Lutron Electronics GRAFIK Eye GRX-4M-GC Montageanleitung

A Step-by-Step Guide for Installing, Operating and Maintaining a Lutron

GRAFIK Eye®AC Motor Group Controller

Please Read Before Installing

Model:

GRX-4M-GC 4 Motor Controller

AC Motor Group Controller

Installer’s Guide

Description

The GRX-4M-GC Group Controller is designed to control

up to four AC motorized window treatments and projection

screens. The Group Controller will control single phase, bi-

directional AC motors (three wire motors: open, close,

neutral). The Group Controller accepts inputs from Lutron’s

GRAFIK Eye®3000 and 4000 Series Controls and also

from controls that provide low-voltage, Class 2, dry contact

closures. The Group Controller has individual motor control

inputs as well as a master control input. This allows

individual control of each motor or control of all motors at

the same time.

Ratings

Input

110–127 V~, 60 Hz Single Phase

20 A maximum input current

Load Capacity

5 A, 1/4 HP motor load per channel @ 120 V~

Table of Contents

Description and Ratings . . . . . . . . . . . . . . . . . . . . . . .2

Important Information . . . . . . . . . . . . . . . . . . . . . . . . .2

System Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Determine a Mounting Location . . . . . . . . . . . . . . . . .4

Pre-installation Motor Wiring Check . . . . . . . . . . . . . .5

Line-Voltage Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Configuring the Motor Direction for

Open and Close Functions . . . . . . . . . . . . . . . . . . . . .7

Setting the Group Controller Address . . . . . . . . . . . .7

Connecting the GRAFIK Eye Communication Link . . .8

Connecting to a GRAFIK Eye 3000 Series Control

Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Connecting multiple Group Controllers to a

GRAFIK Eye 3000 Series Control Unit . . . . . . . . .9

Connecting to a GRAFIK Eye 4000 Series

Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Connecting multiple Group Controllers to a

GRAFIK Eye 4000 Series Control Unit . . . . . . . .10

Verify GRAFIK Eye Control Unit is addressed . . . . .11

Important Information

• Before starting the installation, please completely read

these installation instructions.

• This control must be installed by a certified electrician.

• Install in accordance with all local and national electrical

codes.

• Turn power OFF at circuit breaker or remove fuse

before installing and wiring the controller. Do not wire

with power ON.

• Operating environment should be between 32° F to

104° F (0° C to 40° C).

• Proper short circuit protection and overload protection

must be provided at the distribution panel. You can use

up to a 20 A breaker for your application, where

applicable.

• The Group Controller is only compatible with the

following GRAFIK Eye Control Unit model numbers;

GRX-35xx-x-xx-CPN1622 or GRX-45xx-x-xx-CPN1623.

Setting the load type for a GRAFIK Eye Control

Unit Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Assigning a channel on the Group Controller to

a zone on the GRAFIK Eye Control Unit . . . . . . . . . .12

Contact Closure Input Control Wiring . . . . . . . . . . .13

Setting the Contact Closure Input Type . . . . . . . . . .13

Example of Individual Control

(no dedicated stop input) . . . . . . . . . . . . . . . . . .14

Example of individual Control

(with dedicated stop input) . . . . . . . . . . . . . . . . .15

Example of Master Control

(with dedicated stop input) . . . . . . . . . . . . . . . . .16

Connecting Multiple Group Controllers . . . . . . .17

Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

LUTRON

12345

COM1

CLOSE1

STOP1

OPEN1

OPEN1 CLOSE1 OPEN2 CLOSE2 OPEN3 CLOSE3 OPEN4 CLOSE4 OPEN ALL CLOSE ALL

MASTER CONTROLS

PROGRAM

STATUS

POWER

OPTIONS

MS 240V 120V N N C1 O1 N C2 O2 N C3 O3 N C4 O4

COM2

CLOSE2

STOP2

OPEN2

COM3

CLOSE3

STOP3

OPEN3

COM4

CLOSE4

STOP4

OPEN4

COM

STOP

OPEN

System Diagram

AC Motorized

Window

Treatment

GRX-4M-GC Group Controller

Distribution Panel

Class 2/PELV Wiring

Line-Voltage Wiring

Coopersburg, PA 18036 USA

www.lutron.com

Group Controller

GRX-4M-GC

4 MOTOR GROUP CONTROLLER

110-127 V~ 60 Hz

20 A Max. Input Current

LOAD TYPES

Single Phase, Bi-directional Motor

5 A, 1/4 HP per Channel at 120 V~

TYPES DE CHARGES

Phase Simple, Moteur Bidirectionel

5 A, 1/4 HP par Canal a 120 V~

Listed 243C

Ind. Cont. Eq.

Questions? Call Lutron Technical Support

1-800-523-9466 (24 hrs/7 days)

110-127 V~ USA: Class 2

GRAFIK Eye 3000 or 4000 Series

Control Unit

AC Motorized

Window

Treatment

AC Motorized

Window

Treatment

AC Motorized

Projection Screen

Contact Closure Device

(provided by others)

Line-Voltage 3 Wire AC Motor Wiring

3 conductors plus ground

2 conductors

plus ground

Line-voltage input power and

motor power wiring entry Class 2/PELV

wiring entry

Determine a Mounting Location

• Mount unit on a dry, flat indoor surface such as an

electrical closet wall.

• Mount unit in a location that is accessible to allow for

system programming and setup.

• Unit may be mounted in any orientation.

• The unit’s relays will click audibly in normal use. Mount

in a location where this is acceptable.

• The keyholes accept a maximum of 3/16" (5 mm)

mounting bolt. No. 8 (M4) bolt recommended.

• Knockouts are 7/8" (22 mm) in diameter.

12345

PROGRAM STATUS POWER

OPTIONS

Neutral

120V

240V

Motor

Supply

MUX

V+

COM

12345

ADDRESS

ON 4

OPEN ALL

CLOSE ALL

OPEN 4

CLOSE 4

OPEN 3

CLOSE 3

OPEN 2

CLOSE 2

OPEN 1

CLOSE 1

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

9.5 in.

12 in.

6.2 in.

1.25 in.

7.9 in.

2.75 in.

.735 in.

Coopersburg, PA 18036 USA

www.lutron.com

500-9574 Rev. B

Group Controller

GRX-4M-GC

4 MOTOR GROUP CONTROLLER

110-127 V~ 60 Hz

20 A Max. Input Current

LOAD TYPES

Single Phase, Bi-directional Motor

5 A, 1/4 HP per Channel at 120 V~

TYPES DE CHARGES

Phase Simple, Moteur Bidirectionel

5 A, 1/4 HP par Canal a 120 V~

Listed 243C

Ind. Cont. Eq.

Questions? Call Lutron Technical Support

1-800-523-9466 (24 hrs/7 days)

110-127 V~ USA: Class 2

COM

Open

Stop

COM

Open4

Stop4

Close4

COM

Open3

Stop3

Close3

COM

Open2

Stop2

Close2

COM

Open1

Stop1

Close1

Neutral

120 V

Motor

Supply

Jumper

SW Live

Neutral

SW Live

MUX

COM

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

Front View

Side View

Pre-installation Motor Wiring Check

Test your wiring before connecting to the Group Controller.

Use either a momentary, Single Pole Double Throw

(SPDT) switch (as described below) or a motor wiring test

kit (available from Lutron). To order the motor wiring test

kit, contact Lutron at 1-888-SIVOIA1 (1-888-748-6481) and

ask for model 6020086.

Note: If using the motor wiring test kit, please refer to the

instructions provided with the kit.

Danger - Locate and lock the supply breaker in

the OFF position or remove the supply fuse

before working on any circuit.

Testing motor wiring using a SPDT switch:

1. Turn power OFF at circuit breaker (MCB) or remove

fuse.

2. Connect the motor ground wire to earth ground.

Connect earth ground to the ground terminal on the

switch.

3. Connect the motor neutral wire to supply neutral.

4. Using one momentary, Single Pole Double Throw

(SPDT) switch for each motor, connect hot/live to the

common terminal on the switch.

5. Connect one each of the motor power wires to the

output terminals on the switch. Never wire more than

one motor to a switch.

6. Mount switch in a wallbox. Be sure no bare wires or

terminals on the switch are exposed.

7. After verifying it is safe to restore power, turn power

ON.

8. Verify motor will raise/open and lower/close properly. If

necessary, remove power and correct wiring.

Distribution

Panel

Neutrals Earth/Grounds

Hot/Live

Momentary

SPDT Switch

(wallbox not

shown)

AC Motorized

Window

Treatment Shown

Line-Voltage Wiring

Connect line voltage and the AC Motors to the Group

Controller.

12345

PROGRAM STATUS POWER

OPTIONS

Neutral

120V

240V

Motor

Supply

MUX

V+

COM

12345

ADDRESS

ON 4

OPEN ALL

CLOSE ALL

OPEN 4

CLOSE 4

OPEN 3

CLOSE 3

OPEN 2

CLOSE 2

OPEN 1

CLOSE 1

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

GRX-4M-GC Group Controller

AC Motor 1

Motor 4 Power Wires

Motor 3 Power Wires

Motor 2 Power Wires

Motor 1 Power Wires

Power Feed Wiring

Danger - Locate and lock the supply breaker in

the OFF position or remove the supply fuse before

working on any circuit.

• Only connect one motor to each output. Never wire

motors in parallel.

• The Group Controller accepts 110-127 V~, 60 Hz.

• Strip 1/2" of insulation from all power feed and motor

power wires.

• Run power to the Motor Supply Jumper terminal.

Connect the Motor Supply Jumper terminal to the 120 V

Input Voltage terminal using a piece of wire of the same

gauge as the power feed wiring.

• Connect the motor power wires to the appropriate

terminals indicated in the diagram below.

• There is a dedicated earth/grounding block to land the

ground connections for the power feed and each motor.

The recommended tightening torque is 9.0 in-lbs for

line-voltage connections and 10 in-lbs for earth ground

connections.

• Run all power feed and motor power wiring through the

knockout holes on the sides of the unit.

Wiring Detail

Neutral

120V

240V

Motor

Supply

SW Live

Neutral

SW Live

Neutral

Power Feed Wiring

Motor 1 Power Wires SW Live 1B

SW Live 1A

Neutral

120 V Input

Motor Supply Jumper

Wiring Overview

Note: Motor power wire colors may

vary depending on the motor

manufacturer and voltage. Refer to

the motor manufacturer’s instructions

for more detailed wiring information.

Earth/Grounding

Block

Coopersburg, PA 18036 USA

www.lutron.com

500-9574 Rev. B

Group Controller

GRX-4M-GC

4 MOTOR GROUP CONTROLLER

110-127 V~ 60 Hz

20 A Max. Input Current

LOAD TYPES

Single Phase, Bi-directional Motor

5 A, 1/4 HP per Channel at 120 V~

TYPES DE CHARGES

Phase Simple, Moteur Bidirectionel

5 A, 1/4 HP par Canal a 120 V~

Listed 243C

Ind. Cont. Eq.

Questions? Call Lutron Technical Support

1-800-523-9466 (24 hrs/7 days)

110-127 V~ USA: Class 2

COM

Open

Stop

COM

Open4

Stop4

Close4

COM

Open3

Stop3

Close3

COM

Open2

Stop2

Close2

COM

Open1

Stop1

Close1

Neutral

120 V

Motor

Supply

Jumper

SW Live

Neutral

SW Live

MUX

COM

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

AC Motor 2 AC Motor 3 AC Motor 4

Ground *

* Motor earth/ground wire is not shown in

this diagram. See Wiring Detail below.

Wiring entry knockouts

12345

PROGRAM STATUS POWER

OPTIONS

MUX

V+

COM

12345

ADDRESS

ON 4

OPEN ALL

CLOSE ALL

OPEN 4

CLOSE 4

OPEN 3

CLOSE 3

OPEN 2

CLOSE 2

OPEN 1

CLOSE 1

Operate the

channel using the

Open and Close

buttons

18036 USA

500-9574 Rev. B

ntroller

CONTROLLER

rrent

rectional Motor

annel at 120 V~

RGES

eur Bidirectionel

nal a 120 V~

43C

t. Eq.

n Technical Support

rs/7 days)

USA: Class 2

COM

Open

Stop

COM

Open4

Stop4

Close4

COM

Open3

Stop3

Close3

COM

Open2

Stop2

Close2

COM

Open1

Stop1

Close1

MUX

COM

Change the

desired channel’s

output direction by

switching the

corresponding

Options switch

Configuring the Motor Direction for the

Open and Close Functions

For each Channel of the unit, the motor’s direction of

rotation needs to be configured for the Open and Close

functions so that the AC Motor will move in the proper

direction. This is accomplished using the Options

Switches, #1 through #4. This step needs to be performed

whether each channel is controlled individually or all

channels are controlled together.

1. Restore power to unit. Once the appropriate line

voltage and motor connections have been made to the

unit, replace the cover on the line voltage wiring

compartment. Remove the cover from the Class 2

wiring compartment. Turn power back ON.

2. Determine AC motor position. Determine whether

the AC Motor that is controlled by Channel 1 is open

or closed. If it is open, press the Close 1 manual

override button. If it is closed, press the Open 1

manual override button. If the AC Motor moves to the

desired position, the Channel is configured properly.

Proceed to Step 4. If the AC Motor does not move to

the desired position, proceed to Step 3.

3. Verify motor movement. If the AC Motor did not

move to the desired position in the prior step, slide the

Options Switch #1 to the opposite position. Press the

same button again that was pressed in Step 2 (Open

or Close). If the AC Motor moves to the desired

position Channel 1 is now configured properly.

Proceed to Step 4.

4. Repeat for remaining motors. Repeat Steps 2 and 3

for the rest of the Channels that are connected to AC

Motors. Options Switch #2 configures Channel 2,

Options Switch #3 configures Channel 3, and Options

Switch #4 configures Channel 4.

Note: Do not change the position of Options Switch #5.

This switch is used to change the contact closure input

type. See section Setting the Contact Closure Input Type

on page 12 for more details on the Options Switch #5.

Setting the Group Controller Address

Each Group Controller must have a unique address to

enable it to communicate with the GRAFIK Eye Control

Units. You can have a maximum of eight (8) units on the

link (combined total of Group Controllers, and SG-SVC

controls).

The Group Controller address is set using the Address

switch.

Note: The Group Controller occupies one of eight shade

control addresses. These eight shade control addresses

are in addition to the GRAFIK Eye system address limits

(8 Control Units and 16 Accessory Controls/Wallstations).

12345

Address Switch Settings

Connecting the GRAFIK Eye®Communication

Link

The Group Controllers may be connected to the GRAFIK

Eye system communication link to control the AC motors.

The Group Controller also provides power for up to three

GRAFIK Eye 4000 Series Control Units or accessory

controls.

• Up to 8 Group Controllers or other motorized window

treatment controls may be added to the GRAFIK Eye

communication link.

•GRAFIK Eye system communication link wiring requires

that all controls be daisychained.

• Control wiring shown must not be run in the same

raceway as line (mains) voltage wiring.

• Total communication link wiring length is not to exceed

2,000 ft. (450 m for 2.5 mm2wiring). Refer to the

GRAFIK Eye Installers Guide for more detailed

information.

• Shielding must be connected at each junction, but not

earth grounded.

GRX

Dimming

Panel

GRX

Dimming

Panel

GRX Control

Unit

GRX Control

Unit

GRX

Wallstation

GRX

Wallstation

GRX Group

Controller

GRX

Wallstation

GRX Group

Controller

To other Group Controllers,

GRAFIK Eye dimming panels,

Control Units, or Wallstations.

Correct wiring technique (daisychain wiring) Incorrect wiring technique (branch or homerun wiring)

12345

PROGRAM STATUS POWER

OPTIONS

MUX

V+

COM

12345

ADDRESS

ON 4

OPEN ALL

CLOSE ALL

OPEN 4

CLOSE 4

OPEN 3

CLOSE 3

OPEN 2

CLOSE 2

OPEN 1

CLOSE 1

Zone 4

Zone 6

Hot/Live

SSA

CU WIRE ONLY

Zone 2

1 2 3 4

Zone 3

Zone 5

Neutral

Zone 1

USA

CLASS 2

IEC

PELV

Connecting to a GRAFIK Eye 3000 Series Control Unit

Connect only the COM, MUX and

MUX terminals from the Group

Controller to the GRAFIK Eye

Control Unit. Do not connect the

+V terminals together.

GRX-4M-GC Group Controller

Rear view of a GRAFIK Eye 3000 Series Control Unit

Recommended cable: Lutron part number GRX-CBL-346S-

4 conductor Class 2/PELV Wiring

Terminal 1: One #18 AWG or larger

Terminal 2: Do not connect.

Terminals 3 and 4: One twisted pair #18 AWG or larger

COM

MUX

12345

PROGRAM STATUS POWER

OPTIONS

Neutral

120V

240V

Motor

Supply

MUX

V+

COM

12345

ADDRESS

ON 4

OPEN ALL

CLOSE ALL

OPEN 4

CLOSE 4

OPEN 3

CLOSE 3

OPEN 2

CLOSE 2

OPEN 1

CLOSE 1

12345

PROGRAM STATUS POWER

OPTIONS

Neutral

120V

240V

Motor

Supply

MUX

V+

COM

12345

ADDRESS

ON 4

OPEN ALL

CLOSE ALL

OPEN 4

CLOSE 4

OPEN 3

CLOSE 3

OPEN 2

CLOSE 2

OPEN 1

CLOSE 1

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

Zone 4

Zone 6

Hot/Live

SSA

CU WIRE ONLY

Zone 2

1 2 3 4

Zone 3

Zone 5

Neutral

Zone 1

USA

CLASS 2

IEC

PELV

Connecting multiple Group Controllers to a GRAFIK

Eye 3000 Series Control Unit

The GRAFIK Eye system communication link wiring

requires that all controls be daisychained. One control gets

connected to another in series. Up to 8 Group Controllers

or other motorized window treatment controls may be

added to the GRAFIK Eye communication link.

To additional Group

Controllers (up to a total

of 8 maximum)

Recommended cable: Lutron part number GRX-CBL-346S-

4 conductor Class 2/PELV Wiring

Terminal 1: One #18 AWG or larger

Terminal 2: Do not connect.

Terminals 3 and 4: One twisted pair #18 AWG or larger

431

ersburg, PA 18036 USA

lutron.com

500-9574 Rev. B

oup Controller

RX-4M-GC

TOR GROUP CONTROLLER

27 V~ 60 Hz

Max. Input Current

D TYPES

e Phase, Bi-directional Motor

/4 HP per Channel at 120 V~

ES DE CHARGES

e Simple, Moteur Bidirectionel

/4 HP par Canal a 120 V~

Listed 243C

Ind. Cont. Eq.

ons? Call Lutron Technical Support

523-9466 (24 hrs/7 days)

-127 V~ USA: Class 2

COM

Open

Stop

COM

Open4

Stop4

Close4

COM

Open3

Stop3

Close3

COM

Open2

Stop2

Close2

COM

Open1

Stop1

Close1

MUX

COM

Coopersburg, PA 18036 USA

www.lutron.com

500-9574 Rev. B

Group Controller

GRX-4M-GC

4 MOTOR GROUP CONTROLLER

110-127 V~ 60 Hz

20 A Max. Input Current

LOAD TYPES

Single Phase, Bi-directional Motor

5 A, 1/4 HP per Channel at 120 V~

TYPES DE CHARGES

Phase Simple, Moteur Bidirectionel

5 A, 1/4 HP par Canal a 120 V~

Listed 243C

Ind. Cont. Eq.

Questions? Call Lutron Technical Support

1-800-523-9466 (24 hrs/7 days)

110-127 V~ USA: Class 2

COM

Open

Stop

COM

Open4

Stop4

Close4

COM

Open3

Stop3

Close3

COM

Open2

Stop2

Close2

COM

Open1

Stop1

Close1

MUX

COM

Coopersburg, PA 18036 USA

www.lutron.com

500-9574 Rev. B

Group Controller

GRX-4M-GC

4 MOTOR GROUP CONTROLLER

110-127 V~ 60 Hz

20 A Max. Input Current

LOAD TYPES

Single Phase, Bi-directional Motor

5 A, 1/4 HP per Channel at 120 V~

TYPES DE CHARGES

Phase Simple, Moteur Bidirectionel

5 A, 1/4 HP par Canal a 120 V~

Listed 243C

Ind. Cont. Eq.

Questions? Call Lutron Technical Support

1-800-523-9466 (24 hrs/7 days)

110-127 V~ USA: Class 2

COM

Open

Stop

COM

Open4

Stop4

Close4

COM

Open3

Stop3

Close3

COM

Open2

Stop2

Close2

COM

Open1

Stop1

Close1

MUX

COM

1010

12345

PROGRAM STATUS POWER

OPTIONS

MUX

V+

COM

12345

ADDRESS

ON 4

OPEN ALL

CLOSE ALL

OPEN 4

CLOSE 4

OPEN 3

CLOSE 3

OPEN 2

CLOSE 2

OPEN 1

CLOSE 1

CU WIRE ONLY

USA

CLASS 2

IEC

PELV

SSA RTN

DO NOT USE

SSA

1 IN, OUT

2 IN, OUT

4 IN

3 IN

4 OUT

3 OUT

Connecting to a GRAFIK Eye 4000 Series Control Unit

GRX-4M-GC Group Controller

Rear view of a GRAFIK Eye 4000 Series Control Unit

Recommended cable: Lutron part number GRX-CBL-46L

4 conductor Class 2/PELV Wiring

Terminals 1 and 2: Two #12 AWG

Terminals 3 and 4: One twisted/shielded pair #18 AWG

Note: #12 AWG wire will not fit in the Group Controller terminal blocks. Use a #18 AWG

wire to connect to the Group Controller terminal block as shown. This extra piece of wire

(pig tail) cannot exceed 6 inches.

12345

PROGRAM STATUS POWER

OPTIONS

Neutral

120V

240V

Motor

Supply

MUX

V+

COM

12345

ADDRESS

ON 4

OPEN ALL

CLOSE ALL

OPEN 4

CLOSE 4

OPEN 3

CLOSE 3

OPEN 2

CLOSE 2

OPEN 1

CLOSE 1

12345

PROGRAM STATUS POWER

OPTIONS

Neutral

120V

240V

Motor

Supply

MUX

V+

COM

12345

ADDRESS

ON 4

OPEN ALL

CLOSE ALL

OPEN 4

CLOSE 4

OPEN 3

CLOSE 3

OPEN 2

CLOSE 2

OPEN 1

CLOSE 1

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

SW Live

Neutral

CU WIRE ONLY

USA

CLASS 2

IEC

PELV

SSA RTN

DO NOT USE

SSA

1 IN, OUT

2 IN, OUT

4 IN

3 IN

4 OUT

3 OUT

Connecting multiple Group Controllers to a GRAFIK

Eye 4000 Series Control Unit

The GRAFIK Eye system communication link wiring

requires that all controls be daisychained. One control gets

connected to another in a series. Up to 8 Group

Controllers or other motorized window treatment controls

may be added to the GRAFIK Eye communication link.

To additional Group

Controllers (up to a total

of 8 maximum)

Coopersburg, PA 18036 USA

www.lutron.com

500-9574 Rev. B

Group Controller

GRX-4M-GC

4 MOTOR GROUP CONTROLLER

110-127 V~ 60 Hz

20 A Max. Input Current

LOAD TYPES

Single Phase, Bi-directional Motor

5 A, 1/4 HP per Channel at 120 V~

TYPES DE CHARGES

Phase Simple, Moteur Bidirectionel

5 A, 1/4 HP par Canal a 120 V~

Listed 243C

Ind. Cont. Eq.

Questions? Call Lutron Technical Support

1-800-523-9466 (24 hrs/7 days)

110-127 V~ USA: Class 2

COM

Open

Stop

COM

Open4

Stop4

Close4

COM

Open3

Stop3

Close3

COM

Open2

Stop2

Close2

COM

Open1

Stop1

Close1

MUX

COM

Coopersburg, PA 18036 USA

www.lutron.com

500-9574 Rev. B

Group Controller

GRX-4M-GC

4 MOTOR GROUP CONTROLLER

110-127 V~ 60 Hz

20 A Max. Input Current

LOAD TYPES

Single Phase, Bi-directional Motor

5 A, 1/4 HP per Channel at 120 V~

TYPES DE CHARGES

Phase Simple, Moteur Bidirectionel

5 A, 1/4 HP par Canal a 120 V~

Listed 243C

Ind. Cont. Eq.

Questions? Call Lutron Technical Support

1-800-523-9466 (24 hrs/7 days)

110-127 V~ USA: Class 2

COM

Open

Stop

COM

Open4

Stop4

Close4

COM

Open3

Stop3

Close3

COM

Open2

Stop2

Close2

COM

Open1

Stop1

Close1

MUX

COM

Recommended cable: Lutron part number GRX-CBL-46L

4 conductor Class 2/PELV Wiring

Terminals 1 and 2: Two #12 AWG

Terminals 3 and 4: One twisted/shielded pair #18 AWG

3 4

persburg, PA 18036 USA

w.lutron.com

500-9574 Rev. B

oup Controller

RX-4M-GC

OTOR GROUP CONTROLLER

127 V~ 60 Hz

Max. Input Current

D TYPES

e Phase, Bi-directional Motor

1/4 HP per Channel at 120 V~

ES DE CHARGES

se Simple, Moteur Bidirectionel

1/4 HP par Canal a 120 V~

Listed 243C

Ind. Cont. Eq.

tions? Call Lutron Technical Support

0-523-9466 (24 hrs/7 days)

0-127 V~ USA: Class 2

COM

Open

Stop

COM

Open4

Stop4

Close4

COM

Open3

Stop3

Close3

COM

Open2

Stop2

Close2

COM

Open1

Stop1

Close1

MUX

COM

See note

below.

Inhaltsverzeichnis

Andere Lutron Electronics Controller Handbücher

Lutron Electronics

Lutron Electronics AYFSQ-F Bedienungsanleitung

Lutron Electronics

Lutron Electronics Energi Savr Node QS QSNE-4S10-D Betriebsanleitung

Lutron Electronics

Lutron Electronics LHD0-96W24V-U UL Bedienungsanleitung

Lutron Electronics

Lutron Electronics Grafik Eye GRX-TVI Bedienungsanleitung

Lutron Electronics

Lutron Electronics seeTouch Bedienungsanleitung

Lutron Electronics

Lutron Electronics QS IR Eye Betriebsanleitung

Lutron Electronics

Lutron Electronics PowPak RMKS-DAL4-SZ Bedienungsanleitung

Lutron Electronics

Lutron Electronics GRX-LC8 Handbuch

Lutron Electronics

Lutron Electronics LHD0-96W24V-U UL Bedienungsanleitung

Lutron Electronics

Lutron Electronics Vive Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics AYFSQ-F Bedienungsanleitung

Lutron Electronics

Lutron Electronics FS-SE Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak FCJ-010 Bedienungsanleitung

Lutron Electronics

Lutron Electronics Hi-lume Premier Bedienungsanleitung

Lutron Electronics

Lutron Electronics YFSQ-F Bedienungsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QS Betriebsanleitung

Lutron Electronics

Lutron Electronics DFCSJ-OEM-OCC Bedienungsanleitung

Lutron Electronics

Lutron Electronics Homeworks QS seeTouch HQWIS-NB-NONE Bedienungsanleitung

Lutron Electronics

Lutron Electronics Sivoia QED Bedienungsanleitung

Lutron Electronics

Lutron Electronics LTEA4U1UKL Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics L3D0-96W24V-U Bedienungsanleitung

Lutron Electronics

Lutron Electronics WC-4M-GC Montageanleitung

Lutron Electronics

Lutron Electronics Maestro Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch