Lutron Electronics Grafik Eye GRX-TVI Bedienungsanleitung

Installation and Operation Instructions

Read Before Installing

Please Leave for Occupant

GRX-TVI

Phase Control to 0-10V

Interface Control

Description

The GRX-TVI provides 0-10V control and ballast

switching capabilities in one enclosure. The

interface gives GRAFIK Eye® 3000 Series Control

the ability to control 0-10V ballasts powered by

120V or 277V and provides switching relays that

can handle the in-rush current of a circuit of

ballasts. The interface gives a GRAFIK Eye 3000

Series Control the ability to both dim and switch

electronic ballasts such as Lutron's Eco-10™(TVE

models).

Mounting

• Mount the enclosure vertically on a wall. (See

Mounting Diagram below.)

• Mounting method must be able to support

weight and forces applied during installation.

Installation

NOTE: When interfacing with a GRAFIK Eye 3000

Series Control, a GRX-TVI interface is required for

each fluorescent dimming zone. (Three zone unit

with two fluorescent zones and one incandescent

zone shown as an example.)

Find a suitable location for mounting.

• Look at the System Wiring Layout (below) to

decide on the proper location for the GRX-TVI

(for indoor use only, type1 enclosure).

• The environment where the GRX-TVI is placed

must have an ambient temperature between 32-

104°F (0-40°C).

System Wiring Layout

Mounting Diagram

COOPERSBURG, PA 18036 U.S.A.

0-10V INTERFACE CONTROL

Control Input:

100-120V, 220-240V 50/60Hz

Switches:

100-277VAC

GRX-TVI

Incandescent 16A

Fluorescent 5A

Magnetic Low-voltage 16A

Electronic Low-voltage 16A

Motor 1/4 HP@120V

1/2 HP@277V

GRX-TVI Input Rating

20.02A

20.1A

0-10V Output Rating

Max. 0.3A

Switched Rating

LUTRON LUTRON

GRX-

TVI

Distribution

Panel

Incandescent Zone/Load 3

0-10V Control Fluorescent Zone/Load 1

Switched Fluorescent Zone/Load 2

GRX-3000 Series Control Class 2 Accessory Controls

GRX-

TVI

0-10 Volt Ballast

Ballast

LUTRON

0-10V Control Fluorescent Zone/Load 1

120V or 277V

120V

Four Mounting Holes

Diameter - .25", 6mm Four Screws

Secure Cover

6.10"

155mm

3.30"

84mm

12.50"

318mm Wall

11.75"

298mm

4.0"

102mm

COOPERSBURG, PA18036 U.S.A.

0-10V INTERFACECONTROL

Control Input:

100-120V, 220-240V 50/60Hz

Switches:

100-277VAC

GRX-TVI

Incandescent 16A

Fluorescent 5A

Magnetic Low-voltage 16A

Electronic Low-voltage 16A

Motor 1/4 HP@120V

1/2 HP@277V

GRX-TVI Input Rating

0.02A

0.1A

0-10V Output Rating

Max. 0.3A

Switched Rating

This product may be covered by one or more of the following U.S. patents: 4,797,599;

4,893,062; 5,030,893; 5,191,265; 5,309,068; 5,430,356; 5,463,286; 5,633,540; DES

313,738; DES 344,264; and corresponding foreign patents. U.S. and foreign patents

pending.LutronandGRAFIKEyeareregisteredtrademarksandEco-10isatrademark

of Lutron Electronics Co., Inc.

Product Specifications

Weight 4.25 lb., (2kg)

Input Power Rating 100-120/220-240V 50/60Hz

Mounting Mount on a wall with 4 screws

(Not Provided).

Terminals 2, No. 12-20AWG or 0.5-

2.5mm

conductors per terminal

Environmental 32-104°F (0-40°C)

Output Switching Capacity •Switches 100-277V

Fluorescent ....................... 5A

Incandescent .................. 16A

Low Voltage .................... 16A

Metal Halide .................... 16A

Neon/Cold Cathode ........ 16A

Motor .............. 1/4Hp @ 120V

Motor .............. 1/2Hp @ 240V

0-10V Output Rating 10µA-300mA

GRX-TV1 H

Input Rating 20mA

GRX-TV1 DH

Input Rating 100mA

Regulatory Approval Complies with Standard UL 508

Features • Provides a Class 2 isolated

0-10V output signal that

conforms to EN60929 and

IEC929

• Accepts a constant-gate drive

fluorescent signal. (100-120V,

220-240V, 50/60Hz)

Wiring

• Terminal blocks are rated for two No. 12-

22AWG (0.5-2.5mm2)wires per terminal.

• Strip 3/8" (10mm) of insulation from wires.

• Wiring Diagram A shows a GRX-TVI wired from

one distribution panel. If the power requirement

of the complete system is less than a circuit

breaker rating, one feed can be jumpered inside

the enclosure (As shown).

• Wiring Diagram B shows the GRX-TVI wired

from two separate distribution panels which may

be different phases or voltages.

Wiring Diagram A

3/8"

10mm

100-

120V

220-

240V N2DH2H1N1N1SH1+–

Max 0.3A

0-10V

Control Inputs Load Switched

H2100-

277V

Zone 4

Zone 6

Zone 2

1 2 3 4

Zone 3

Zone 5

Zone 1

GRAY

PURPLE

BLACK

WHITE

NEUTRAL

Distribution

Panel A

GRX-3000

Series Control

GRX-TVI

GROUND

CONNECTIONS

NEUTRAL

0-10 Volt Ballast

GROUND

GRAY

PURPLE

BLACK

WHITE

Hot 2 - 100-120V

Neutral 2

Dimmed Hot

Hot 1

Neutral 1

Switched Hot

0-10 Volt

To additional ballasts

0-10V Control Signal Wires - DO NOT

CONNECT TO LINE VOLTAGE. Lutron is

not liable for damage due to miswiring.

SWITCHED HOT

NEUTRAL

0-10 Volt Ballast

GROUND

LED

SW Hot/Live 2

SSA

Class 2

Neutral

Hot/Live 2

DIMMED HOT

GROUND

HOT 120V

CU WIRE ONLY

SW Hot/Live 1

Hot/Live 1

HOT 120V

Hot 2 - 220-240V

Use 20A Maximum

circuit breaker/MCB

GROUND

• Use the internal terminal block label to see

where to land wires. H2has a 100-120V

connection or a 220-240V connection. Use the

one corresponding to line voltage. The label

shows two separate Hot terminals (H1& H2). H1

is the Hot feed to power the lighting load. H2is

the Hot feed that powers internal circuitry of the

GRX-TVI.

Note 1: Not all terminal blocks receive a

connection.

Note 2: H2must be the same phase as

Dimmed Hot (DH).

•Applies only in the USA: Class 2, 0-10V wiring

must be separated by a barrier from the power

wiring. Enter the Class 2 wires thru the knockout

adjacent to the 0-10V terminal blocks. The

Nomex®barrier is flexible to allow access to the

terminals. The barrier must be in place when

installation is complete.

Important Installation Information

• Install in accordance with all national and local

electrical codes.

• Check for short circuited loads during new

installations before wiring the GRX-TVI.

CAUTION: Multiple feeds may enter this

enclosure. Locate and lock each feed

breaker in the OFF position before

wiring the product.

• Proper short circuit and overload protection

must be provided at the distribution panel. You

can use up to a 20A maximum circuit breaker or

equivalent with adequate short circuit breaking

capacity for your installation.

Legend for Terminal Block Label

(Positioned directly under the terminal blocks)

240V

Power input for GRX-TVI control (220-240V)

120V

Power input for GRX-TVI control (100-120V)

(Only use one input according to Input Voltage)

Neutral for GRX-TVI control

GRAFIK Eye 3000 Series Control Lighting Zone

connection (Phase Control Input to GRX-TVI)

Power input for lighting load

Neutral for lighting load

SH Switched output to power lighting load

+ - 0-10V control signal wires

Diagram shows wiring for 120V

control (100-120V terminal

connection). 220-240V controls

use 220-240V terminal block.

Wiring Diagram B

Operation

After wiring is complete, the unit can be energized

to check for proper operation.

• With the cover removed an LED will provide

visual feedback about the operation of the

system.

• When power is first applied, the LED will turn on

for 8 seconds to indicate start-up mode. The

LED will then start to flash in one of two ways to

indicate the status of the system:

Standard Operation

• The LED will flash at a rate of two pulses per

second to signify proper communication

between the GRAFIK Eye 3000 Series

Control and the GRX-TVI. (The LED will

pulse only twice during the second.)

Incorrect Operation - No Active Input

• The LED will turn on for a second then off for

a second repeatedly to indicate that there is

not an active phase control input to the GRX-

TVI. Check that the phase control dimmer is

on and connected to the GRX-TVI at the

terminal block marked DH2. Check that the

corresponding zone for the DH2terminal is

ON and the light level is not set at the

minimum output.

Zone 4

Zone 6

SW Hot/Live 2

SSA

Zone 2

1 2 3 4

Zone 3

Zone 5

Zone 1

Class 2

Neutral

Hot/Live 2

GRAY

PURPLE

BLACK

WHITE

DIMMED HOT

GRX-TVI

GROUND

CONNECTIONS

GRAY

PURPLE

BLACK

WHITE

Neutral 2

Dimmed Hot

Hot 1

Neutral 1

Switched Hot

0-10V Control Signal Wires - DO NOT

CONNECT TO LINE VOLTAGE. Lutron is

not liable for damage due to miswiring.

HOT 100-277V

Distribution panels can be different phases or voltages

SWITCHED HOT

NEUTRAL

To additional ballasts

0-10 Volt Ballast

GROUND

GRX-3000

Series Control

0-10 Volt

0-10 Volt Ballast

GROUND

LED

CU WIRE ONLY

SW Hot/Live 1

Hot/Live 1

NEUTRAL

HOT 120V

Hot 2 - 100-120V

Hot 2 - 220-240V

Use 20A Maximum

circuit breaker Distribution

Panel A

NEUTRAL

HOT 120V

GROUND

Use 20A Maximum

circuit breaker Distribution

Panel B

NEUTRAL

GROUND

100-

120V

220-

240V N

+–

Max 0.3A

0-10V

Control Inputs Load Switched

100-

277V

• When the LED indicates proper input of a phase

control signal, then output can be checked by

looking at the load and checking operation from

the GRAFIK Eye 3000 Series Control.

• Make sure the GRAFIK Eye 3000 Series

Control is set for Fluorescent Load Type.

(Refer to GRAFIK Eye 3000 Series Installer's

Guide.) If the load type is not set correctly,

proper dimming will not occur.

• For non-dimming ballasts select non-dim load

type and do not connect ballasts to 0-10V

terminals.

Diagram shows wiring for 120V

control (100-120V terminal

connection). 220-240V controls

use 220-240V terminal block.

Lutron Electronics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299 U.S.A.

Made and printed in U.S.A. 11/97 P/N 032-067 Rev. A

Warranty

Lutron warrants each new unit to be free from defects in materials and workmanship

and to perform under normal use and service. This warranty shall run only for a

period of one year from the date of purchase and Lutron's obligations under this

warranty are limited to remedying any defect or replacing any defective part and

shall be effective only if the defective unit is shipped to Lutron postage prepaid

within 12 months after purchase. Damage due to abuse, misuse, inadequate wiring

or insulation is not covered by this warranty.

In no event shall Lutron or any other seller be liable for any other loss or damage,

including consequential or special damages that may arise through the use by a

purchaser or others of this device and the purchaser assumes and will hold

harmless Lutron in respect of all such loss.

Trouble Shooting Guide

Symptom Possible Solution

Cause

0-10 Volt Ballast does not dim Miswire • Verify that LED pulses once per second. If not, check

wiring from phase control unit to the GRX-TVI.

Power is OFF • Make sure the GRAFIK Eye 3000 Series Control is ON.

Miswire • Check proper polarity of 0-10V signals at terminal blocks.

Does it match what is at every ballast? A miswire at any

ballast will cause all ballasts to go to the low end.

Incorrect Control Setup • GRAFIK Eye 3000 Series Control is not configured for

fluorescent load type.

Light does not switch on Miswire • Check that the Switched Hot (SH) connection goes to the

ballasts.

Miswire • Check that the Dimmed Hot (DH) connection is actually

wired to a phase control input.

Light does not switch off Miswire • Load is not connected to Switched Hot (SH) terminal.

Miswire • Check that the Dimmed Hot (DH) connection is actually

wired to a phase control input.

LED is not illuminated No Power Input • Check that power is applied to GRX-TVI unit.

World Headquarters

Lutron Electronics Co., Inc.

7200 Suter Road

Coopersburg, PA 18036-1299 U.S.A.

TOLL FREE: (800) 523-9466 (U.S.A., Canada, and the

Caribbean)

Tel: (610) 282-3800; International 1610 282-3800

Fax: (610) 282-3090; International 1610 282-3090

European Headquarters

Lutron EA LTD

Lutron House

6 Sovereign Close

Wapping

London, E1 9HW England

FREEPHONE: 0800 282107 (U.K.)

Tel: (0171) 702-0657; International 44-171-702-0657

Fax: (0171) 480-6899; International 44-171-480-6899

Technical Assistance

If you have questions concerning the installation or

operation of this product, call the

Lutron Technical

Assistance Hotline

. Please provide exact model

number when calling.

(800) 523-9466 (U.S.A., Canada, and the Caribbean)

Other countries call (610) 282-3800

Fax (610) 282-3090

Our address on the Web is www.lutron.com

UAE, Dubai Sales Office

Tel/Fax: 444-0206; International 971-444-0206

Asian Headquarters

Lutron Asuka Corporation K.K.

3rd Floor

Madre Matsuda Bldg.

4-13, Kioi-cho;

Chiyoda-Ku, Tokyo 102 Japan

TOLL FREE: (0120) 083417 (Japan)

Tel: (03) 3234-1486; International 81-3-3234-1486

Fax: (03) 3234-0167; International 81-3-3234-0167

Hong Kong Sales Office

Tel: 2593-1119; International 852-2593-1119

Fax: 2593-1197; International 852-2593-1197

Andere Handbücher für Grafik Eye GRX-TVI

Andere Lutron Electronics Controller Handbücher

Lutron Electronics

Lutron Electronics DFCSJ-OEM-OCC Bedienungsanleitung

Lutron Electronics

Lutron Electronics LHD0-96W24V-U UL Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak RMKS-DAL4-SZ Bedienungsanleitung

Lutron Electronics

Lutron Electronics Homeworks QS seeTouch HQWIS-NB-NONE Bedienungsanleitung

Lutron Electronics

Lutron Electronics LTEA4U1UKL Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics WC-4M-GC Montageanleitung

Lutron Electronics

Lutron Electronics FS-SE Bedienungsanleitung

Lutron Electronics

Lutron Electronics Energi Savr Node QS QSNE-4S10-D Betriebsanleitung

Lutron Electronics

Lutron Electronics Sivoia QED Bedienungsanleitung

Lutron Electronics

Lutron Electronics PowPak FCJ-010 Bedienungsanleitung

Lutron Electronics

Lutron Electronics QS IR Eye Betriebsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye GRX-4M-GC Montageanleitung

Lutron Electronics

Lutron Electronics YFSQ-F Bedienungsanleitung

Lutron Electronics

Lutron Electronics Hi-lume Premier Bedienungsanleitung

Lutron Electronics

Lutron Electronics LHD0-96W24V-U UL Bedienungsanleitung

Lutron Electronics

Lutron Electronics L3D0-96W24V-U Bedienungsanleitung

Lutron Electronics

Lutron Electronics GRAFIK Eye QS Betriebsanleitung

Lutron Electronics

Lutron Electronics Vive Series Bedienungsanleitung

Lutron Electronics

Lutron Electronics Maestro Bedienungsanleitung

Lutron Electronics

Lutron Electronics seeTouch Bedienungsanleitung

Lutron Electronics

Lutron Electronics GRX-LC8 Handbuch

Lutron Electronics

Lutron Electronics AYFSQ-F Bedienungsanleitung

Lutron Electronics

Lutron Electronics AYFSQ-F Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch