Lockly MORTISE EDITION SECURE LUX PGD829AFUS Bedienungsanleitung
MORTISE EDITION
SECURE LUX
INSTALLATION MANUAL
INSTALLATION OVERVIEW
Door Frame
S
T
U
2X
KA4 X 18mm Screw
Strike Dust Box
A
B
E
2X
F
GH
4X
C
2X
PM4 X 10mm Screw
Shaft
Exterior Panel
Lock Cylinder
KA4 X 25mm Screw
D
2X
Spindle
Lockset
Position Pad
Door
I
M
N
2X
O
2X
P
Q
R
L
Mounting Plate
J
2X
K
2X
KM5 X 10mm Screw
Interior Panel
Battery Cover
Screw Cap Flat Shaft
PM5 X 12mm Screw
Escutcheon Pad
Escutcheon Screw
Cotter Pin
PARTS LIST
KA4 X 25mm Screw(X4)
KM5 X 10mm Screw(X1)
KA4 X 18mm Screw (X2)
Wrench(X1)
Screw Cap(X2) EscutcheonPad(X2)
Positioning Sleeve(X1)
Escutcheon Screw(X2)
Cut at this point when door thickness is
bigger than 40mm and less than 53mm.
Cut at this point when door thickness is
bigger than 53mm and less than 66mm.
Cut at this point when door thickness is
bigger than 66mm and less than 79mm
Cut at this point when door thickness is
bigger than 79mm and less than 92mm.
Cut at this point when door thickness is
bigger than 92mm and less than 105mm.
Position Pad(X2)
Spindle(X2)
Shaft(X1)
Cotter Pin through here
when door thickness is
larger than 70mm
Cotter Pin through here
when door thickness is
less than 70mm
Flat Shaft(X1)
Dust Box(X1)
Cotter Pin(X1)
Strike(X1)
40~120mm Standard Door Thickness
Lock Cylinder(X1)
Cut at this point when door thickness is
bigger than 40mm and less than 55mm.
Cut at this point when door thickness is
bigger than 55mm and less than 70mm.
Cut at this point when door thickness is
bigger than 70mm and less than 85mm
Cut at this point when door thickness is
bigger than 85mm and less than 100mm.
CHU O J
D
Q V
PM5 X 12mm Screw (X2)
N
PM4 X 10mm Screw(X2)
EL
W
K
T S MB
F
KNOW YOUR DOOR
RIGHT IN-SWING DOOR
Make sure the latch throw is
correctly oriented as shown
to fit your right in-swing door
Make sure the pit hole is
correctly oriented as shown.
There are 4 common door-opening directions, the lockset configuration as shown
on each diagram below corresponds to the respective door-opening direction.
RIGHT OUT-SWING DOOR
Make sure the latch throw is
correctly oriented as shown
to fit your right out-swing door
Make sure the pit hole is
correctly oriented as shown.
KNOW YOUR DOOR
LEFT IN-SWING DOOR
Make sure the latch throw is
correctly oriented as shown
to fit your left in-swing door
Make sure the pit hole is
correctly oriented as shown.
LEFT OUT-SWING DOOR
Make sure the latch throw is
correctly oriented as shown
to fit your left out-swing door
Make sure the pit hole is
correctly oriented as shown.
Before installation, determine the door opening direction and adjust the lock
body (latch throw and cylinder), the interior and exterior panels door handles
accordingly. Instructions on how to adjust these parts are provided on the next
pages.
IMPORTANT
HOW TO ADJUST THE LATCH THROW
Here is how to change the latch throw direction. The factory setting of the throw is
for right in-swing door. You do not need to change direction if you have a right
in-swing door.
1. You need a Phillips screwdriver.
4. Fix the strike plate with mounting
screws.
2. Unscrew the strike plate then turn
the latch throw by 180 degree.
3. Turn the latch throw by 180
degree.
HOW TO ADJUST THE CYLINDER
Here is how to change the cylinder direction. The factory setting of the cylinder is
for right in-swing door. You do not need to change direction if you have a right
in-swing door.
the spin
+ is adjusted
to the outside
of the door
The spin can only be slotted in when
the pit hole is at the downside.
3. You must have the cross slot
of the spin facing this side.
4. Fix the strike plate with
mounting screws.
1. You need a Phillips screwdriver.
the spin
current position
of the spin
The spin can only be taken out
when the pit hole is facing down
2. Unscrew the strike plate and take out
the spin as shown then turn it to the
revise side of the lockset.
HOW TO ADJUST THE DOOR HANDLE
W
*The diagram below shows how to shift the door handle from right to left direction.
The factory setting of the handle is for right handed door. You do not need to
change direction if you have a right handed door.
Allen Wrench
3. Lock the two
screws with an
Allen key
2. Exterior Panel: Push the spring
hook upward and hold with your
finger. Then rotate the handle 180°.
Interior Panel: Push the spring hook
downward and hold with your
finger. Then rotate the handle 180°.
1. Remove the two screws
with an Allen key
Make sure your door is prepared for installation. You may need to drill a new
hole. Please use the supplied template for drilling holes required before installa-
tion. You will need some tools or a hole-saw.
Centerline above
1M from ground.
Hole for handle
Hole template
STEP 1: PREPARING YOUR DOOR
H
G
Route the cable inside the door
Make sure the pit hole of
this spin is pointed
downward and facing the
door outside during
installation.
Install the mortise lockset into
door pocket and tighten it with the 4 screws
supplied. Route the cable inside the door pocket and place it aside.
STEP 2: INSTALLING THE LOCKSET
Lockset(1X)
KA4 X 25mm Screw(4X)
Inhaltsverzeichnis
Andere Lockly Türschloss Handbücher
Lockly
Lockly DEADBOLT EDITION SECURE PGD728 Bedienungsanleitung
Lockly
Lockly ACCESS TOUCH PRO Bedienungsanleitung
Lockly
Lockly LATCH EDITION 6S Bedienungsanleitung
Lockly
Lockly SECURE PLUS Bedienungsanleitung
Lockly
Lockly PGD728F Bedienungsanleitung
Lockly
Lockly PRO Bedienungsanleitung
Lockly
Lockly Secure LUX Bedienungsanleitung
Lockly
Lockly LUX COMPACT PGD688F-MB Bedienungsanleitung
Lockly
Lockly DEADBOLT EDITION PGD1128FPW Bedienungsanleitung
Lockly
Lockly LATCH EDITION SECURE PGD628 Bedienungsanleitung
Lockly
Lockly Satin Nickel Secure Plus Smart Lock Deadbols Bedienungsanleitung
Lockly
Lockly DEADBOLT EDITION 7S Bedienungsanleitung
Lockly
Lockly VISION ELITE Bedienungsanleitung
Lockly
Lockly SECURE LUX MORTISE EDITION Bedienungsanleitung
Lockly
Lockly ACCESS TOUCH PRO Bedienungsanleitung
Lockly
Lockly DEADBOLT EDITION PGD1128 Bedienungsanleitung
Lockly
Lockly DEADBOLT EDITION 7S Bedienungsanleitung
Lockly
Lockly Vision Bedienungsanleitung
Lockly
Lockly FLEX TOUCH PRO Bedienungsanleitung
Lockly
Lockly LUX COMPACT PGD688FSN Bedienungsanleitung
