Lutron Electronics QSGRK-3PCE Betriebsanleitung

LUTRON

Control Unit

Quick Installation

and Operation Guide

English 中文

Español Italiano

Français Deutsch

Please Read

The GRAFIK Eye®QS control unit allows for control of both lights and window

treatments, without interfaces, using a single control unit. Features include

pushbutton scene recall, info screen that displays energy savings and status,

IR receiver, astronomic timeclock, contact closure input, and engravable backlit

buttons that are easy to find and operate.

Contents

Features and Functions of the

GRAFIK Eye®QS Control Unit .................2

Wiring the GRAFIK Eye®QS Control Unit

Overview of Line Voltage/Mains Wiring. . . . . . . . . 3

Line Voltage Wiring Details. . . . . . . . . . . . . . . . . . . 4

Overview of IEC PELV Wiring. . . . . . . . . . . . . . . . . 6

QS Link Control Wiring Details. . . . . . . . . . . . . . . . 7

Power Group Wiring Example . . . . . . . . . . . . . . . . 8

Completing Installation of the

GRAFIK Eye®QS Control Unit . . . . . . . . . . . . . 9

Programming Mode

Entering and Exiting Programming Mode . . . . . . 10

Navigating Menus in Programming Mode . . . . . . 10

WirelessMode.........................11

Zone Setup

Assigning Load Types. . . . . . . . . . . . . . . . . . . . . . 12

Assigning Non-Dim Load Type. . . . . . . . . . . . . . . 12

SettingLoadTypes........................13

Scene Setup

Setting Zone Levels, Fade Rates,

and Window Treatment Group Actions . . . . . . . 14

Occupancy Sensor Setup . . . . . . . . . . . . . . . . 15

SceneMode .............................16

Configuring Occupancy Sensor Settings

(optional)...............................17

Pico®Wireless Control Setup:

Associating with a GRAFIK Eye®QS

Wireless Control Unit . . . . . . . . . . . . . . . . . . . . . 18

Troubleshooting .......................19

Warranty .............................20

Contact Information . . . . . . . . . . . . . . . . . . . . 20

For additional features and advanced functions,

see the complete installation and operation guide at

www.lutron.com/qs

Model Numbers: QSGRK-3PCE, QSGRK-4PCE, QSGRK-6PCE

QSGRM-3PCE, QSGRM-4PCE, QSGRM-6PCE

QSGR-3PCE, QSGR-4PCE, QSGR-6PCE

All units 230 V 50/60 Hz

QSGRK-3PCE

QSGRM-3PCE

QSGR-3PCE

QSGRK-4PCE

QSGRM-4PCE

QSGR-4PCE

QSGRK-6PCE

QSGRM-6PCE

QSGR-6PCE

Unit Capacity

(watts)

1 500 W 2 000 W 2 300 W

MLV 1 500 VA

1 200 W

2 000 VA

1 600 W

2 300 VA

1 800 W

Zone Capacity

(watts)

40 – 500 W 40 – 500 W 40 – 500 W

MLV 40 – 500 VA

40 – 400 W

40 – 500 VA

40 – 400 W

40 – 500 VA

40 – 400 W

See page 6 for IEC PELV ratings.

Info screen

Displays status or

programming functions

Scene buttons

With integral scene

indicator LEDs

Optional Shade

button groups

Preset and raise/lower

buttons with integral LEDs

(maximum of 3 button

groups)

Zone numbers

Zone raise/lower buttons

Zone LEDs display current

lighting zone levels

Timeclock button

Displays current

timeclock info

OK button

Used for programming

Infrared receiver

For handheld remote use

Master buttons

Temporarily raise and lower

lighting levels on unit

USB type mini B

For programming via PC

{

Hinged faceplate

Features and Functions of the GRAFIK Eye®QS Control Unit

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 2

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 3

Wiring the GRAFIK Eye®QS Control Unit:

Overview of Line Voltage/Mains Wiring

1234

1 2 ABC

123456LN

4.0 mm2each

terminal

230 V

Distribution

Panel

Line Voltage/Mains

Cables and Load Wiring

123456LN

Incandescent load

Load controlled

by power module

or interface

Terminal labels:

L: Hot/Live

N: Neutral

: Ground

1-6: Dimmed/Switched

line voltage outputs

Power module or

interface

Wiring the GRAFIK Eye®QS Control Unit:

Line Voltage Wiring Details

• Useproperlycertifiedcableforallline

voltage/mains cables.

• Propershort-circuitandoverload

protection must be provided at the

distribution panel. You can use up to a

20 A circuit breaker for your installation.

• Installinaccordancewithalllocaland

national electrical codes.

• IECPELVterminalsmaybetemporarily

unplugged for ease of IR, occupancy

sensor, and control wiring.

• Notice: Risk of damage to unit. Do not

connect line voltage/mains cable to IEC

PELV terminals.

Step 1: Install wallbox. Mount an

89mmdeep4-gangU.S.wallboxona

dry, flat indoor surface that is accessible

and allows for system programming

and operation. Allow at least 110 mm

clearance above and below the faceplate

to ensure proper heat dissipation. Allow

25 mm for faceplate overhang on all

sides.

Note:4-gangwallboxavailablefrom

Lutron; P/N 241400.

Step 2: Test load wiring.

• TurnpowerOFFatthecircuitbreakeror

fuse box.

• Connectastandardlightswitchbetween

the live lead and load wire to test the

circuit.

• TurnpowerONandcheckforshortor

open circuits. If load does not operate,

the circuit is open. If the circuit breaker

trips (fuse blows or opens), a load short

may exist. Correct short or open circuits

and test again.

Step 3: Check control unit wiring.

•Earth/ground terminal connection must

be made as shown in line voltage wiring

diagrams.

•Do not mix different load types on the

same zone.

• Follow all local and national electrical

codes when installing IEC PELV wiring

with line voltage/mains wiring.

WARNING! Shock hazard. May

result in serious injury or death.

Always turn off circuit breaker or

remove main fuse from power line

before doing any work. Before

connecting the loads to the

GRAFIK Eye®QS control unit, test

theloadsforshort-circuits.

Neutral

Hot/Live Switch

Load

LUTRON

Faceplate overhangs

wallbox on all sides;

allow 25 mm

110 mm

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 4

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 5

Wiring the GRAFIK Eye®QS Control Unit:

Line Voltage Wiring Details (continued)

Step 4: Connect line voltage and loads

to control unit.

• Strip8mmofinsulationofftheline

voltage/mains cables in the wallbox.

• Connectthelinevoltage/mains,ground,

and load wires to the appropriate

terminals on the back of the control unit.

L: Hot/Live

N: Neutral

: Ground

 Terminals1-6:Dimmed/Switched

line voltage outputs

8 mm

The recommended installation torque

is0.6N∙m for line voltage/mains

connectionsand0.6N∙m for the earth/

ground connection.

Note: See the zone setup section for

a list of compatible load types and

instructions for programming the

GRAFIK Eye®QS control unit to properly

recognize them.

Notice: Risk of damage to unit. GRAFIK Eye®QS control units must be installed by

a qualified electrician in accordance with all applicable regulations and building codes.

Improper wiring can result in damage to control units or other equipment.

Note: To avoid overheating and possible damage to equipment, do not install control

unitstodimreceptacles,motor-operatedappliances,orfluorescentlightingnot

equippedwithLutronHi-lume®,Eco-10®,Tu-Wire®, electronic dimming ballasts, or

otherdevicesapprovedforyourlocation.Indimmedmagneticlow-voltagecircuits,

youcanpreventtransformeroverheatingandfailurebyavoidingexcessivelyhighcur-

rent flow. Do not operate control units with any lamps removed or burned out; replace

any burned out lamps immediately; use only transformers that incorporate thermal

protection or fused primary windings. Control units are designed for residential and

commercial use, for indoor use only.

1234

1 2 ABC

123456LN

Contact Closure Input Wiring

24 V 50 mA

For settings, see the full installation

and operation guide at

www.lutron.com/qs

1 2 ABC

NH123456

1234

1 2

ABC

123456LN

1234

1 2

ABC

123456LN

Note: Use appropriate wire connecting

devices as specified by local

codes.

Example:

Occupancy sensor

(maximum 1)

1: COM

2: 24 V *

3: MUX

4: MUX

QS Link Control Wiring

Wiring the GRAFIK Eye®QS Control Unit:

Overview of IEC PELV Wiring

IR Wiring

From external

IR connection

(by others)

1.0 mm2each

terminal

1.0 mm2each terminal

1: IR DATA

2: IR COM

A: CCI SIG

B: 24 V

C: CCI COM

To control

stations, window

treatments, or

other GRAFIK Eye®

QS control units

Data (terminals 3 and 4):

Twisted, shielded pair 0.5 mm2each terminal

24 V 100 mA

Common and power (terminals 1 and 2):

Two 1.0 mm2each terminal (for link <153 m)

Two 4.0 mm2eachterminal(forlink153-610m)

*Do not connect terminal 2

between any GRAFIK Eye®QS

control unit and any other power

supply, including another GRAFIK

Eye®QS control unit.

See “Power Group Wiring” for a

detailed wiring example.

1234

1 2

ABC

123456LN

Example:

Emergency lighting interface (maximum 1)

Note: The GRAFIK Eye®QS control unit

must be powered by a Normal/

Emergency distribution panel for

proper ELI operation. Refer to the

LUT-ELI-3PHInstallationGuidefor

the complete wiring diagram.

A: CCI SIG

B: 24 V

C: CCI COM

LUT-ELI-3PH

Signal

+V Input

Circuit Common

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye®QSControlUnitQuickInstallationandOperationGuide6

• SystemcommunicationusesIECPELVwiring.

• Followalllocalandnationalelectricalcodeswhen

installing IEC PELV wiring with line voltage/mains

wiring.

• Eachterminalacceptsuptotwo1.0mm2wires.

• Totallengthofcontrollinkmustnotexceed

610m.

• Makeallconnectionsinthecontrolunit’swallbox.

• WiringcanbeT-tappedordaisy-chained.

• IECPELV24V 150 mA.

System Limits

The QS wired communication link is limited to 100

devices or 100 zones.

The GRAFIK Eye®QS control unit supplies 3 Power

Draw Units (PDUs) on the QS link. Refer to the

QS Link Power Draw Units specification submittal

(LutronPN369405)formoreinformationconcerning

Power Draw Units.

Wiring the GRAFIK Eye® QS Control Unit:

QS Link Control Wiring Details

QS smart

power

panel

LUTRON LUTRON LUTRON

LUTRON

T-Tap Wiring Example

GRAFIK Eye®QS

control unit

Sivoia®QS

window

treatment

seeTouch®QS

wallstation

LUTRON LUTRON LUTRON

LUTRON

GRAFIK Eye®QS

control unit

Sivoia®

window

treatment seeTouch®QS

wallstations

Daisy-Chain Wiring Example

QS smart

power panel

GRAFIK Eye®QS

control unit

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 7

Wire Sizes (check compatibility in your area)

QS Link Wiring Length Wire Gauge Lutron Cable Part Number

Less than 153 m Power (terminals 1 and 2)

1 pair 1.0 mm2GRX-CBL-346S (non-plenum)

GRX-PCBL-346S (plenum)

Data (terminals 3 and 4)

1 twisted, shielded pair 0.5 mm2

153 to 610 m Power (terminals 1 and 2)

1 pair 4.0 mm2GRX-CBL-46L (non-plenum)

GRX-PCBL-46L (plenum)

Data (terminals 3 and 4)

1 twisted, shielded pair 0.5 mm2

Wiring the GRAFIK Eye®QS Control Unit: Power Group Wiring Example

On the QS link, there are devices that supply power and devices that consume power. Each device has a specic number of Power

Draw Units (PDUs) it either supplies or consumes. A Power Group consists of one device that supplies power and one or more

devicesthatconsumepower;eachPowerGroupmayhaveonlyonepower-supplyingdevice.Refer to the QS Link Power Draw Units

specificationsubmittal(LutronPN369405)formoreinformationconcerningPDUs.

Within Power Groups on the QS link, connect all 4 terminals (1, 2, 3, and 4), shown by the letter A in the diagram. Between devices on

the QS link that supply power, connect only terminals 1, 3, and 4 (NOT terminal 2), shown by the letter B on the diagram.

WiringcanbeT-tappedordaisy-chained.

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 8

LUTRON

Power Group 1

Power Group 2

Power Group 3

(Do not connect

terminal 2: 24 V )

(Do not connect

terminal 2: 24 V )

GRAFIK Eye®QS

control unit

Supplies PDUs

QS Power Supply

Supplies PDUs

Energi Savr NodeTM

unit Supplies PDUs

Control Interfaces

Consume PDUs

Control Interfaces

Consume PDUs

Wallstations

Consume PDUs

Wallstations

Consume PDUs

Wallstations

Consume PDUs

QS Sensor Module with

Occupancy Sensor

Consumes PDUs

Connect all 4 terminals

within a power group:

1: Common

2: 24 V

3 and 4: Data

Connect only 3 terminals

between power groups:

1: Common

3 and 4: Data

Do not connect

Terminal 2: 24 V

Quantum®

Supplies PDUs

Completing Installation of the GRAFIK Eye®QS Control Unit

1.Mount the control unit in the wallbox as

shown using the four screws provided.

Note: Follow all local and national

electrical codes when installing IEC

PELV wiring with line voltage/mains

wiring.

2.Verify installation:

•Restore power.

•Press the top scene button. The LED will

light.

•Press the zone raise and lower buttons.

Make sure the control unit is dimming all

connected loads.

3.Apply the protective overlay to the control

unit.

Note: When tightening mounting

screws, make sure that the

hinged cover and faceplate

will open fully, as shown.

Wall

200 mm

87 mm

95 mm

Protective overlay

(apply after installation)

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 9

Entering and Exiting Programming Mode

Entering programming mode:

Press and hold the top and bottom scene

buttons simultaneously for 3 seconds. The

LEDs in the scene buttons will scroll from

top to bottom, confirming that you are in

programming mode, and the info screen will

display the main menu.

Exiting programming mode:

Press and hold the top and bottom scene

buttons simultaneously for 3 seconds. The

info screen will go to Scene 1.

Navigating Menus in Programming Mode

Master Buttons

The Master buttons allow you to move through the menu

choices. The current choice is highlighted on the info screen.

OK Button

The OK button chooses the current highlighted menu choice.

This will either take you to the next menu or accept a setting you

have selected. When the screen displays a Yes/No question, the

OK button is “Yes”.

Timeclock Button

The Timeclock button functions as a “back” button during

programming mode. Pressing the timeclock button takes you

back one step in the current menu. Pressing it repeatedly

will eventually return you to the main menu, but will not exit

programming mode. When the screen displays a Yes/No

question, the Timeclock button is “No”.

Programming Mode

1 2 3 4 5 6

Press and hold the top and

bottom buttons for 3 seconds

to enter or exit programming

mode

Master buttons

OK button

Timeclock (back) button

Main menu

Scene setup

Timeclock

Scene 1

Fade time

3 seconds

For additional information, see the complete installation and operation guide at www.lutron.com/qs

GRAFIK Eye®QS Control Unit Quick Installation and Operation Guide 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lutron Electronics Steuereinheit Handbücher

Lutron Electronics

Lutron Electronics GRAFIK Eye Architrave GRX-4SLB-DW Bedienungsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRN-6PCE Betriebsanleitung

Lutron Electronics

Lutron Electronics PowPak RMJ-CCO1-24-B Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-3PD-1 Bedienungsanleitung

Lutron Electronics

Lutron Electronics QSGRK-6D Betriebsanleitung

Lutron Electronics

Lutron Electronics Pico QSR4P-3R Bedienungsanleitung

Lutron Electronics

Lutron Electronics LCP128 Betriebsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QS with EcoSystem Betriebsanleitung

Lutron Electronics

Lutron Electronics PowPak FC-SENSOR Bedienungsanleitung

Lutron Electronics

Lutron Electronics TriPak Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak RMJS-16R-DV-B Bedienungsanleitung

Lutron Electronics

Lutron Electronics QS Timeclock Betriebsanleitung

Lutron Electronics

Lutron Electronics Vive Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak Energi TriPak Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics Grafik Eye GRX-4000 Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics AYFSQ-F Bedienungsanleitung

Lutron Electronics

Lutron Electronics RadioRA RA-SBT-CHR Bedienungs- und Sicherheitshinweise

Lutron Electronics

Lutron Electronics LMM-16R-DV-B Bedienungsanleitung

Lutron Electronics

Lutron Electronics Energi Savr Node Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-3PD-1 Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak RMJS-CCO1-24-B Bedienungsanleitung

Lutron Electronics

Lutron Electronics RadioRA RAMC-5W Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak RMJ-5R-DV-B Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro Wireless Pico Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung