved and may vary depending on
the installer level of expertise, condition of the
vehicle and proper tools and equipment.
WARNING
Never exceed the vehicle manufacturer's recommended towing capacity.
Never exceed the product's weight capacity.
Do not modify or use this accessory for purposes other than for which it was designed.
It is the user's responsibility to adhere to all state and federal laws regarding
obstruction of vehicle lighting (i.e. brake lights, taillights, turn signals
and backup lights) and license plate when using this accessory.
NOTICE
Visit www.curtmfg.com for a full-color copy of this
instruction manual, as well as helpful videos, guides and much more!
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
Remove this accessory before entering automatic car washes.
Periodic inspection of your product should be performed
to ensure all hardware and / or components remain secure.
CAUTION
This product is not designed for off-road use.
Do not install this product on a trailer or towed vehicle.
When transporting heavier bikes such as e-bikes and tilting the rack for rear vehicle
access is necessary, a team lift may be required to prevent injury and / or product damage.
Always be mindful of accessories extending beyond vehicle when operating.
Parts List
Item Qty Description
1 2 Tray assembly
2 1 Shank assembly
3 2 Tire / frame hook assembly
4 2 Wheel basket
5 2 Tray spacer
6 2 Wheel strap sleeve
7 2 Key
8 1 Clevis pin, 1/2"
9 2 Button head cap screw,
M6–1.0 x 10mm
10 4Button head cap screw,
M8–1.25 x 35mm
11 4Nylock nut, M8–1.25
12 4Carriage bolt, 3/8"-16 x 4"
13 4Flat washer, 3/8"
14 4Nylock nut, 3/8"-16
Product Photo
CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •18088-INS-RA •07/06/2021 •ECN7705 •PAGE 2
(2)
F
Torx wrench,
T-27
Hex drive
wrench, 5mm
Box wrench,
13mm / 14mm
ASSEMBLY
10 11
12 13 14
9
8
7
6
5
4
3
2
1
Parts List
Item Qty Description
1 2 Tray assembly
2 1 Shank assembly
3 2 Tire / frame hook assembly
4 2 Wheel basket
5 2 Tray spacer
6 2 Wheel strap sleeve
7 2 Key
8 1 Clevis pin, 1/2"
9 2 Button head cap screw,
M6–1.0 x 10mm
10 4Button head cap screw,
M8–1.25 x 35mm
11 4Nylock nut, M8–1.25
12 4Carriage bolt, 3/8"-16 x 4"
13 4Flat washer, 3/8"
14 4Nylock nut, 3/8"-16
CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •18088-INS-RA •07/06/2021 •ECN7705 •PAGE 3
Step 2
Align and slide a tire / frame hook assembly
(#3) onto the arm of the tray assembly (#1)
as shown. Ensure the hook is facing inward
toward the tray and the release button
is facing upwards.
Thread an M6 button head cap screw (#9)
into the hole at the end of the tray assembly
arm as shown. Tighten firmly with
the provided T-27 Torx wrench.
Step 3
Align and slide a wheel strap sleeve (#6) over
the tray assembly (#1) wheel strap as shown.
Repeat steps 1 through 3
for the other tray assembly.
Step 1
Place an M8 nylock nut (#11) into
each hex-shaped hole on one of
the wheel baskets (#4) as shown.
Place the wheel basket (#4) onto one of the
tray assemblies (#1), aligning the wheel basket
holes with those in the tray. Ensure the tallest
portion of the wheel basket is positioned
towards the center of the tray assembly.
Secure the wheel basket with M8 button
head cap screws (#10) using the provided
5mm hex drive wrench. Tighten the M8
hardware firmly without crushing the tray.
CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •18088-INS-RA •07/06/2021 •ECN7705 •PAGE 4
Step 5
Orientate the remaining tray assembly
onto the shank assembly (#2) as shown,
aligning the holes in each. Proceed to
assemble with hardware (#5, #12, #13
and #14) as completed in step 4.
Step 4
Orientate the tray assembly with the CURT logo
onto the shank assembly (#2) as shown. Align
the tray holes with those in the shank assembly.
Place a tray spacer (#5) onto the tray, aligning
its holes with those in the tray. Insert two 3/8"
carriage bolts (#12) through the spacer, tray and
shank assembly. Place a 3/8" flat washer (#13)
and 3/8" nylock nut (#14) onto each bolt.
Tighten each nut firmly with the
provided M14 wrench without
crushing the shank assembly tube.
Step 6
Insert the shank into a 2" receiver, aligning
the holes of the shank with the holes of the
receiver. Insert a 1/2" clevis pin (#8) and latch.
Rotate the anti-rattle knob clockwise
until there is firm resistance to turning.
To discourage theft, insert the key (#7) under
the rubber cover and turn a 1/2-turn clockwise.
The knob is now disengaged and
cannot be tightened or loosened.
INSTALL ATION AND USE
CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •18088-INS-RA •07/06/2021 •ECN7705 •PAGE 5
Step 7
To adjust the rack between vertical, horizontal
and tilted positions, squeeze the trigger on the
handle and rotate clockwise. Adjust the rack
position and release the handle. A 'click' will
be heard when the rack reaches its horizontal
or vertical position.
Step 8
With the rack positioned horizontally, place a
bike onto one of the trays with the front tire
nested into the wheel basket. Raise the arm
with the hook assembly into position over the
tire and frame. Depress and hold the hook
assembly lever while sliding the hook assembly
along the arm if adjustment is necessary for
positioning. Push the hook downward
into position firmly as shown.
NOTICE
For bikes equipped with a fork-mounted
brake caliper, take care not to damage
the caliper with excessive force.
Step 9
To discourage theft, pull the locking cable
from the arm and pull through the bike frame.
Press the tip of the cable firmly into the locking
mechanism hole until a 'click' is heard.
To remove the cable, insert the key, turn
and hold while pulling the cable from the lock.
Feed the cable back inside the arm and push
the cable end firmly until it snaps into place.
CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •18088-INS-RA •07/06/2021 •ECN7705 •PAGE 6
Step 10
Position the wheel strap to be centered
on the bike's rear wheel. Insert the strap
into the latch as shown. Adjust the wheel
strap sleeve (#6) over the wheel and
pull the strap firmly through the latch.
To remove the strap, press and hold the release
lever while pulling the strap from the latch.
Step 11
To allow rear-vehicle access, the rack can be
tilted away from the vehicle. Support the rack
while rotating the release handle clockwise
allowing the rack to stop at its lowest position.
WARNING
When transporting heavier bikes such
as e-bikes, a team lift may be required
when changing rack positions to prevent
injury and / or product damage.
Do not transport the rack in the lowest position as
this may cause damage to the product or cargo.
Step 12
When transporting the rack with an empty tray
or trays, the rack components must be secured
as shown. Place the tire / frame hook beneath
the tray. Slight downward pressure on the
arm may be necessary while sliding the hook
inward. Ensure the wheel strap is buckled
and the cable is inserted fully into the arm.
When unloaded, the rack may be
transported in the vertical position.
Inhaltsverzeichnis
Andere Lippert Fahrradzubehör Handbücher
Beliebte Fahrradzubehör Handbücher anderer Marken
Sigma
Sigma BC 16.16 Bedienungsanleitung
Playcore
Playcore Dero Setbacks Bedienungsanleitung
VDO Cyclecomputing
VDO Cyclecomputing x3dw Bedienungsanleitung
Cateye
Cateye RAPID X2 Bedienungsanleitung
buratti meccanica
buratti meccanica Clorofilla Trail Bedienungsanleitung
Shimano
Shimano SG-8R20 Betriebsanleitung
