M-system R80UST4 Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7028 P. 1 / 9

INSTRUCTION MANUAL

UNIVERSAL INPUT MODULE

(4 points, isolated, tension clamp terminal block) MODEL R80UST4

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Universal input module ......................................................(1)

CJC sensor...........................................................................(4)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside a panel.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■GENERAL PRECAUTIONS

• Before you remove or mount the unit, turn off the power

supply and output signal for safety.

• DO NOT set the switches while the power is supplied.

The switches are used only for maintenance without the

power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■POWER UP

• Turn the power on at the same time as the power/network

module or turn the R80PS1 on before the power/network

module turned on. If the R80PS1 is not turned on within

3 seconds after the power/network module is turned on,

I/O modules are not correctly recognized.

R80UST4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7028 P. 2 / 9

INSTALLATION

■HOW TO MOUNT THE MODULE ON DIN RAIL

Confirm that the locking clamps of the extension power supply module

are set. Insert the module in parallel to the next one while aligning the

grooves of both modules (A & B in the above figure).

Maintain it perpendicularly to the rail.

More I/O modules can be added in the same manner.

• Protective Cover

The protective cover is to be attached over the connected I/O module

at the right end.

Align the hooks on the cover with the grooves of the module and slide it

straight until the hooks are latched.

When removing the cover, pull it out while squeezing the hooks inward.

Groove

Hook

R80UST4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7028 P. 3 / 9

■HOW TO UNMOUNT THE MODULE FROM DIN RAIL

Release the locking clamps and pull out straight the module.

Caution !

1)Be careful not to hurt your hand by pointed edges of the internal bus

connector.

2) I/O modules cannot hold tightly on the DIN rail by themselves without

power/network module.

Secure them to the position if necessary by using DIN rail end plates.

• Removing an intermediate module

R80UST4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7028 P. 4 / 9

COMPONENT IDENTIFICATION

Status Indicator LED

Input Status Indicator LED

Internal Bus Connector

Input Connector

Terminator DIP SW

SW2

SW1

Module Address

DIP SW

■STATUS INDICATOR LED / INPUT STATUS INDICATOR LED

LED OPERATION COLOR FUNCTION

RUN ON Red Upper communication: Stopping or abnormal

Internal communication: Abnormal

ON Green Upper communication: Normal

Internal communication: Normal

Blink

1 sec. sycle

– Burnout is detected or with input value error

(≤ -15%, ≥ +115%, becomes less than the lower limit or exceeds the

upper limit of usable range).

Blink

400 msec. cycle

– Input circuit abnormality (AD converter response failure)

OFF – Upper communication: Stopping or abnormal

Internal communication: Normal

Input Status Indi-

cator LED

OFF Red Input data in the range

ON Burnout is detected or with input value error

(≤ -15%, ≥ +115%, becomes less than the lower limit or exceeds the

upper limit of usable range).

Input circuit abnormality (AD converter response failure)

R80UST4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7028 P. 5 / 9

■OPERATING MODE SETTING

(*) factory default setting

Note. Be sure to OFF the unused SW2-2.

• Module Address Setting

Conﬁgurate the mosule address with DIP Switch.

0 - 15 are available for module address.

MODULE

ADDRESS

SW1

1234

0(*) OFF OFF OFF OFF

1 ON OFF OFF OFF

2 OFF ON OFF OFF

3 ON ON OFF OFF

4 OFF OFF ON OFF

5 ON OFF ON OFF

6 OFF ON ON OFF

7 ON ON ON OFF

8 OFF OFF OFF ON

9 ON OFF OFF ON

10 OFF ON OFF ON

11 ON ON OFF ON

12 OFF OFF ON ON

13 ON OFF ON ON

14 OFF ON ON ON

15 ON ON ON ON

• Terminator Setting

Terminator SW2-1

Disabled (*) OFF

Enabled ON

■INPUT CONNECTOR TERMINAL ASSIGNMENT

PIN NO. ID FUNCTION

1 U1 U1

2 NC Unused

3 NC Unused

4 U6 U6

5 U2 U2

6 U3 U3

7 U4 U4

8 U5 U5

• Universal input terminal assignment

FUNCTION

Wide span voltage

(-10 - +10V DC)

DC Current Narrow span voltage

(-1000 - +1000mV DC)

Thermocouple

RTD/

Resistor (3-wire)

RTD/

Resistor (2-wire)

Potentiometer

Wide span voltage

– – – – – –

U2 –

DC Current

– – – – –

U3 – – Narrow span voltage

Thermocouple+

RTD-b – Input S

U4 – – – CJM RTD-B RTD-B Input L

U5 Common Common Common

Thermocouple-

RTD-A RTD-A Input H

U6 – – – CJM – – –

R80UST4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7028 P. 6 / 9

PC CONFIGURATOR

The following parameters can be set with using PC Conﬁgurator Software (model: R80CFG)

Refer to the users manual for the R80CFG for detailed operation of the software program.

■CHANNEL INDIVIDUAL SETTING

ITEM SETTING RANGE DEFAULT VALUE

Unused setting CH enabled

CH disabled

CH enabled

Input type DC voltage -10 - +10 V DC

-1000 - +1000 mV DC

-10 - +10 V DC

DC current -20 - +20 mA DC

Potentiometer POT 0 - 4000 Ω

POT 0 - 2500 Ω

POT 0 - 1200 Ω

POT 0 - 600 Ω

POT 0 - 300 Ω

POT 0 - 150 Ω

Resistpr OHM 0 - 4000 Ω

RTD RTD Pt 100

RTD Pt 500

RTD Pt 1000

RTD Pt 50 Ω

RTD JPt 100

RTD Ni 508.4 Ω

RTD Cu 10

Thermocouple TC (PR)

TC K

TC E

TC J

TC T

TC B

TC R

TC S

TC C

TC N

TC U

TC L

TC P

Wiring 2-wire

3-wire

Burnout Upscale

Downscale

None

CJC Enabled

Disabled

Temp. unit degC

degF

Zero ﬁne adj. -320.00 - +320.00 (%) 0.00 (%)

Gain ﬁne adj. -3.2000 - +3.2000 1.0000

Zero base depends on input types*10.000

Full base depends on input types*10.000

Zero scaling -32,000 - +32,000 0

Full scaling -32,000 - +32,000 10,000

First order lag ﬁlter 0.0, 0.5 - 60.0 (sec.) 0.0 (sec.)

*1. For details, refer to the users manual of R80CFG

■CHANNEL BATCH SETTING

ITEM SETTING RANGE DEFAULT VALUE

Version no. – –

Simulate input Normal input

Simulated data

Normal input

R80UST4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7028 P. 7 / 9

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

For thermocouple input, attach the CJC sensor together with input wining to the input screw terminals.

■EXTERNAL DIMENSIONS unit : mm (inch)

24 [.94] (3 [.12])

55 [2.17]

67 [2.64] (4 [.16])

115 [4.53] 6 [.24]6 [.24]

7 [.28] 7 [.28]

DIN rail

(35mm wide)

R80UST4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7028 P. 8 / 9

■CONNECTION DIAGRAM

CONNECTOR

INTERNAL BUS

INTERNAL POWER

Universal input 1

Universal input 2

Universal input 3

Universal input 4

R80UST4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7028 P. 9 / 9

INPUT

−

INPUT

−

• DC Voltage (-10‑+10V DC) • DC Current (0 ‑20mA DC)

■UNIVERSAL INPUT CONNECTION

• RTD or Resistor (3-wire)

• DC Voltage (-1000 ‑+1000mV DC)

• Thermocouple • Potentiometer• RTD or Resistor (2-wire)

INPUT

−

‒–

max.

min.

−

WIRING INSTRUCTIONS

■TENTION CLAMP TERMINAL BLOCK

Unit side connector: DMC0,5/4-G1-2,54 P20THR R44

(Phoenix Contact)

Cable side connector: DFMC0,5/4-ST-2,54

(Phoenix Contact)

Applicable wire size: 0.14 − 0.5 mm2

Stripped length: 7 mm

Recommended solderless terminal

• AI0,14-6GY0.14mm2(Phoenix Contact)

• AI0,25-6YE0.25mm2(Phoenix Contact)

• A0,34-70.34mm2(Phoenix Contact)

Inhaltsverzeichnis

Andere M-system E/A-System Handbücher

M-system

M-system R3-SV16N Bedienungsanleitung

M-system

M-system R7L-DAC16 Bedienungsanleitung

M-system

M-system R3-WT1 Bedienungsanleitung

M-system

M-system R1M-P4 Bedienungsanleitung

M-system

M-system R7M-CT4E-R Bedienungsanleitung

M-system

M-system R8-CT4E Bedienungsanleitung

M-system

M-system R3-TS4 Bedienungsanleitung

M-system

M-system Devicenet R7F4HD-DC32A Bedienungsanleitung

M-system

M-system Devicenet R7F4DD-DAC16C-C Bedienungsanleitung

M-system

M-system R7C-SV4 Bedienungsanleitung

M-system

M-system EtherCAT R7I4DECT-1-YVF4 Bedienungsanleitung

M-system

M-system R7C-CT4E Bedienungsanleitung

M-system

M-system R80YVT4N Bedienungsanleitung

M-system

M-system R7D-DC16A Bedienungsanleitung

M-system

M-system R7L-EA8 Bedienungsanleitung

M-system

M-system M5XPHS Bedienungsanleitung

M-system

M-system M8BS2-042 Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R30PA2 Bedienungsanleitung

M-system

M-system R7L-DC16A Bedienungsanleitung

M-system

M-system R5 Series Bedienungsanleitung

M-system

M-system Mini-MW Series Bedienungsanleitung

M-system

M-system R6S-DA4 Bedienungsanleitung

M-system

M-system R7M-TS4-R Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung