M Design ZINO 700 Bedienungsanleitung

NSTRUCTIONS FOR INSTALLATION AND USE OF

ZINO 700,900,1100

WARNING

: THE SUPLIER TAKES NO RESPONSIBILITY FOR ANY POSSIBLE

DAMAGE, POOR WORKING APPLIANCES AND ACCIDENT AS A RESULT OF INCORRECT

INSTALLATION.

GENERAL

............................................................................

1.1. TRANSPORT AND INSTALLATION

................................

1.2.

FUEL

................................................................................

1.2.1

Recommended fuel: Wood - hard, soft - damp cca 16%

1.2.2 Optimal operation

Recommended fuel: Wood - hard, soft - damp cca 16%

1.2.2 Optimal operation

Recommended fuel: Wood - hard, soft - damp cca 16%

..................................................

1.2

.3 Forbidden fuel

........................................................

1.3 STARTING THE FIRE

......................................................

2. INSTALLATION

................................................................

2.1 ACTIONS TO BE TAKEN UPON INSTALLATION

...

2.2

LIST OF STANDARDS TO BE OBSERVED DURING ASSEMBLY AND OPERATIONS 4

2.3

SAFE DISTANCE FIREPLACE STOVES TYPE „Zino“ FROM FLAMMABLE 5

MATERIALS, LOCATION FIREPLACE STOVES AND SMOKE EXTRACT

2.4

LOCATION the FIREPLACE FURNACE type series „zino“ on the floor 6

2.4.1

REQUIREMENTS FOR PASSING COMBUSTION AIS 6

SECURITY CONDITIONS

.................................................

SUPPLIED ACCESSORIES

.............................................

MAINTENANCE

................................................................

5.1

Method of removal and installation of the deflector plates and pass 9

6. SPECIFICATIONS

.............................................................

6.1 Spare pa

rts

................................................................

6.2 Drawing

.....................................................................

7. Guarantee

.........................................................................

8. Gurantee conditions

........................................................

1 GENERAL

1.1 TRANSPORT AND INSTALLATION

• The ZINO is transported in a horizontal position.

•For facilitate transport you can use a set of solid rubber straps/belts.

Before the installation of ZINO it is necessary to check that the door mechanism functions properly and

that the interior lining of the stove thermal linings are remaining in their correct positions. (see Pic.11

pp.9 )

1.2 FUEL

1.2.1 Recommended fuel: Wood - hard, - dampness approx 16%

The quality of the wood is extremely important for the optimal functioning of the stove /output, clear

glass, etc.../. The idea is to use dried hard wood with moisture content 12% to 18%. Damp wood gives

off less heat, clogs the chimney and the glass of the stove’s door. You can also use compressed wood

briquettes and it is the best to use them in combination with wood also you can use Peat. Damage

as a result of excessive temperature or over firing is not covered under the guarantee; two halves of

woods of the 2kg weight are equal 5-7kW.

1.2.2 Optimal operation

Optimal use of fuel and optimal operation of the stove reach loading approx 1,5kg of wood lying on the

floor of the fire chamber, laid side to side of the combustion chamber. The draught of chimney should

be a minimum of 12 Pa and the regulator set for maximum air supply.

1.2.3 Forbidden fuel

The use of treated wood /painted, etc. / and all types of household waste, which can disperse hazar-

dous gases, is FORBIDDEN and CANCELS OUT ANY CLAIM ON THE GUARANTEE. The use of fluid

fuel /petrol, etc. / is also forbidden.

1.3 STARTING THE FIRE

•

Set regulation at maximum ( see Pic.1 )

• Put a bed of tinder (paper or firelighters) with a little kindling (small twigs or pieces of wood) in the

stove and light the tinder.

NOTE: When a fire is made for the first time, the paint

will harden and that give off smoke and a smell, which

starts after the fire has burned for about 10 minutes and

lasts for about 15 minutes. See to it that there is ample

ventilation in the room. The combustion

chamber should

be kept closed except for fuelling to prevent entry of gases into

the room.

Pic.1

CAUTION:

It is not necessary to overload the fireplace with wood. 1kg dried wood gives a 4kW power.

Example: a fireplace with 80% return gives a power for about 3,2kW for 1kg dry wood. If

you want a power about 6-7kW, it is just enough to put 2kg wood in the fireplace. This is

like two normal pieces of wood. We are not responsible for the bad use of fireplace and any

consequence for not following this guideline. External surfaces of the stove are very hot

during operation, which has to be paid due attention to avoid an accident or burns.

2 INSTALLATION

2.1 ACTIONS TO BE TAKEN UPON INSTALLATION

For your own safety and satisfaction, we advise you to entrust a specialist with the installation.

The appliance has to be installed according to certain prescribes rules and local regulations.

The device must be built in an area with an adequate strength/capacity on the floor boards, which can

spread the weight of the stove. The stove must be positioned so as to maintain the safety distances

from any flammable materials. However, if you decide to carry out the work on your own, we advise

you to do the following:

• Refer to the terms and conditions of our contract of guarantee.

• Ask your supplier for advice.

2.2 LIST OF STANDARDS TO BE OBSERVED DURING ASSEMBLY AND OPERATIONS

The fireplace type „ZINO“complies with STN EN 13229. For installation and operation of the fireplace

type „ZINO“should proceed in accordance with STN 92 0300 „Local fire safety appliances and heat

sources” and STN 73 4201 „The design of chimneys and flues“.

Opening door

Opening

hand

Pic.2

Pic.3

OPEN

WARNING! When connecting chimney from behind so you have to remove the

cap on the chimney shell and the stopper ( see arrow Pic.5 ) and then the stopper fitted to

the top slot, which will remain free to disassembling the chimney.

2.3 SAFE DISTANCE FIREPLACE STOVES TYPE „Zino“ FROM FLAMMABLE MATERI-

ALS, LOCATION FIREPLACE STOVES AND SMOKE EXTRACTION

Appliance type series „ZINO“ must be installed in accordance with Decree MV SR No. 95/2004

statute, coll establishing specifications and requirements for fire safety during installations and

operation of heating appliances, electro thermal appliances and central heating installations

and the constructions and use of chimneys and flues. It is also necessary to respect the STN 73

4210 „Running of the chimneys and flues and connecting fuel appliances. “ The manufacturer re-

commends the installation of the fireplace appliance type series „ZINO“conducted by a Qualified

Professional who is responsible for the materials used for installation, and can issue Certification

for Local Building Control and HETAS Registration. The manufacturer is only responsible for the

delivered product.

Caution: The Installer has to approve the fireplace before the initial operation and

issue a certificate about the safe utilisation and the correct flue gas evacuation

(HETAS Certification)

In the band of radiation ensure that no flammable parts or furniture are allowed up to a distance

of 100cm. due to the radiation of heat from the front of the stove.

The fireplace type series „ZINO“must be installed so that before it left space on the layout, about

1 x 1 m.

The base under appliance type series „ZINO“must be placed on a non combustible material that

will withstand heat stress. Also, all wall and ceiling materials, which the Appliance type series

„ZINO“ may be near must be non combustible materials, respect should also be used for good

thermal insulation.

Combustion pipe must be fitted to the fireplace chimney’s mouthpiece Appliance type series

„ZINO“so that it is firmly and tightly connected.

Combustion pipe can join at the top ( see Pic.4 ) or from behind ( see Pic.5 ). The average of

the flue is 150 mm.

Pic. 4

Pic. 5

Caution: The Installer has to approve the fireplace before the initial operation and

The combustion pipe might be of black respectively stainless steel pipes and elbows. The flue

connection must be made by the shortest route to the flue by STN 73 4210. The combustion pipe

should be implemented and consolidate in order it cannot be released accidentally or spontane-

ously. All fluing should comply with the requirements laid down in Building Regulations Section J.

