M-system R7E-PA8 Bedienungsanleitung
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7812-AV Rev.1 P. 1 / 5
INSTRUCTION MANUAL
DC VOLTAGE OUTPUT MODULE, 4 points
(High-speed Link System, isolated, 12 bits data) MODEL
R7HL-YV4L
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
DC voltage output module..................................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVE
• Use dual-shield cables (Shinko Seisen Industry Model
ZHY262 PBA) for the network. If it is not sufficient, use
a ferrite core (Kitagawa Industries Model GRFC-13) for
the network cable.
• The equipment must be mounted inside the instrument
panel of a metal enclosure.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform-
ity.
■POWER INPUT RATING & OPERATIONAL RANGE
• Locate the power input rating marked on the product and
confirm its operational range as indicated below:
24V DC rating: 24V ±10%, approx. 75mA
■GENERAL PRECAUTIONS
• Before you remove the unit or mount it, turn off the power
supply and output signal for safety.
• DO NOT set the switches on the module while the power
is supplied. The switches are used only for maintenance
without the power.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
R7HL-YV4L
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7812-AV Rev.1 P. 2 / 5
COMPONENT IDENTIFICATION
X10 X1
STATION ADD.
CNFG.
12345678
78910
3452
6
1
4567
123
TERM
ON OFF
RUNPWR
ON
■FRONT VIEW■SIDE VIEW
Terminating Resistor SW
Status Indicator LED
Station Address Setting Rotary SW
Output Terminals
Network, Power Supply
Terminals
PC Configurator Jack
Operating Mode Setting DIP SW (SW1)
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
■STATUS INDICATOR LED
ID COLOR FUNCTION
PWR Green Turns on when the internal 5V is sup-
plied normally.
RUN Green Turns on when the refresh data is re-
ceived normally.
■STATION ADDRESS
The left switch determines the sixteenths place digit, while
the right switch does the ones place digit of the address.
The data allocation is 1. (Range: 01H to 3FH)
Station Address Setting (x1)
Station Address Setting (x16)
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
■OPERATING MODE
(*) Factory setting
• Output range (SW1-3, 1-4, 1-5, 1-6)
SW1-3 SW1-4 SW1-5 SW1-6 OUTPUT RANGE
OFF OFF OFF OFF -10 – +10V DC (*)
ON OFF OFF OFF -5 – +5V DC
ON ON OFF OFF 0 – 10V DC
OFF OFF ON OFF 0 – 5V DC
ON OFF ON OFF 1 – 5V DC
ON ON ON ON
PC Configurator setting
• Output at the loss of communication (SW1-7)
SW1-7 OUTPUT AT THE LOSS OF COMMUNICATION
OFF Hold the output (*)
(maintains the last data received normally)
ON Reset the output (to 0%)
• Transfer rate (SW1-8)
SW1-8 TRANSFER RATE
Option code: None Option code: /3
OFF 12 Mbps (*) 3 Mbps
ON 6 Mbps Unused
Note: Be sure to set unused SW1-1 and 1-2 to OFF.
■TERMINATING RESISTOR
To use the terminating resistor, turn the switch ON, and
OFF to invalidate. (Factory setting OFF)
R7HL-YV4L
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7812-AV Rev.1 P. 3 / 5
■NETWORK, POWER SUPPLY TERMINAL ASSIGNMENT
• Full-duplex communication
4
RXD+
567
123
RXD–
+
24V
0V
TXD+ TXD–
FG
NO. ID FUNCTION, NOTES
1 TXD+ Network (slave, transmission +)
2 TXD– Network (slave, transmission –)
3 FG FG
4 RXD+ Network (master, transmission +)
5 RXD– Network (master, transmission –)
6 +24V Power input (24V DC)
7 0V Power input (0V)
• Half-duplex communication
4
TR
+
567
123
TR
–+
24V 0V
NC NC
FG
NO. ID FUNCTION, NOTES
1 NC No connection
2 NC No connection
3 FG FG
4 TR+ Network
5 TR– Network
6 +24V Power input (24V DC)
7 0V Power input (0V)
■OUTPUT TERMINAL ASSIGNMENT
10
5
6
12
789
34
V3
COM3
NC
NC
COM0
V0 V1 V2
COM1 COM2
NO. ID FUNCTION NO. ID FUNCTION
1 NC No connection 6 NC No connection
2 COM0 Common 0 7 V0 Voltage output 0
3 COM1 Common 1 8 V1 Voltage output 1
4 COM2 Common 2 9 V2 Voltage output 2
5 COM3 Common 3 10 V3 Voltage output 3
PC CONFIGURATOR
The following parameters can be set with using PC Configurator Software (model: R7CON).
Refer to the users manual for the R7CON for detailed operation of the software program.
■SETTINGS FOR INDIVIDUAL CHANNELS
PARAMETER AVAILABLE RANGE FACTORY SETTING
Output range
-10 − +10V DC
-5 − +5V DC
0 − 10V DC
0 − 5V DC
1 − 5V DC
-10 − +10V DC
Bias adjustment -320.00 − +320.00 (%) 0.00 (%)
Gain adjustment -3.2000 − +3.2000 1.0000
R7HL-YV4L
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7812-AV Rev.1 P. 4 / 5
TERMINAL CONNECTIONS
Connect the unit as in the diagram.
■EXTERNAL DIMENSIONS unit: mm (inch)
23415
10
789
6
4567
123
DIN RAIL
35mm wide
[5 (.20)]
30 (1.18)
54 (2.13)
17 (.66)
7–M3 SCREW
TERMINALS
for Network, POWER
10–M3 SCREW
TERMINALS
for OUTPUT
115 (4.53)
3 (.12)5.5 (.22) 50 (1.97) 18.5 (.73)
6 (.24) 6 (.24)
■CONNECTION DIAGRAM
Note: In order to improve EMC performance, bond the FG
terminal to ground.
Caution: FG terminal is NOT a protective conductor terminal.
3
7
2
8
5
9
4
10
V0
COM0
V1
COM1
V2
COM2
V3
COM3
4
5
2
1
3
FG
6
7
24V DC
0V
(NC) TXD–
(NC) TXD+
(TR–) RXD–
(TR+) RXD+
OUTPUT 0
OUTPUT 1
OUTPUT 2
OUTPUT 3
Note: Terminal numbers in parentheses are for half-duplex
communication model.
WIRING INSTRUCTIONS
■SCREW TERMINAL
Torque: 0.5 N·m
■SOLDERLESS TERMINAL
Refer to the drawing below for recommended ring tongue
terminal size. Spade tongue type is also applicable.
Recommended solderless terminal:
• Communication cables
Applicable wire size: 0.2 to 0.5 mm2(AWG 26 to 22)
Recommended manufacturer: Japan Solderless Terminal
MFG. Co., Ltd.
• Others
Applicable wire size: 0.25 to 1.65 mm2(AWG 22 to 16)
Recommended manufacturer: Japan Solderless Terminal
MFG. Co., Ltd. or Nichifu Co., Ltd.
4 (.16) min
3.2 (.13) dia.
mm (inch)
6 (.24) max
3.3 (.13) max
R7HL-YV4L
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7812-AV Rev.1 P. 5 / 5
COMMUNICATION CABLE CONNECTIONS
Master Module
RXD+
RXD–
TXD+
TXD–
FG
(SHIELD)
Slave Module
RXD+
RXD–
TXD+
TXD–
FG
(SHIELD)
Slave Module
TXD+
Terminating
Resistor
TXD–
RXD+
RXD–
SHIELD
Terminating
Resistor
Master Module
TR+
TR–
FG
(SHIELD)
Slave Module
TR+
TR–
FG
(SHIELD)
Slave Module
TR+
TR–
SHIELD
Note: Be sure to turn ON the switch of the terminating resistor located at both ends of the modules.
Terminating
Resistor
Terminating
Resistor
■
MASTER CONNECTION
• Full-duplex communication
• Half-duplex communication
I/O DATA DESCRIPTIONS
■ANALOG OUTPUT
0
15
ADD.n
0
15
CH0 – 3
Analog output data
CH designation of
analog output data
Unused
Analog output data
CH designation of
analog output data
Unused
• Di
■ ANALOG OUTPUT (R7HL-YV4L)
• Do
The data is 12-bit binary.
Divided by 4 times scan, 4 points output data is transferred by using CH designation bit.
For Di, the data written to Do is echoed back.
■DATA ACQUISITION PROCEDURE
1) Write the desired CH designation bit (see table below) to the CH designation bit (bit 12 to 14) for the analog output data of
Do, from the host program.
2) After one scan, the channel specified above is updated.
CHANNEL CH DESIGNATION BIT
0 000
1 001
2 010
3 011
Inhaltsverzeichnis
Andere M-system E/A-System Handbücher
M-system
M-system R7F4HEIP-DAC16C Bedienungsanleitung
M-system
M-system R7 Series Bedienungsanleitung
M-system
M-system R3-DC64A Bedienungsanleitung
M-system
M-system R7D-DC16B Bedienungsanleitung
M-system
M-system Devicenet R7F4DD-DA16A-C Bedienungsanleitung
M-system
M-system JC-IO Bedienungsanleitung
M-system
M-system R7L-RS4-R Bedienungsanleitung
M-system
M-system R3-SV4A Bedienungsanleitung
M-system
M-system R3-WT1 Bedienungsanleitung
M-system
M-system R7F4HEIP-DC16A Bedienungsanleitung
M-system
M-system R7F4DC-DC16A-H Bedienungsanleitung
M-system
M-system R7E-EC8A Bedienungsanleitung
M-system
M-system R7F4DC-DA16A-H Bedienungsanleitung
M-system
M-system R7HL-PA4E Bedienungsanleitung
M-system
M-system R7C-DA16 Bedienungsanleitung
M-system
M-system R7E-YV2 Bedienungsanleitung
M-system
M-system R7D-SV4/UL Bedienungsanleitung
M-system
M-system R7L-DC16B-R Bedienungsanleitung
M-system
M-system JC-ECT Bedienungsanleitung
M-system
M-system R3-SS8N Bedienungsanleitung
Beliebte E/A-System Handbücher anderer Marken
WAGO
WAGO 750-344 Bedienungsanleitung
Teknim
Teknim TWM-1887 Bedienungsanleitung
Intelligent Appliance
Intelligent Appliance IA-2662-E Bedienungsanleitung
BERGHOF
BERGHOF ECC DIO 16/16 Bedienungsanleitung
Advantech
Advantech PCM-27J3AU Installations- und Betriebshandbuch
Festo
Festo CP-E08-M12-CL Bedienungsanleitung
