Lutron Electronics GRAFIK Eye QS Betriebsanleitung

Model Numbers: QSGRJ-6E, QSGRJ-8E, QSGRJ-16E

QSGR-6E, QSGR-8E, QSGR-16E

120 V~

50/60 Hz 220 - 240 V~

50/60 Hz

Unit Capacity (watts) 2000 W 3000 W

MLV 2000 VA

1600 W 3000 VA

2400 W

Zone Capacity (watts) 25 – 800 W 40 – 1200 W

MLV 25 – 800 VA

25 – 600 W 40 – 1200 VA

40 – 960 W

See page 6 for EcoSystem bus ratings;

see page 7 for IEC PELV/NEC®Class 2 ratings.

For California residents only:

The batteries in these devices contain Perchlorate Material –

special handling may apply.

For more information visit

www.dtsc.ca.gov/hazardouswaste/perchlorate

LUTRON

with EcoSystem

Control Unit Quick Installation and

Operation Guide

Please Read

Contents

Features and Functions of the GRAFIK Eye QS Control Unit ....2

Wiring the GRAFIK Eye QS Control Unit

Overview of Line Voltage/Mains and EcoSystem Wiring .......... 3

Line Voltage Wiring Details.................................. 4

EcoSystem Bus Wiring Details............................... 6

Overview of IEC PELV/NEC®Class 2 Wiring .................... 7

QS Link Control Wiring Details............................... 8

Power Group Wiring Example ............................... 9

Completing Installation of the GRAFIK Eye QS Control Unit ....10

Programming Mode

Entering and Exiting Programming Mode ..................... 11

Navigating Menus in Programming Mode ..................... 11

Wireless Mode.......................................12

FCC Information ......................................... 12

Zone Setup

Assigning Load Types..................................... 13

Assigning Non-Dim Load Type.............................. 13

Setting Load Types....................................... 14

EcoSystem Setup

Building the System ...................................... 15

Assigning/Unassigning an EcoSystem Device to a Zone......... 16

Scene Setup

Setting Zone Levels, Fade Rates, and Shade Group Actions ..... 17

Sensor Setup .......................................18

Scene Mode ............................................ 19

Configuring Occupancy Sensor Settings (optional) ............. 20

Pico Wireless Control Setup:

Associating with a GRAFIK Eye QS Wireless Control Unit........ 21

Troubleshooting .....................................22

Troubleshooting: EcoSystem Functions ..................23

Warranty ...........................................24

Contact Information ..................................24

For additional features and advanced functions, see the

complete installation and operation guide at www.lutron.com/qs

The GRAFIK Eye QS with EcoSystem control unit allows for

control of both lights and shades, without interfaces, using a

single control unit. Features include pushbutton scene recall,

info screen that displays energy savings and status, IR receiver,

astronomic timeclock, contact closure input, and engravable

backlit buttons that are easy to find and operate. The built-in

EcoSystem bus link can control up to 64 EcoSystem devices.

English Español Français

12345691011 12 13 14 7815 16

9-16

1-8

Info screen

Displays status or

programming functions

Scene buttons

With integral scene

indicator LEDs

Optional Shade

button groups

Preset and raise/lower

buttons with integral LEDs

(maximum of 3 button

groups)

Zone numbers

Zone raise/lower buttons

Zone LEDs display current

lighting zone levels

Timeclock button

Displays current

timeclock info

OK button

Used for programming

Infrared receiver

For handheld remote use

Master buttons

Temporarily raise and lower

lighting levels on unit

USB type mini B

For programming via PC

{

Hinged faceplate

Features and Functions of the GRAFIK Eye QS with EcoSystem Control Unit

Note: Zones 1, 2, and 3 are

integral line voltage dimming

zones that can control line

voltage loads. Remaining zones

are EcoSystem zones only.

Zones 1, 2, and 3 can be either

EcoSystem zones or line voltage

zones (no zone can be both)

Page button

Switches between displaying

zones 1 to 8 and 9 to 16 on

16-zone unit

Note: 6-zone control unit will show only zones 1 through 6.

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye QS with EcoSystem Control Unit Quick Installation and Operation Guide 2

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye QS with EcoSystem Control Unit Quick Installation and Operation Guide 3

Wiring the GRAFIK Eye QS with EcoSystem Control Unit:

Overview of Line Voltage/Mains and EcoSystem Wiring

12 AWG (4.0 mm2)

each terminal

120 V~

220 - 240 V~

Distribution

Panel

Line Voltage/Mains

Cables and Load Wiring

To additional

EcoSystem devices

EcoSystem Bus Wiring

(See the bus wiring details section for

complete specification)

Two 16 AWG (1.5 mm2)

each terminal

EcoSystem devices: LED

drivers, interfaces, or ballasts

Two E1 and two E2 connections are

provided for ease of wiring, and to

provide two connecting points; there is

only one EcoSystem link on the unit.

Note: Ballasts and other EcoSystem

devices must NOT obtain power from a

line voltage output on the GRAFIK Eye

QS with EcoSystem control unit.

Distribution

Panel

Dimmable LED bulb*

Load controlled

by power module

or interface

Terminal labels:

L: Hot/Live

N: Neutral

: Ground

1, 2, 3: Dimmed/Switched

line voltage outputs

Power module

or interface

* For a complete list of approved dimmable LEDs

please call 1.800.523.9466 or visit

www.lutron.com/dimcflled

Wiring the GRAFIK Eye QS with EcoSystem Control Unit:

Line Voltage Wiring Details

• Useproperlycertifiedcableforallline

voltage/mains cables.

• Propershort-circuitandoverload

protection must be provided at the

distribution panel. You can use up to a

20 A circuit breaker for your installation.

• Installinaccordancewithalllocaland

national electrical codes.

• IECPELV/NEC®Class 2 terminals may

be temporarily unplugged for ease of IR,

occupancy sensor, and control wiring.

• Notice: Risk of damage to unit. Do not

connect line voltage/mains cable to IEC

PELV/NEC®Class 2 terminals.

Step 1: Install wallbox. Mount a 3½in

(89 mm) deep 4-gang U.S. wallbox on a

dry, flat indoor surface that is accessible

and allows for system programming and

operation. Allow at least 4½in (110 mm)

clearance above and below the faceplate

to ensure proper heat dissipation. Allow

1 in (25 mm) for faceplate overhang on

all sides.

Note: 4-gang wallbox available from

Lutron;P/N241400.

Step 2: Test load wiring.

• TurnpowerOFFatthecircuitbreakeror

fuse box.

• Connectastandardlightswitchbetween

the live lead and load wire to test the

circuit.

• TurnpowerONandcheckforshortor

open circuits. If load does not operate,

the circuit is open. If the circuit breaker

trips (fuse blows or opens), a load short

may exist. Correct short or open circuits

and test again.

Step 3: Check control unit wiring.

•Earth/ground terminal connection must

be made as shown in line voltage wiring

diagrams.

•Do not mix different load types on the

same zone.

• Follow all local and national electrical

codes when installing IECPELV/NEC®

wiring with line voltage/mains wiring.

WARNING! Shock hazard. May

result in serious injury or death.

Always turn off circuit breaker or

remove main fuse from power line

before doing any work. Before

connecting the loads to the

GRAFIK Eye QS with EcoSystem

control unit, test the loads for

short-circuits.

(continued on next page)

Neutral

Hot/Live Switch

Load

LUTRON

Faceplate overhangs

wallbox on all sides;

allow 1 in (25 mm)

4`in

(110 mm)

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye QS with EcoSystem Control Unit Quick Installation and Operation Guide 4

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye QS with EcoSystem Control Unit Quick Installation and Operation Guide 5

Wiring the GRAFIK Eye QS with EcoSystem Control Unit:

Line Voltage Wiring Details (continued)

Step 4: Connect line voltage and loads

to control unit.

• Strip9in (8 mm) of insulation off the line

voltage/mains cables in the wallbox.

• Connectthelinevoltage/mains,ground,

and load wires to the appropriate

terminals on the back of the control unit.

L: Hot/Live

 N:Neutral

: Ground

Terminals 1, 2, 3: Dimmed/Switched

line voltage outputs

9in

(8 mm)

The recommended installation torque is

5.0 in∙lb(0.6N∙m) for line voltage/mains

connections and 5.0 in∙lb(0.6N∙m) for

the earth/ground connection.

Note: See the zone setup section for a

list of compatible load types and

instructions for programming the

GRAFIK Eye QS with EcoSystem

control unit to properly recognize

them.

Notice: Risk of damage to unit. GRAFIK Eye QS with EcoSystem control units must

be installed by a qualified electrician in accordance with all applicable regulations

and building codes. Improper wiring can result in damage to control units or other

equipment.

Note: To avoid overheating and possible damage to equipment, do not install control

units to dim receptacles, motor-operated appliances, or fluorescent lighting not

equipped with Lutron Hi-lume, Eco-10, Tu-Wire, EcoSystem electronic dimming

ballasts, or other EcoSystem devices approved for your location. In dimmed magnetic

low-voltage circuits, you can prevent transformer overheating and failure by avoiding

excessively high current flow. Do not operate control units with any lamps removed

or burned out; replace any burned out lamps immediately; use only transformers that

incorporate thermal protection or fused primary windings. Control units are designed for

residential and commercial use, for indoor use only.

EcoSystem bus wiring may be considered

NEC®Class1orIECPELV/NEC®Class

• NEC®Class 1: EcoSystem bus wiring

may be run in the same conduit as mains

voltage wiring to fixtures.

• IECPELV/NEC®Class 2: EcoSystem bus

wiring must be separated from all mains

and NEC®Class 1 wiring.

• Consult applicable national and local

codes for compliance.

• Lutronrecommendsusingtwodifferent

colors for E1 and E2 (EcoSystem bus)

wires. This will prevent wiring mistakes

in junction boxes where several different

EcoSystem bus wires combine. Use

the following instructions for wiring the

EcoSystem bus.

• EachEcoSystem link can have only 1

GRAFIK Eye QS with EcoSystem control

unitconnectedtoit.Noadditional

EcoSystem bus supplies can be on the

link.

• Upto64EcoSystem devices can be

connected to the EcoSystem link.

• Nootherdevicesmaybeconnectedto

the EcoSystem link.

WARNING! Shock hazard. May

result in serious injury or death.

Do not wire live. Interrupt power

via circuit breaker before wiring

and servicing the EcoSystem bus

supply.

Step 1: Use the wire size chart at right to

determine which wire size to use based

on the length of the EcoSystem bus.

Step 2: Wire the EcoSystem bus from

terminal E1 and terminal E2 to all

EcoSystem devices.

Step 3: If wiring the EcoSystem bus as

IECPELV/NEC®Class 2, maintain proper

separation from mains and NEC®Class 1

wiring.

Step 4: Turn on circuit breaker to

energize.

EcoSystem Bus

18 V-250 mA

Wiring the GRAFIK Eye QS with EcoSystem Control Unit:

EcoSystem Bus Wiring Details

Wiring Size and Bus Length

EcoSystem bus wires E1 and E2 are not

polarity sensitive. EcoSystem bus length

is limited by the wire gauge used for E1

and E2 as follows:

Wire Gauge Maximum EcoSystem

Bus Length

12 AWG

(4.0 mm2)2200 ft (671 m)

14 AWG

(2.5 mm2)1400 ft (427 m)

16 AWG

(1.5 mm2)900 ft (275 m)

18 AWG

(1.0 mm2)570 ft (175 m)

Note: Some EcoSystem devices

(ballasts, drivers, and interfaces)

accept connections to daylight

sensors and occupancy sensors.

For instructions on installing and

operating these devices, refer to

their individual instruction sheets.

EcoSystem bus wiring cables (16 AWG/

1.5 mm2) are available from Lutron, part

numbers C-CBL-216-GR-1 (non-plenum)

and C-PCBL-216-CL-1 (plenum).

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye QS with EcoSystem Control Unit Quick Installation and Operation Guide 6

Contact Closure Input Wiring

24 V-50 mA

For settings, see the full installation

and operation guide at

www.lutron.com/qs.

12 ABC

NH123456

1234

ABC

123456LN

1234

ABC

123456LN

Note: Use appropriate wire connecting devices

as specified by local codes.

Example:

Occupancy sensor

(maximum 1)

1: COM

2: 24 V-*

3: MUX

4: MUX

QS Link Control Wiring

24 V-100 mA

Wiring the GRAFIK Eye QS with EcoSystem Control Unit:

Overview of IEC PELV/NEC®Class 2 Wiring

IR Wiring

From external

IR connection

(by others)

18 AWG (1.0 mm2)

each terminal

18 AWG (1.0 mm2)

each terminal

1: IR DATA

2: IR COM

A: CCI SIG

B: 24 V-

C: CCI COM

To control stations,

shades, or other

GRAFIK Eye QS

control units

Data (terminals 3 and 4):

Twisted, shielded pair 22 AWG (0.5 mm2)

each terminal

Common and power (terminals 1 and 2):

Two 18 AWG (1.0 mm2) each terminal (for link <500 ft/153 m)

Two 12 AWG (4.0 mm2) each terminal (for link 500-2000 ft/153-610 m)

*Do not connect terminal 2

between any GRAFIK Eye QS

control unit and any other power

supply, including another GRAFIK

Eye QS control unit.

See “Power Group Wiring” for a

detailed wiring example.

1234

ABC

123456LN

Example:

Emergency lighting interface (maximum 1)

Note: The GRAFIK Eye QS control unit must

bepoweredbyaNormal/Emergency

distribution panel for proper ELI

operation. Refer to the LUT-ELI-3PH

Installation Guide for the complete

wiring diagram.

A: CCI SIG

B: 24 V-

C: CCI COM

LUT-ELI-3PH

Signal

+V Input

Circuit Common

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye QS with EcoSystem Control Unit Quick Installation and Operation Guide 7

• SystemcommunicationusesIECPELV/NEC®

Class 2 wiring.

• Followalllocalandnationalelectricalcodeswhen

installingIECPELV/NEC®Class 2 wiring with line

voltage/mains wiring.

• Eachterminalacceptsuptotwo18AWG(1.0mm2)

wires.

• Totallengthofcontrollinkmustnotexceed

2000 ft (610 m).

• Makeallconnectionsinthecontrolunit’swallbox.

• WiringcanbeT-tappedordaisy-chained.

• IECPELV/NEC®Class 2 24 V-150 mA.

System Limits

The QS wired communication link is limited to 100

devices or 100 zones.

The GRAFIK Eye QS control unit supplies 3 Power

Draw Units (PDUs) on the QS link. Refer to the

QS Link Power Draw Units specification submittal

(LutronPN369405)formoreinformationconcerning

Power Draw Units.

Wiring the GRAFIK Eye QS with EcoSystem Control Unit:

QS Link Control Wiring Details

QS smart

power

panel

LUTRON

LUTRONLUTRON

LUTRON

T-Tap Wiring Example

GRAFIK Eye QS

with EcoSystem

control unit

Sivoia QS

shade/drape

seeTouch QS

wallstation

To EcoSystem link 1

To EcoSystem

link 2

LUTRON

LUTRONLUTRON

LUTRON

GRAFIK Eye

QS with

EcoSystem

control unit

Sivoia

shade/

drape

seeTouch QS

wallstations

Daisy-Chain Wiring Example

QS smart

power panel

To EcoSystem link 2To EcoSystem link 1

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye QS with EcoSystem Control Unit Quick Installation and Operation Guide 8

Wire Sizes (check compatibility in your area)

QS Link Wiring Length Wire Gauge Lutron Cable Part Number

Less than 500 ft (153 m) Power (terminals 1 and 2)

1 pair 18 AWG (1.0 mm2)GRX-CBL-346S (non-plenum)

GRX-PCBL-346S (plenum)

Data (terminals 3 and 4)

1 twisted, shielded pair 22 AWG (0.5 mm2)

500 to 2000 ft

(153 to 610 m) Power (terminals 1 and 2)

1 pair 12 AWG (4.0 mm2)GRX-CBL-46L (non-plenum)

GRX-PCBL-46L (plenum)

Data (terminals 3 and 4)

1 twisted, shielded pair 22 AWG (0.5 mm2)

Wiring the GRAFIK Eye QS with EcoSystem Control Unit: Power Group Wiring Example

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye QS with EcoSystem Control Unit Quick Installation and Operation Guide 9

On the QS link, there are devices that supply power and devices that consume power. Each device has a speciﬁc number of Power

Draw Units (PDUs) it either supplies or consumes. A Power Group consists of one device that supplies power and one or more

devices that consume power; each Power Group may have only one power-supplying device. Refer to the QS Link Power Draw Units

specificationsubmittal(LutronPN369405)formoreinformationconcerningPDUs.

Within Power Groups on the QS link, connect all 4 terminals (1, 2, 3, and 4), shown by the letter A in the diagram. Between devices on

theQSlinkthatsupplypower,connectonlyterminals1,3,and4(NOTterminal2),shownbytheletterBonthediagram.

Wiring can be T-tapped or daisy-chained.

LUTRON

LUTRON LUTRON

LUTRON

Power Group 1

Power Group 2

Power Group 3

(Do not connect

terminal 2: 24 V-)

(Do not connect

terminal 2: 24 V-)

GRAFIK Eye QS

control unit

Supplies PDUs

QS Power Supply

Supplies PDUs

Energi Savr Node

unit Supplies PDUs

Control Interfaces

Consume PDUs

Control Interfaces

Consume PDUs

Wallstations

Consume PDUs

Wallstations

Consume PDUs

Wallstations

Consume PDUs

QS Sensor Module with

Occupancy Sensor

Consumes PDUs

Connect all 4 terminals within a

power group:

1: Common

2: 24 V-

3 and 4: Data

Connect only 3 terminals

between power groups:

1: Common

3 and 4: Data

Do not connect

Terminal 2: 24 V-

Quantum panel

Supplies PDUs

Completing Installation of the GRAFIK Eye QS Control Unit

1.Mount the control unit in the wallbox as

shown using the four screws provided.

Note: Follow all local and national

electrical codes when installing IEC

PELV/NEC®Class 2 wiring with line

voltage/mains wiring.

2.Verify installation:

•Restore power.

•Press the top scene button. The LED will

light.

•Press the zone raise and lower buttons.

Make sure the control unit is dimming all

connected loads.

3.Apply the protective overlay to the control

unit.

Note: When tightening mounting

screws, make sure that the hinged

cover and faceplate will open fully,

as shown.

Wall

7.9 in

(200 mm)

3.5 in

(87 mm) 3.75 in

(95 mm)

Protective overlay

(apply after installation)

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye QS with EcoSystem Control Unit Quick Installation and Operation Guide 10

Andere Handbücher für GRAFIK Eye QS

Inhaltsverzeichnis

Sprachen:

Andere Lutron Electronics Steuereinheit Handbücher

Lutron Electronics

Lutron Electronics QSN-2DALUNV-S Bedienungsanleitung

Lutron Electronics

Lutron Electronics AuroRA ARMC-5T Gebrauchs- und Pflegehandbuch

Lutron Electronics

Lutron Electronics PowPak Energi TriPak Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics Grafik Eye GRX-4000 Series Montageanleitung

Lutron Electronics

Lutron Electronics Maestro Wireless Pico Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics LQR-WPM-6D Betriebsanleitung

Lutron Electronics

Lutron Electronics QSGRK-3PCE Betriebsanleitung

Lutron Electronics

Lutron Electronics Grafik Eye GRX-4000 Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak RMJ-5R-DV-B Bedienungsanleitung

Lutron Electronics

Lutron Electronics AYFSQ-F Bedienungsanleitung

Lutron Electronics

Lutron Electronics QS Timeclock Betriebsanleitung

Lutron Electronics

Lutron Electronics LCP128 Betriebsanleitung

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-3PD-1 Bedienungsanleitung

Lutron Electronics

Lutron Electronics Vive Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak RMJ-CCO1-24-B Bedienungsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRN-6PCE Betriebsanleitung

Lutron Electronics

Lutron Electronics Vive DFCSJ-OEM-OCC Bedienungsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRJ-3P Betriebsanleitung

Lutron Electronics

Lutron Electronics Stanza SZ-2B Bedienungsanleitung

Lutron Electronics

Lutron Electronics GFS-5E Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak FC-SENSOR Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak RMJS-CCO1-24-B Bedienungsanleitung

Lutron Electronics

Lutron Electronics QS Timeclock Betriebsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRJ-8E Montage- und Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung