M-system R7L-DA16-R Bedienungsanleitung

EM-7804-F Rev.10 P. 1 / 19

INSTRUCTION MANUAL

DISCRETE INPUT MODULE, 16 points

(LONWORKS)MODEL R7L-DA16

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Discrete input module.........................................................(1)

NeuronID label....................................................................(2)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

LNS Plug-in Software (model: R7LPLG) is usable to set up

Functional Blocks. For detailed information, refer to the

R7PLG Users Manual. The R7LPLG is downloadable at M-

System’s web site: http://www.m-system.co.jp

POINTS OF CAUTION

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V AC rating: 24V ±10%, 50/60 Hz, approx. 70mA

24V DC rating: 24V ±10%, approx. 40mA

■GENERAL PRECAUTIONS

• The unit can acquire 16 points of discrete input, also

pulse input can be acquired up to 8 points out of 16 points.

• When counter pulse and discrete are mixed and acquired,

make sufﬁcient consideration to them.

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■RESTRICTIONS WHEN USING LonMaker3.0 or 3.1

• Operating Environment

Please use LonMaker3.0 under the Environment of LNS3

Service Pack 8 and use LonMaker3.1 under the Environ-

ment of LonMaker3.1 Service Pack 3 or later.

Please use resource ﬁles of LonMark Resource File Ver12

or later.

• LNS Plug-in Software is not usable.

• The network variable of nvoCNTOut (fbCNT) is only

SNVT_count_f.

• When registering a Device on LonMaker, please don’t use

the following items.

External Interface Deﬁnition / Upload From Device

Specify Device Channel / Auto-Detect

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7L-DA16

EM-7804-F Rev.10 P. 2 / 19

COMPONENT IDENTIFICATION

Discrete Input Status Indicator LED

ERR SVCE

ONLINETX/RX

PWR

0123456789ABCDEF

4567

123

10 11 12 13

2341

15 16 17 18

7896

Reset SW Factory Configuration Port

Service SW

Status Indicator LED

LONWORKS, Power Supply

Terminals Input Terminals

■STATUS INDICATOR LED

ID COLOR STAT E MEANING

PWR Green ON Internal 5V is normal

OFF Internal 5V is abnormal.

ONLINE Green

ON Online

Blink

approx.

0.5 Hz

Ofﬂine

Sending/receiving of Net-

work

Variables has stopped.

Blink

approx.

2 Hz

Receiving Wink Message

OFF Abnormal state

ERR Red

ON Writing in the non-volatile

memory

Blink Abnormal state

OFF Normal state

TX/RX Green ON Sending/receiving Network

Variables

OFF Communication is lost.

SVCE Green

ON No network information

Blink

approx.

0.5 Hz

Ofﬂine

Sending/receiving of Net-

work

Variables has stopped.

OFF Normal state

■DISCRETE INPUT STATUS INDICATOR LED

Used to show discrete input signal status.

ON : LED ON

OFF : LED OFF

Note: For ﬁrmware version 0.14 or smaller, when the discrete

inputs are commissioned by LonMaker, the LEDs indi-

cate the status of them.

■SERVICE SWITCH

Used to identify the node in LONWORKS network conﬁgura-

tion.

■RESET SWITCH

Used to reset the Neuron Chip. Press the switch behind the

front cover to reset.

Control functions are halted while completing resetting and

restarting. Conﬁrm no danger before conducting resetting.

■POWER SUPPLY, LONWORKS TERMINAL ASSIGNMENT

NET1

NET2

U (+)

NET1

NET2

V (

–

)

NO. ID FUNCTION, NOTES

1 NET1 LONWORKS communication 1

2 NET2 LONWORKS communication 2

3 FG FG

4 NET1 LONWORKS communication 1

5 NET2 LONWORKS communication 2

6 U (+) Power input

7 V (–) Power input

Note: LONWORKS wiring must be paired between NET1 termi-

nals and/or NET2 terminals.

■INPUT TERMINAL ASSIGNMENT

COM

NO. ID FUNCTION NO. ID FUNCTION

1 COM Common 10 NC No Connection

2 X0 Input 0 11 X1 Input 1

3 X2 Input 2 12 X3 Input 3

4 X4 Input 4 13 X5 Input 5

5 X6 Input 6 14 X7 Input 7

6 X8 Input 8 15 X9 Input 9

7 XA Input 10 16 XB Input 11

8 XC Input 12 17 XD Input 13

9 XE Input 14 18 XF Input 15

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7L-DA16

EM-7804-F Rev.10 P. 3 / 19

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

30 (1.18) [5 (.20)]

DIN RAIL

35mm wide

54 (2.13)

17 (.66)

4567

123

10 11 12 13

2341

15 16 17 18

789

3 (.12)5.5 (.22) 50 (1.97) 18.5 (.73)

115 (4.53)

7–M3 SCREW

TERMINALS

for LONWORKS, POWER

18–M3 SCREW

TERMINALS for INPUT

6 (.24) 6 (.24)

■CONNECTION DIAGRAM

–+–+

COM

■Input Connection Examples

COM

PNP Connection

COM

NPN Connection

V (–)

U (+)

NET2

NET1

NET1 LONWORKS

LONWORKS

EXTENSION CONNECTOR

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7L-DA16

EM-7804-F Rev.10 P. 4 / 19

COMMUNICATION CABLE CONNECTIONS

■HOST PC CONNECTION

HOST PC

LONWORKS

R7L

LONWORKS

R7L

LONWORKS

Terminator

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable.

Applicable wire size: 0.25 to 1.65 mm2(AWG 22 to 16)

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd, Nichifu Co., Ltd

6 (.24) max

3.3 (.13) max

mm (inch)

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7L-DA16

EM-7804-F Rev.10 P. 5 / 19

DEVICE INTERFACE FILE

Device Interface File (XIF) is used to deﬁne a LONWORKS device when programmed on LonMaker.

For this module, the following ﬁle is used:

R7L-DA16v113.XIF

The XIF ﬁles are downloadable at M-System’s web site: http://www.m-system.co.jp

FUNCTIONAL BLOCKS

■NodeObject

NodeObject (Object ID : 0)

nv 0 nviRequest

SNVT_obj_request nv 1 nvoStatus

SNVT_obj_status

nv 2 nvoFileDirectory

SNVT_address

nv 3 nvoABNLCond

SNVT_state

SCPTdirection

SCPTmaxSendTime[ ]

SCPTminSendTime[ ]

SCPTlocation

SCPToemType

SCPTserialNumber

Extension module setting

Maximum sending time (per fb)

Minimum sending time (per fb)

Set Tag No. (name)

Indicate Model No. and Version

Indicate Serial No.

NodeObject :

Network Variables

Configuration Properties

• Network Variables

NETWORK

VARIABLE

TYPE

{ Range }

{ Default }

EXPLANATIONS

nviRequest {SNVT_obj_request} For use with LonMaker and other tools.

nvoStatus {SNVT_obj_status} For use with LonMaker and other tools.

nvoFileDirectory {SNVT_address} For use with LonMaker and other tools.

Required to get access to Conﬁguration Properties.

nvoABNLCond {SNVT_state}

Shows the device status (All 0s in normal conditions).

Bit 0 through Bit 9 : Invalid

Bit 10 : E2PROM Conﬁguration Property check sum error

Bit 11 : E2PROM Count data check sum error

(Bit 10 and Bit 11 can be reset to 0 by RQ_CLEAR_STATUS against NodeObject.)

Bit 12 through Bit 15 : Invalid

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7L-DA16

EM-7804-F Rev.10 P. 6 / 19

• Conguration Properties

CONFIGURATION

PROPERTY

NETWORK

VARIABLE

TYPE

{ Range }

{ Default }

EXPLANATIONS

SCPTdirection ----

{SNVT_state}

{0 or 1}

{0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0}

Bit 0, Bit 1: Setting the extension module (Power supply must

be reset when this conﬁguration property is changed.)

0,0 : Without extension module

1,0 : Discrete input (fb and other settings assigned to the 9th

and following points are invalid with 8-point input module.)

0,1 : Discrete output (fb and other settings assigned to the 9th

and following points are invalid with 8-point output module.)

Set this property before an extension module is connected.

Bit 2 through Bit 15 : Invalid

SCPTmaxSendTime

[Number of fb] ----

{SNVT_time_sec}

{0.0,10.0...3600.0}

{0.0}

Maximum time interval to send network variables (per fb).

(Power supply must be reset when this conﬁguration property

is changed.)

Network variables are sent out in the speciﬁed intervals even

when there is no change in the value.

No sending when a value less than 10.0 is set.

Invalid property when the assigned fb has no network vari-

ables to be sent to the network.

SCPTminSendTime

[Number of fb] ----

{SNVT_time_sec}

{0.0,0.2...3600.0}

{1.0}

Minimum time interval to send network variables (per fb).

(Power supply must be reset when this conﬁguration property

is changed.)

Network variables are sent out in the speciﬁed intervals even

when there are changes in the value faster than the interval.

No sending when a value less than 0.2 is set.

Invalid property when the assigned fb has no network vari-

ables to be sent to the network.

SCPTlocation ----

{SNVT_str_asc}

{30-character string}

{“”}

Used to write Tag No. (name)

SCPToemType ---- {SNVT_str_asc}

{

e.g. “R7L-DA16_VER:0.10”

}Used to indicate Model No. and Version

SCPTserialNumber ---- {SNVT_str_asc}

{e.g. “ZZ123456”} Used to indicate Serial No.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7L-DA16

EM-7804-F Rev.10 P. 7 / 19

■FUNCTIONAL BLOCK: fbCNT [0...7]

fbCNT[0...7] (Object ID : 17...24)

nv 36

...nv 43

nviCNTIn

SNVT_switch

nv 44

...nv 51

nviCNTCtrl

SNVT_switch

nv 52

...nv 59

nvoCNTOut

SNVT_count_32

SNVT_count_f

Set the initial value at nviCNTCtrl at the startup

Set count logic (ON or OFF)

Set operating mode

Set network variable type nvoCNTOut

Set the maximum count

Set the value when fbCNT[ ] is reset

fbCNT[ ] :

SCPTdirection

nviCNTIn :

SCPTinvrtOut

nviCNTCtrl :

SCPTpwrUpState

nvoCNTOut :

SCPTnvType

SCPTmaxRnge

SCPTsetpoint

Network Variables

Configuration Properties

• Network Variables

NETWORK

VARIABLE

TYPE

{ Range }

{ Default }

EXPLANATIONS

nviCNTIn

{SNVT_switch}

{0.0 0}, {100.0 1}, {Invalid}

{0.0 0}

Counted object

nviCNTCtrl

{SNVT_switch}

{0.0 0}, {100.0 1}, {Invalid}

{0.0 0}

Controls operation of fbCNT

0.0 0 : Stop counting

100.0 1 : Start counting

Invalid : Reset count value

nvoCNTOut

{SNVT_count_32}

{0...999 999 999}

{0}

{SNVT_count_f}

{0...999 999}

{0}

Number of ON counts or accumulated time of ON status at nviCNTIn or

the input terminal

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7L-DA16

EM-7804-F Rev.10 P. 8 / 19

• Conguration Properties

CONFIGURATION

PROPERTY

NETWORK

VARIABLE

TYPE

{ Range }

{ Default }

EXPLANATIONS

SCPTdirection ----

{SNVT_state}

{0 or 1}

{0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0}

Bit 0 through 5: Counted object

0,0,0,0,0,0 : nviCNTIn

1,0,0,0,0,0 : X0 1,0,0,0,1,0 : ExX0

0,1,0,0,0,0 : X1 0,1,0,0,1,0 : ExX1

1,1,0,0,0,0 : X2 1,1,0,0,1,0 : ExX2

0,0,1,0,0,0 : X3 0,0,1,0,1,0 : ExX3

1,0,1,0,0,0 : X4 1,0,1,0,1,0 : ExX4

0,1,1,0,0,0 : X5 0,1,1,0,1,0 : ExX5

1,1,1,0,0,0 : X6 1,1,1,0,1,0 : ExX6

0,0,0,1,0,0 : X7 0,0,0,1,1,0 : ExX7

1,0,0,1,0,0 : X8 1,0,0,1,1,0 : ExX8

0,1,0,1,0,0 : X9 0,1,0,1,1,0 : ExX9

1,1,0,1,0,0 : XA 1,1,0,1,1,0 : ExXA

0,0,1,1,0,0 : XB 0,0,1,1,1,0 : ExXB

1,0,1,1,0,0 : XC 1,0,1,1,1,0 : ExXC

0,1,1,1,0,0 : XD 0,1,1,1,1,0 : ExXD

1,1,1,1,0,0 : XE 1,1,1,1,1,0 : ExXE

0,0,0,0,1,0 : XF 0,0,0,0,0,1 : ExXF

ExX0 through ExXF: Extension discrete input

Bit 6: Count function

0 : Number of status changes from OFF to ON

1 : Accumulated time of ON status

Bit 7: Memory storage at the non-volatile memory

0 : Count retained in the memory and preset at the startup

1 : Count always reset to 0

Bit 8 through 15 : Invalid

Minimum input pulse width 500 ms for nviCNTIn, 50 ms

for the input terminals.

DO NOT connect a network variable to nviCNTIn when one

of the input terminals (other than nviCNTIn) is assigned as

the counted object.

ON time per 1 second increments.

SCPTinvrtOut nviCNTIn

{SNVT_lev_disc}

{ST_OFF, ST_ON}

{ST_OFF}

Count logic at nviCNTIn.

ST_OFF : Count with nviCNTIn = ON

ST_ON : Count with nviCNTIn = OFF

SCPTpwrUpState nviCNTCtrl

{SNVT_switch}

{0.0 0}, {100.0 1}, {Invalid}

{100.0 1}

Set value applied at nviCNTCtrl when the power supply is

turned on.

0.0 0 : Stop counting

100.0 1 : Start counting

Invalid : Reset count value

SCPTnvType nvoCNTOut

{SNVT_nv_type}

{}

{SNVT_count_f}

Indicates nvoCNTOut type.

For use with LonMaker and other tools.

SCPTmaxRnge nvoCNTOut

Same as nvoCNTOut.

Default = Max. range value

available for the type

Maximum count for nvoCNTOut. Count reset to 0 and

restarted at overﬂow.

SCPTsetpoint nvoCNTOut

Same as nvoCNTOut.

Default = Max. range value

available for the type

Set value applied at nvoCNTOut when fbCNT[ ] is Over-

Ride.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7L-DA16

EM-7804-F Rev.10 P. 9 / 19

■FUNCTIONAL BLOCK: fbDI[0...7]

fbDI [0...7] (Object ID: 25...32)

nvoDIStat

SNVT_switch

nvoDIArm

SNVT_switch

Network Variables

Configuration Properties

Discrete Input X0, X2, X4, X6,

X8, XA, XC, XE

X1, X3, X5, X7,

X9, XB, XD, XF

Normal Mode Status output at nvoDIStat Status output at nvoDIArm

RS-Flip Flop Mode RS-flip flop set signal

(Set output at nvoDIStat)

Combination Mode Refer to the table in the next page.

RS-flip flop set signal

(Reset output at nvoDIArm)

fbDI [ ] :

SCPTdirection

nvoDIStat :

SCPTinvrtOut

nvoDIArm :

SCPTinvrtOut

Set operating mode

Invert output

nv 60

...nv 67

nv 68

...nv 75

• Input Terminal v.s. fbDI Network Variables (nvoDIStat, nvoDIArm) Assignments

FUNCTIONAL BLOCK NETWORK VARIABLE OUTPUT TERMINAL

fbDI[0] nvoDIStat X0

nvoDIArm X1

fbDI[1] nvoDIStat X2

nvoDIArm X3

fbDI[2] nvoDIStat X4

nvoDIArm X5

fbDI[3] nvoDIStat X6

nvoDIArm X7

fbDI[4] nvoDIStat X8

nvoDIArm X9

fbDI[5] nvoDIStat XA

nvoDIArm XB

fbDI[6] nvoDIStat XC

nvoDIArm XD

fbDI[7] nvoDIStat XE

nvoDIArm XF

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

R7L-DA16

EM-7804-F Rev.10 P. 10 / 19

■FUNCTIONAL BLOCK: fbDI[0...7]

• Network Variables

Normal Mode

NETWORK

VARIABLE

TYPE

{ Range }

{ Default }

EXPLANATIONS

nvoDIStat

{SNVT_switch}

{0.0 0}, {100.0 1}, {Invalid}

{0.0 0}

Outputs X0, X2, X4, X6, X8, XA, XC, XE status

nvoDIArm

{SNVT_switch}

{0.0 0}, {100.0 1}, {Invalid}

{0.0 0}

Outputs X1, X3, X5, X7, X9, XB, XD, XF status

RS-Flip Flop Mode

NETWORK

VARIABLE

TYPE

{ Range }

{ Default }

EXPLANATIONS

nvoDIStat

{SNVT_switch}

{0.0 0}, {100.0 1}, {Invalid}

{0.0 0}

X0, X2, X4, X6, X8, XA, XC, XE : Set signal

X1, X3, X5, X7, X9, XB, XD, XF : Reset signal

When X0 or X1 receives an one-shot signal, fbDI data is set or reset respec-

tively

nvoDIStat outputs ON signal at Set.

nvoDIArm outputs ON signal at Reset.

nvoDIArm

{SNVT_switch}

{0.0 0}, {100.0 1}, {Invalid}

{0.0 0}

Combination Mode

NETWORK

VARIABLE

TYPE

{ Range }

{ Default }

EXPLANATIONS

nvoDIStat

{SNVT_switch}

{0.0 0}, {100.0 1}, {Invalid}

{0.0 0}

Contact input, nvoDIStat and nvoDIArm Reference Table

nvoDIStat nvoDIArm

OFF OFF 0.0 0 (OFF) Invalid

ON OFF 100.0 1 (ON) Invalid

OFF ON 0.0 0 (OFF) 0.0 0 (OFF)

ON ON 100.0 1 (ON) 100.0 1 (ON)

nvoDIArm

{SNVT_switch}

{0.0 0}, {100.0 1}, {Invalid}

{0.0 0}

Conguration Properties

CONFIGURATION

PROPERTY

NETWORK

VARIABLE

TYPE

{ Range }

{ Default }

EXPLANATIONS

SCPTdirection ----

{SNVT_state}

{0 or 1}

{0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0}

Bit 0, Bit 1: fbDI operating mode

0,0 : Normal mode

1,0 : RS-Flip Flop mode

0,1 : Combination mode

Bit 2 through 15 : Invalid

SCPTinvrtOut nvoDIStat

{SNVT_lev_disc}

{ST_OFF, ST_ON}

{ST_OFF}

Contact input logic is inverted at nvoDIStat.

ST_OFF : OFF at open contact, ON at closed contact

ST_ON : ON at open contact, OFF at closed contact

SCPTinvrtOut nvoDIArm

{SNVT_lev_disc}

{ST_OFF, ST_ON}

{ST_OFF}

Contact input logic is inverted at nvoDIArm.

ST_OFF : OFF at open contact, ON at closed contact

ST_ON : ON at open contact, OFF at closed contact

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere M-system Steuereinheit Handbücher

M-system

M-system R30BS Bedienungsanleitung

M-system

M-system R3-NC2 Bedienungsanleitung

M-system

M-system R6-NP1 Bedienungsanleitung

M-system

M-system R7L-YV2 Bedienungsanleitung

M-system

M-system R7F4HML3-D-DAC32A Bedienungsanleitung

M-system

M-system R8-DCM16ALK Bedienungsanleitung

M-system

M-system R3-NF3 Bedienungsanleitung

M-system

M-system R5T-DA4 Bedienungsanleitung

M-system

M-system M6SXF2 Bedienungsanleitung

M-system

M-system R7HL-DC16A Bedienungsanleitung

M-system

M-system R7C-EC16A Bedienungsanleitung

M-system

M-system R7G4HEIP-6-DC16B Bedienungsanleitung

M-system

M-system 73VR3100 Bedienungsanleitung

M-system

M-system R3-PA4B Bedienungsanleitung

M-system

M-system R3S-DC8 Bedienungsanleitung

M-system

M-system R7ML-DC16D Bedienungsanleitung

M-system

M-system R3-DS4 Bedienungsanleitung

M-system

M-system R7L-RS4 Bedienungsanleitung

M-system

M-system R7L-EC8B Bedienungsanleitung

M-system

M-system R7D-EA16 Bedienungsanleitung

M-system

M-system R7M-RS4 Bedienungsanleitung

M-system

M-system R7E-DA16 Bedienungsanleitung

M-system

M-system R7M-TS4 Bedienungsanleitung

M-system

M-system R3S-RS4A Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung