Lovibond TG 60/268 Montageanleitung

TG 60 / 268

938240 Version 1.0

Operator Instruction Manual

Lovibond® Colour Measurement

Safety Instructions

Attention. The instrument is a safe device. Before operating, please

read the safety instructions and comply strictly with the following

terms to avoid unexpected damage. We shall not be liable for any

damage from incorrect operation.

Battery

The instrument contains a built-in battery. Please use the original

one. Do not insert other batteries. This may damage the

instrument.

Do not disassemble, remove or heat the battery.

Once fully charged, please unplug the external power supply.

Please charge the battery every two weeks if the instrument is not

being used to avoid damaging the battery.

For the first three times, please charge the battery fully to ensure it

reaches its optimal state.

External Power Source

Please use the original power adapter to charge the battery to avoid

the chance of shortening the battery life or causing it to explode.

Please unplug the external power source if you are not using the

instrument for some time.

Gloss Meter

Do not use the instrument in an inflammable or explosive

environment.

Do not disassemble the instrument which may cause damage or an

explosion.

Please stop using the instrument if you smell something burning.

Send it back to the repair centre.

Table of Contents

Safety Instructions .............................................................................................. 2

Table of Contents................................................................................................ 3

1.0 Introduction.................................................................................................. 4

2.0 External Features .......................................................................................... 6

3.0 Operating Instruction.................................................................................... 7

3.1 Turn on/off ..................................................................................................... 7

3.2 Calibration......................................................................................................8

3.3 Measurement............................................................................................... 10

3.4 Connecting to PC.......................................................................................... 17

3.5 Printing.........................................................................................................18

4. System Function Description......................................................................... 18

4.1 Data Management....................................................................................... 18

4.2 Mode Selection............................................................................................. 24

4.3 Mode Parameter.......................................................................................... 24

4.4 Angle Selection............................................................................................. 29

4.5 Tolerance Settings........................................................................................ 29

4.6 Function Setting ...........................................................................................30

5. Routine Maintenance.................................................................................... 31

5. Technical Specifications ................................................................................ 32

6. Sales Offices.................................................................................................. 33

1.0 Introduction

The gloss meter complies to IS0 2813 (International Standard).

The gloss meter features a large, interactive touch screen and QC

software. It is easy to use, stable in its performance and accurate

in measurement

Advantages

1. Large touch screen (3.5inch), high resolution (480*320), full-view

display.

2. Complies with ISO 2813, ASTM D 523, GB/T 9754 standards.

3. Aesthetic design perfectly combined with ergonomics structure.

4. Three measurement angles (20°, 60°, 85°) can measure

simultaneously (multi angle gloss meter).

5. Three operating modes, multi-function settings.

6. QC software with powerful extending function.

7. Input standard data manually, easy to operate.

8. High hardware configuration with multiple innovative

technologies.

9. Auto power-off function to save electricity consumption.

Cautions

The gloss meter is a precise measuring instrument. Please avoid

dramatic change of external environment when measuring. Those

changes include the flickering of light, a rapid change in

temperature and / or humidity.

Keep the instrument balanced. Make sure the measuring aperture is

held tight to the test sample, and do not shake or shift it when

measuring. Please prevent the gloss meter from any knocks or

bangs. This instrument is not water-proof. Do not use it in an

environment of high humidity or mist.

Keep the instrument clean. Avoid dust, powder or solid particles

entering the measuring aperture and accessories.

After use, please turn off. Keep the instrument and calibration

plate in the instrument case.

Users may not make any changes to the instrument without

permission since that may affect the measuring accuracy or even

damage the instrument.

2.0 External Features

LCD Screen: Touch Screen Display to

measure data and instrument

settings. Switch/Measure

button: Press

LCD Screen: Displays measurement data and instrument navigation

buttons.

Switch/Measure Button: Press the button for 3 seconds to turn the

gloss meter on and off. Press the button quickly to take a

measurement.

Indicator Light: When turning on, this displays green. After start-up,

the light turns off. When power is low or the instrument is charging,

it will display a red light. Fully charged will show green.

USB interface: The instrument automatically recognizes the

connection status. The USB interface is used to transfer data to a

PC. It can also be used to connect the power adapter to a computer

to charge the gloss meter (specification: 5V, 2A). The RS-232

interface is used to connect to the printer.

Protective Cover (Calibration plate): This protects the measuring

aperture. The built-in calibration plate is used for instrument

calibration.

Note: To separate the protective cover from the instrument, refer to

LCD Screen

Switch /

Measure Button

Protective Cover

(Calibration Plate)

Indicator Light

RS 232 /

USB Interface

Figure 1: Features

Figure 2. Hold the instrument with one hand, and remove the cover

by gently pulling the “Open” mark. You only need to separate it

from one side. Do not separate it from two sides.

Figure 2: Separation Method

3.0 Operating Instruction

3.1 Turn on/off

Press the switch button for 3 seconds to turn on the instrument.

The LCD screen will display the boot logo. After a few seconds, it

will automatically enter into the measurement interface as shown in

Figure 3. Press the switch button again for 3 seconds, the

instrument will turn off.

Figure 3: Standard Mode Measurement

3.2 Calibration

In the screen shown in Figure 3, click “Menu” to the main menu as

shown in Figure 4.

Select “Calibrate” to enter into Calibration mode as shown in Figure

Back

Note: The single angle

gloss meter does not

have this selection

option. The substitute

option is basic mode

average measurement

Figure 4: Main Menu

Figure 5: Sub-menu Interface for Calibration

3.2.1 Calibration

Click “Calibrate”, it will remind you to install the calibration plate.

Make sure the calibration plate is installed correctly on the

instrument. Click “OK” or press the measurement button to start

calibration.

If the instrument is being used in an unstable environment (such as

extreme or variable temperatures, altitude and humidity), a

calibration must be carried out.

In order to ensure accuracy, always use the original standard plate

for calibration. Any dust on the standard plate will affect the

accuracy of the calibration. Keep the standard plate clean. The

standard plate is a precise optical component. Please do not leave it

under strong lights. Environmental factors will have an effect on the

gloss value of the standard plate over time. It is therefore

recommended that it is returned to the factory or a qualified local

National Institute of Metrology for calibration yearly.

Note:The SN (serial number) corresponds to the internal number of

the instrument. In the calibration interface, it will show the

“Calibration Plate Number”. It is important to note this if you are

working with more than one gloss meter.

3.2.2 Change Calibration Values

Click “Change Cal. Values”. The user can select between “Change

20° cal. Value”, “Change 60° cal. Value” and “Change 85° cal. Value.”

Note: Extreme caution should be taken when operating in this

menu. It is normally recommended that these values should be

modified by the manufacturer or a qualified metrology institute.

These calibration values only need to be modified when they differ

from the values of the actual calibration plate. Before modifying,

please back up the original values.

3.3 Measurement

The instrument has three measurement modes: “Basic Mode”,

“Statistical Mode” and “Continuous Mode”. These can be selected

in the Main Menu per Figure 6.

Basic Mode: This is a basic test that provides a single measurement.

The results will be saved automatically each time. This data can be

used as the standard in Statistic Mode. It can display 5 sets of test

data simultaneously.

Statistical Mode: This provides a statistical evaluation and can

measure a single sample multiple times. If the “difference” switch is

selected, it displays the variance to the sample standard.

Continuous Mode: Continuous measuring times can be set to 99.

Interval times can also be selected. When the “Test” button is

pressed, the instrument will start to measure automatically

according to the settings.

Figure 6: Mode Selection

Inhaltsverzeichnis

Andere Lovibond Messgerät Handbücher

Lovibond

Lovibond SD 60 Bedienungsanleitung

Lovibond

Lovibond Scuba II Bedienungsanleitung

Lovibond

Lovibond SD 400 Oxi L Bedienungsanleitung

Lovibond

Lovibond SD 400 Oxi L Bedienungsanleitung

Lovibond

Lovibond PFXi 195 Montageanleitung

Lovibond

Lovibond Photometer-System MD100 Bedienungsanleitung

Lovibond

Lovibond Photometer-System MD100 Bedienungsanleitung

Lovibond

Lovibond MD200 Bedienungsanleitung

Lovibond

Lovibond Scuba II Bedienungsanleitung

Lovibond

Lovibond MD200 Bedienungsanleitung

Lovibond

Lovibond RT300 Bedienungsanleitung

Lovibond

Lovibond MD200 Bedienungsanleitung

Lovibond

Lovibond EC 2000 Gardner Montageanleitung

Lovibond

Lovibond SensoDirect Oxi200 Bedienungsanleitung

Lovibond

Lovibond PM 620 Bedienungsanleitung

Lovibond

Lovibond SensoDirect pH200 Bedienungsanleitung

Lovibond

Lovibond CheckitDirect Bedienungsanleitung

Lovibond

Lovibond Tintometer MD100 Bedienungsanleitung

Lovibond

Lovibond Tintometer XD 7500 Bedienungsanleitung

Lovibond

Lovibond Fx Montageanleitung

Lovibond

Lovibond SD 300 pH Bedienungsanleitung

Lovibond

Lovibond MD200 Bedienungsanleitung

Lovibond

Lovibond Maxi Direct Bedienungsanleitung

Lovibond

Lovibond Scuba+ Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung