LRS Butler XP Betriebsanleitung

Installation, Warranty and Service Information

Long Range Systems, Inc.

4550 Excel Parkway, Suite 200

Addison, TX 75001

800.437.4996 •www.pager.net

SERVICE

www.pager.net

Butler XP

PROGRAMMING GUIDE

Table Of Contents

Launch Butler XP Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Read Butler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Configuring a Button Butler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Button Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

System ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Group Paging Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Beep Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Secondary Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Cancel Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Low Battery Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Repaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Stop Re-Paging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Save a Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Load an Existing Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Programming Pagers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Group Pagers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Long Range Systems 1Button Butler Program Guide

Launch Butler XP Application

Auto Run

1. Insert the CD into the PC drive, program will Auto-run.

2. Follow the Installation Wizard.

3. Once installation is complete, click on the Windows Start menu.

4. Select All Programs.

5. Select Beach Butler.

6. Select Butler Configurations Utility.

7. The Butler XP configurations screen will display.

Manual Install

1. In the event the program does not automatically run on the PC:

2. Insert the CD into the PC drive.

3. Use Windows Explorer to explore the CD drive.

4. Run the Setup program

5. Proceed with the installation wizard

6. Once installation is complete, click on the Windows Start menu.

7. Select All Programs.

8. Select Beach Butler.

9. Select Butler Configurations Utility.

10. The Butler XP configurations screen will display.

Long Range Systems 2Button Butler Program Guide

Read Butler

This feature reads the current configuration settings of the Butler. Unit Serial Number and current Firmware

Version will display in the bottom right.

1. Connect one end of the USB cable to the PC.

2. Connect the other end of the USB cable to the Butler XP. The USB connection is located in the

Butler XP’s battery compartment. (Batteries are not required for programming).

3. Press the Read Butler button.

Long Range Systems 3Button Butler Program Guide

Configuring a Button Butler

Note: The Butler XP must be connected to the PC using the USB cable before configuration. .

• A configuration can be modified from a previously saved file, or manually created on screen.

• For any changes to take affect press the Update

• The Update Butler button must be pressed for changes to be applied.

Button Setup

The Button section is used to set the message sent to the pager when the “Service” button on the Butler XP

is pressed.

To set a Message:

1. Under PAGER, enter the pager number that the “Service” button will page.

2. Under MESSAGE, enter the message to be sent to the pager.

3. From the MODE drop down box, select an alert mode.

Note: Firmware versions prior to 1.11 will only support “Mode” set to DEFAULT

Butler ID

The Butler ID is used to identify which Butler unit the service request came from.

Example: If the Butler ID is “5”, and the message is set to “Service”, then the pager message will dis-

play “Service 5”.

To set the Butler ID:

1. Enter the Butler ID number 1 to 9999.

System ID

Note: The System ID should be changed ONLY when interference occurs because of other LRS systems in nearby areas.

Default System ID is 0.

In the event that more than one LRS system is in close geographical proximity, the system ID can be changed

to avoid interference. If the System ID is changed, the System IDs of all pagers also need to be changed (up-

dated) to the same System ID. (See Programming Pagers pg. 11)

Long Range Systems 4Button Butler Program Guide

To set System ID:

1. From the System ID drop down box, select the ID number to use.

2. Click the Update Butler button to save the settings.

3. Reprogram pagers used with the system (refer to Programming Pagers on pg. 10).

Group Paging Enable

Group Paging allows you to page 2 or more pagers at the same time. You must program the pagers in the

same group. (See Programming Pagers on pg. 13)

To enable Group Paging:

When group paging is enabled, pager numbers 1-99 will be used to page a “group”. (See p. 10 to con-

figure Group Paging settings)

Beep Enable

This feature will enable or disable the Butler from beeping when the “Service” button is pressed, and when

the USB connection is made.

To set Beep:

Under Beep, click on the Enabled check box to enable or disable (a check mark indicates beep is en-

abled).

Long Range Systems 5Button Butler Program Guide

Secondary Paging

The Secondary Paging feature, when enabled, will send a message to a second pager after the third repage

cycle. This feature is useful if you want a backup person to respond to a customer’s request if the first per-

son does not.

Example: Set Message to “Aisle”, and Butler ID to “15”. During repage, the main pager will display

“Aisle 15”. After the third repage, the secondary pager will display “Aisle 15”.

To set Seconday Paging:

1. Enable and set Repaging (see p. 8).

2. Under Secondary Page, click on the Enabled check box to enable or disable (a check mark indicates

secondary page is enabled).

3. From the PAGER drop down box, select the pager number that will receive the secondary page.

Note: If the Repage (p. 8) feature is enabled, the transmitter will repage the main pager at pre-set intervals until

the page is cleared. (See Stop Re-paging, p. 8 for instructions on clearing the page).

Cancel Message

Note: Secondary Paging must be enabled (see p. 7).

This feature will enable or disable sending a preset cancel message to pagers when a magnet resets the But-

ton Butler.

Example:

IF: 1. Butler ID is set to “15”

2. Cancel message is set to “Cancel”

3. Butler is set to send message “Aisle” to the main pager

4. “Service” button on Butler is pressed

5. Pager displays “Aisle 15”

6. The pager magnet is held over the “Service” button and repaging is stopped (see p. 11)

THEN: The secondary pager will display “Cancel Aisle 15”.

If the page is stopped/canceled after the Secondary Pager goes off, the Secondary Pager will receive “Can-

cel Aisle 15”. This is useful if using more than one pager, so the second person is notified.

Long Range Systems 6Button Butler Program Guide

Long Range Systems 7Button Butler Program Guide

To set Cancel Message:

1. Click on the Enabled check box to enable or disable (a check mark indicates input is enabled.)

2. Enter a message.

Low Battery Page

This sends a message to the pager to add new batteries.

1. Under Low Battery Page, click on the Enabled check box to enable or disable (a check mark indi-

cates low battery page is enabled).

2. Enter the pager number this will alert.

3. Enter a message. Once set, the function automatically alerts the selected pager when the batter-

ies get low.

Example:

IF: Butler XP with ID of 5 has low batteries

THEN: Pager will display “Low Battery 5”

Repaging

This feature will enable or disable the re-paging feature. When the “Service” button is pressed, the Butler

transmitter will resend the message to the pager (at pre-set time intervals) until the page is cleared.

To set Re-paging:

1. Click on Enabled box to enable or disable (a check mark indicates input is enabled).

2. Enter a Repage time. Must be 10 seconds or more.

Stop Re-paging

To stop repaging, hold the pager magnet over the Service button for 1 second. User will hear a beep to in-

dicate repaging has ended.

Save a Configuration

This feature allows the user to store a read or modified configuration from Button Butlers. File will save to

a .b2c extension. To save a Configuration:

1. Select File, Save Configuration.

2. Enter file name, select destination, and Save.

Responded

www.pager.net

www.buttonbutler.com

SERVICE

“BEEP”

Long Range Systems 8Button Butler Program Guide

Hold magnet

over circled area

to stop repaging.

Load an Existing Configuration

This feature allows the user to load a preset configuration to Button Butlers. To Load:

1. Select File, Load Configuration.

2. Select configuration file and Open.

3. Press Update Unit (USB cable must be attached to the Button Butler).

Programming Pagers

Note: Before programming a pager, make sure the pager is turned OFF.

The Button Butler does not operate with Star Pagers.

Long Range Systems 9Button Butler Program Guide

Inhaltsverzeichnis

Andere LRS Sender Handbücher

LRS

LRS T9550 LCK Bedienungsanleitung

LRS

LRS TX-7471-C232 Bedienungsanleitung

LRS

LRS T7400A Bedienungsanleitung

LRS

LRS TX-9560MT Handbuch

LRS

LRS T7450A Bedienungsanleitung

LRS

LRS T9601 Bedienungsanleitung

LRS

LRS Table Genie Technisches Datenblatt

LRS

LRS Butler II TX-1605-5 Betriebsanleitung

LRS

LRS Freedom Bedienungsanleitung

LRS

LRS T7470 Bedienungsanleitung

LRS

LRS Butler II Bedienungsanleitung

LRS

LRS Freedom T7460 Bedienungsanleitung

LRS

LRS TX-9561EZ Bedienungsanleitung

LRS

LRS T9550 LCK Bedienungsanleitung

LRS

LRS T74C232 Bedienungsanleitung

LRS

LRS TX-7471-C232 Bedienungsanleitung

LRS

LRS TX-9601 Bedienungsanleitung

LRS

LRS T7400A Bedienungsanleitung

LRS

LRS T9550 LCM Bedienungsanleitung

LRS

LRS T9601 Bedienungsanleitung

LRS

LRS T7503 Bedienungsanleitung

LRS

LRS TX-7470-C232 Bedienungsanleitung

LRS

LRS T7400A Bedienungsanleitung

LRS

LRS Freedom TX-7470 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung