Lockly PGD728F Bedienungsanleitung
DEADBOLT EDITION
INSTALLATION
GUIDE
SECURE
PGD728 | PGD728F | PGD728FC
SECURE
Go to Lockly.com/installation to watch a video
version of this installation guide.
Download the BILT app in the App Store or on
Google Play for step-by-step interactive 3-D
walk-through installation instructions.
OR
Welcome!
This guide will walk you through step-by-step how to
install and get your Lockly Secure up and running.
Installation generally takes less than 30 minutes. If you
have any questions please reference our online sup-
port at: Lockly.com/support or call (669) 500-8835 for
help.
Reference installation parts overview foldout on back page
To complete installation, you would need the following:
Prepare door and remove existing lock. If necessary, use provided
Installation Template to prepare door.
1-⅜" (35mm)
to 2" (50mm)
1" (25mm)
2-⅜" (60mm)
or 2-¾" (70mm)
2-⅛" (54mm)
2
Preparation
Phillips Screwdriver
Flathead Screwdriver
Tape measure or ruler
*Optional
* Use goggles to protect eyes if you need to drill door holes.
ADJUST DEADBOLT AND INSTALL
Step 1
3
1:
Deadbolt slot must align to the center of the door hole. Adjust as shown if needed.
The deadbolt comes set to 2-3/4" (70mm). Adjust length to 2-3/8” (60mm) if necessary.
(wear gloves to protect from possible pinching).
Hold the metal plate and
twist the deadbolt body
clockwise till it snaps to 2-3/8"
Deadbolt comes set at 2-3/4"
(70mm). To return to default,
while deadbolt is extend-
ed, hold the metal plate
and twist the deadbolt body
counter-clockwise till it snaps
to 2-3/4"
Push the crank to
extend the deadbolt
B
B
B
B
A
CC
C
D
D
D
D
A
2-3/4" (70mm)
or 2-3/8” (60mm)
ADJUST DEADBOLT AND INSTALL
4
Step 1
continued
2: Extend the deadbolt by inserting a
flat-head screwdriver into the slot and
turning clockwise.
3: Insert the deadbolt into door edge
hole, make sure that the right side is up
and the slot is in the vertical position.
Secure with 2 screws.
(2X)
K
K
1
2
*This hole (O) is for the optional Slotted Barrel
Extension provided for stabilizing your lock. It
will require drilling extra hole on your door (See
template as provided). Alternatively, you may
use the double-sided adhesive tape provided
which serves the same purpose if you do not
want to drill a hole. If you drilled a hole, securely
tighten the post with a flathead screwdriver
by turning it clockwise before mounting on your
door.
Peel paper off the
Adhesive tape
1: To secure Exterior Assembly of lock, peel the cover off the adhesive strips
INSTALLING THE EXTERIOR ASSEMBLY
Step 2
2: Peel film from adhesive strips and make sure torque blade is in the vertical position with
the deadbolt extended. Place assembly and torque blade through the deadbolt slot and
guide connection cables through the cross-bore hole under the deadbolt as shown. Complete
mounting by aligning and securing until flush to exterior door surface.
EXTERIOR VIEW
(1)
5
Vertical
Extended
Under
B
M
O
4: Use the key to ensure deadbolt locks
and unlocks smoothly (no binding or
rubbing). IMPORTANT: when finished, leave
the deadbolt extended and remove the
key before proceeding to the next step.
2: Align and secure mounting plate with
adhesive strips. Guide connection cables
through the hole and secure to the lower
left notched hole.
INSTALLING THE INTERIOR ASSEMBLY (F)
6
Step 3
(2X)
G
3: Insert and tighten by hand 2
screws located on the left and right of
the blade. Check alignment and
tighten with screwdriver until mounting
plate is securely placed on door.
G
Remove key when finished
Leave deadbolt extended
TIP: when installing screws by hand, turn screws clockwise several turns then
counterclockwise one turn to ensure smooth threading and no cross threading.
1: Check interior mounting plate D
alignment to your door hole before
securing with adhesive strips.
INSTALLING THE INTERIOR ASSEMBLY (F)
7
Step 3
continued
5: Plug the cable coming through mounting plate into the interior assembly as
shown. Tuck cable under eyelet hooks and route to the right on interior assembly .
Plug into , match red side
of plug with red on socket - insert
tightly.
X
X
Y
Y
D F
F
IMPORTANT:
If you need to disconnect this cable, use a
screwdriver to hold down the tab (marked
red) before carefully unplugging. DO NOT
FORCE as this may result in damaging the
lock.
1
2
Install Cable Remove Cable
RESET
PROGRAM
8
INSTALLING THE INTERIOR ASSEMBLY (F)
Step 3
continued
6: Before placing the interior
assembly onto the mounting
plate, ensure the thumb turn
is vertical.
7: Place the interior assembly
against the mounting plate
and make sure the torque
blade is inserted to the thumb
turn shaft.
8: Secure the interior assem-
bly to mounting plate with
2 screws.
Torque Blade Thumb turn shaft
I
2X
I
Align torque blade with thumb
turn shaft, make sure both are in
the vertical position.
RESET
PROGRAM
RESET
PROGRAM
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Lockly Türschloss Handbücher
Lockly
Lockly VISION ELITE Bedienungsanleitung
Lockly
Lockly DEADBOLT EDITION 7S Bedienungsanleitung
Lockly
Lockly LATCH EDITION SECURE PGD628 Bedienungsanleitung
Lockly
Lockly DEADBOLT SECURE PLUS Bedienungsanleitung
Lockly
Lockly DEADBOLT EDITION PGD1128FPW Bedienungsanleitung
Lockly
Lockly MORTISE EDITION SECURE LUX PGD829AFUS Bedienungsanleitung
Lockly
Lockly Satin Nickel Secure Plus Smart Lock Deadbols Bedienungsanleitung
Lockly
Lockly Vision Bedienungsanleitung
Lockly
Lockly DEADBOLT SECURE PLUS Bedienungsanleitung
Lockly
Lockly DEADBOLT EDITION SECURE PGD728 Bedienungsanleitung
Lockly
Lockly Secure LUX Bedienungsanleitung
Lockly
Lockly DEADBOLT EDITION 7S Bedienungsanleitung
Lockly
Lockly ACCESS TOUCH PRO Bedienungsanleitung
Lockly
Lockly FLEX TOUCH Bedienungsanleitung
Lockly
Lockly LATCH EDITION SECURE PLUS Bedienungsanleitung
Lockly
Lockly ACCESS TOUCH PRO Bedienungsanleitung
Lockly
Lockly DEADBOLT EDITION 7S Bedienungsanleitung
Lockly
Lockly FLEX TOUCH Bedienungsanleitung
Lockly
Lockly Secure LUX Bedienungsanleitung
Lockly
Lockly SECURE LUX MORTISE EDITION Bedienungsanleitung