Connection of the combustion pipe of the Appliance type series „ZINO“can only be to the chimney,

which has been expertly tested. Based on expert examination of the appliance flue connection and

issue a professionally qualified person „Certificated examination on implementation of the chim-

ney, where a professionally qualified person to report state of the chimney and flue for their safe

and reliable operation.

2.4 LOCATION THE FIREPLACE FURNACE TYPE SERIES „ZINO“ON THE

FLOOR

In front of the door, inflammable floors need to be protected by placing the stove on a non combu-

stible material( Stone Glass, Marble, Ceramic Tiles Etc). The hearth needs to project at least 30cm

in front of the door and 30 cm at the sides and back if against a dry lined wall, however if the walls

are constructed of non combustible material ie Brick or stone then a minimum distance of 5cm

should be allowed.

2.4.1 REQUIREMENTS FOR PASSING COMBUSTION AIR

The fireplace furnace type series „ZINO“can be placed directly in the heated respectively outside

the heated space. Every form of combustion uses air. The combustion of fuel uses air from the

area where is the fireplace type series „ZINO“. In case of insufficient ventilation of this area is ne-

cessary to ensure sufficient fresh air from outside the duct can be connected to the inlet throat of

air. ( see Pic.6 )

Pic. 6

3. SECURITY CONDITIONS

In operating the fireplace furnace type series “ZINO” should observe the following pre

cautions:

•The fireplace furnace type series “ZINO” must only be operated by an adult.

•A minimum distance of 80cm clearance to each side and 30cm back of the appliance

must be maintained to avoid flammable parts, furniture and materials.

•The Fireplace type series “ZINO” shall operate under conditions in which a fire or explo

sion.

•Comply with fire regulations of general application.

•When operating the fireplace furnace type series “ZINO” the body temperature of the stove ri-

ses which if touched would cause serious burning. It is therefore prohibited during the operation

of the stove to touch the appliance.

•When operating the fireplace type stoves series “ZINO” the outer surface rises to a very high

temperature in which could cause burns. It is therefore necessary drivers to use the controls

with protective gloves and the auxiliary tools that are included with the fireplace furnace type

series “ZINO” are used.

•Fire in the fireplace furnace type series “ZINO” must never be extinguish with water.

•The space where it is located fireplace type series “ZINO” must be ensured there is an ade-

quate supply of air for combustion of the fuel.

•Loading doors must be kept closed when running the stove furnace type series “ZINO” always

keep closed when burning except when refuelling.

•They are allowed no interference with the fireplace furnace type series “ZINO” that could en-

danger the safe operation.

•The ignition of fuel in the aggregate is not permitted to use flammable liquids.

•In the event of any problems with the operation of the fireplace furnace type series “ZINO” you

must call the supplier or manufacturer.

•In carrying out the ash pan from the fireplace furnace type series “ZINO” burnt fuel you must

use gloves with sufficient protective property from excessive heat.

4. SUPPLIED ACCESSORIES

•Door opener 1pc ( see Pic.3 )

•Top cap 1pc ( see Pic.7 )

•Operating instructions, guarantee and certificate of quality and completeness of the product

The correct and safe operation of the fireplace furnace type series „ZINO“it is imperative to

observe the operating instructions and installation!!!

Pic.7

5. MAINTENANCE

The customer must regularly clean ashes from an ashtray on a grid /after two full-time heating/

and check whether there is excessive fouling the ash chamber/see ( Pic.8 )

One to two times per heating season /by intensity of use and according to characteristics of the

fuel/ need to check and clean the flue gas path of ash and shoot. Choose to be two deflector

plates. Deflector plate 1: skamol with the stainless holder and deflector refractory plate 2. (see

Pic.11 )

After the cleaning the flue tract and insertion of parts back to its position, check the parts are

properly stored and secured in position so that it could not be a spontaneous change in position of

these parts. ( see Pic.11 )

Pic.11

Pic.8

5.1 Method of removal and installation of the deflector plates and pass

The dismantling of the deflector plate 1:

-Lift plate up / approx 3cm / and remove the stainless steel beam to each slide and push to one

side and a diagonal slide it out of the fireplace.

-Pull the plate to pull himself / approx 4 cm / etc diagonal sway and slide it out of the fireplace.

The dismantling of the pass refractory plate 2:

-Push the plate upwards until it stops at the flue outlet / slide of the plate holders No.1 and No.2

see Pic.12 / clone one side and downward on a diagonal and sliding the plate in the chamber and

then out.

The installation of the pass refractory plate 2:

-Slide-plate on a diagonal into the combustion chamber and to push all the way to the top flue out-

let and insert holders for No.1 and No.2 ( see Pic.12 )

The installation of the deflector plate 1:

-Slide plate on a diagonal to the fireplace stoves and push up and place it on the side facing the

combustion chamber, slide all the way back of the fireplace furnace.

-Stainless steel beam under a diagonal slide into fireplace oven and place it on lateral lines and

then insert the front edge of the plate / make sure that the side holders are well fitted ( see Pic.12

position 1 )

Pic.12

6. SPECIFICATIONS

Identification

of the type of fireplace furnace type

„ZINO“is as follows:

Manufacturer: M-DESIGN BENELUX BVBA

Type : „ZINO......................“,

Usable power range: 3-8kW

Standard: STN EN 13240

„Keep operating instructions”

“The unit can be connected to a common chimney“

“Use only recommended fuels”

The appliance is designed for: Short-term operation

Serial number ( see Pic.10 )

Pic. 10

TYPE

ZINO 700

ZINO 900

ZINO 1100

Rated thermal power ( kW)

4,6

Average efficienty (%)

81,5

80,5

Heat flow into the space (kW)

4,6

Power range (kW)

3-6

3-7

3-8

Flue gas temperature at rated output

(°c)

163

158

152

Avg CO concentration at 13% O2 (%)

0,105

0,11

0,118

The average volume concentration of

CO at 13% O2 ( mg/m³)

1311

1378

1475

Minimum blast (Pa)

The weight of the fireplace furnance

(kg)

130

150

165

Minimum distance from flammable

materials from the flanks and rear

(mm)

200

Minimum distance from flammable

materials from the front (mm)

1000

Fuel delivery interval (h)

Recommanded fuel - dry wood

hardwood like

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere M Design Kamin im Innenbereich Handbücher

M Design

M Design True Vision Series Bedienungsanleitung

M Design

M Design Luna Gold Series Bedienungsanleitung

M Design

M Design VENUS Bedienungsanleitung

M Design

M Design LUNA HC Series Bedienungsanleitung

M Design

M Design Luna Gold 850 V Bedienungsanleitung

M Design

M Design LUNA GOLD 900CL-CR Bedienungsanleitung

M Design

M Design Luna Diamond Series Bedienungsanleitung

M Design

M Design TRUE VISION RUSTICA Bedienungsanleitung

M Design

M Design DIAMOND Gas 550V Bedienungsanleitung

M Design

M Design LUNA DIAMOND 100DH Bedienungsanleitung

M Design

M Design VENUS DHT Bedienungsanleitung

M Design

M Design LUNA 850 V Gold Gas Bedienungs- und Wartungshandbuch

M Design

M Design VENUS GREEN PLUS Series Bedienungsanleitung

M Design

M Design LUNA1300 RD GOLD GAS Bedienungsanleitung

M Design

M Design LUNA 1000 DH Gold Gas Bedienungsanleitung

M Design

M Design LUNA 700H Bedienungsanleitung

M Design

M Design Luna Diamond Series Bedienungsanleitung

M Design

M Design True Vision 1000 RD Bedienungsanleitung

M Design

M Design Venus True Vision Series Bedienungsanleitung

M Design

M Design LUNA GOLD 800DC Leitfaden

M Design

M Design LUNA 700H Bedienungsanleitung

M Design

M Design LUNA 700H Bedienungsanleitung

M Design

M Design TRUE VISION RUSTICA M Leitfaden

M Design

M Design LUNA 850 V Gold Gas Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch