M-system R80DCT16A2 Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7032 P. 1 / 5

INSTRUCTION MANUAL

NPN TRANSISTOR OUTPUT MODULE, 16 points

(Tension clamp terminal block) MODEL

R80DCT16A2

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

NPN transistor output module...........................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside a panel.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■GENERAL PRECAUTIONS

• Before you remove or mount the unit, turn off the power

supply and input signal for safety.

• Switches on the side of the module can be set for mainte-

nance only while the power supply is off. Do not access

them while the power is supplied.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■EXCITATION SUPPLY

• Output connector: Rated current 3 A DC (rated current 3

A for internal fuse (slow blow fuse i2t (A2sec) max. 5.04).

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

■HOW TO MOUNT THE MODULE ON DIN RAIL

• I/O Module

Confirm that the locking clamps of the I/O module are set.

Insert the module in parallel to the next one while aligning the grooves of

both modules (A & B in the above figure).

Maintain it perpendicularly to the rail.

More I/O modules can be added in the same manner.

R80DCT16A2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7032 P. 2 / 5

• Protective Cover

Hook

Groove

When removing the cover, pull it out while squeezing the hooks inward.

The protective cover is to be attached over the connected I/O module

at the right end.

Align the hooks on the cover with the grooves of the module and slide it

straight until the hooks are latched.

■HOW TO UNMOUNT THE MODULE FROM DIN RAIL

• Release the locking clamps and pull out straight the module.

• Removing an intermediate module

Note 1: Be careful not to hurt your hand by pointed edges of the internal

bus connector.

Note 2: I/O modules cannot hold tightly on the DIN rail by themselves

without power/network module.

Secure them to the position if necessary by using DIN rail end

plates.

R80DCT16A2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7032 P. 3 / 5

COMPONENT IDENTIFICATION

Module Address

Setting DIP SW

■FRONT VIEW ■SIDE VIEW

Discrete Output

Satus Indicator LEDs

Status Insicator LED

Internal Bus Connector

Output Connector

RUN

SW1

Terminator

DIP SW

SW2

■INDICATOR LED

LED

OPERATION

FUNCTION

Status OFF

Upper communication: Stopping

or abnormal

Internal communication: Normal

Red ON

Upper communication: Stopping or

abnormal

Internal communication: Abnormal

Green ON

Upper communication: Normal

Internal communication: Normal

Orange ON

Upper communication: Normal

Internal communication: Abnormal

Orange Blinking Circuit abnormality

(blinking in 400 msec. cycle)

Input

Status

OFF Discrete input is OFF.

Green ON Discrete input is ON.

■INPUT CONNECTOR ASSIGNMENT

PIN NO.ID FUNCTION

1 Do1 Output 1

2 Do2 Output 2

3 Do3 Output 3

4 Do4 Output 4

5 Do5 Output 5

6 Do6 Output 6

7 Do7 Output 7

8 Do8 Output 8

9 Do9 Output 9

10 Do10 Output 10

11 Do11 Output 11

12 Do12 Output 12

13 Do13 Output 13

14 Do14 Output 14

15 Do15 Output 15

16 Do16 Output 16

17 0V Exc. supply 0V

18 24V Exc. supply 24V

■OPERATING MODE SETTING

(*) Factory setting

Note) Be sure to set unused SW 1-5 through 1-8 to OFF.

• MODULE ADDRESS

Selectable between 0 and 15, with DIP switch 1-1 to 4.

Set the module addresses consecutively starting at 0 such that

there is no duplicate or vacant address.

MODULE ADDRESS SW1

1234

0 OFF OFF OFF OFF

1 ON OFF OFF OFF

2 OFF ON OFF OFF

3 ON ON OFF OFF

4 OFF OFF ON OFF

5 ON OFF ON OFF

6 OFF ON ON OFF

7 ON ON ON OFF

8 OFF OFF OFF ON

9 ON OFF OFF ON

10 OFF ON OFF ON

11 ON ON OFF ON

12 OFF OFF ON ON

13 ON OFF ON ON

14 OFF ON ON ON

15 ON ON ON ON

■TERMINATOR DIP SW

TERMINATOR SW2

Without (*) OFF

With ON

R80DCT16A2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7032 P. 4 / 5

PC CONFIGURATOR

The following parameters can be set using PC Conﬁgurator Software (model: R80CFG)

Refer to the users manual for the R80CFG for detailed operation of the software program.

ITEM SETTING RANGE DEAULT VALUE

Output at time of communication disconnection Output hold

Output clear

Output hold

Note) Settings are programmed by the PC Conﬁgurator via the Power/Network Module.

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm [inch]

115 [4.53]6 [.24]7 [.28] 6 [.24] 7 [.28]

DIN rail

(35 mm wide)

(3 [.12]) (4 [.16])

24 [.94] 72 [2.83]

55 [2.17]

R80DCT16A2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-7032 P. 5 / 5

■CONNECTION DIAGRAM

INTERNAL POWER

INTERNAL BUS

EXC. SUPPLY

Do 1

Do 2

Do 3

Do 4

Do 5

Do 6

Do 7

Do 8

Do 16

Do 15

Output Connector

■OUTPUT CIRCUIT

Control

Circuit

1Do 1

Do 16

+24V

Do 9

Do 10

Do 14

Do 12

Do 13

Do 11

CONNECTOR

WIRING INSTRUCTIONS

■• INPUT CONNECTOR

Unit side connector: MC1,5/18-GF-3,5 (Phoenix Contact)

Cable side connector: FMC1,5/18-STF-3,5 (Phoenix Contact)

(included in the package)

Applicable wire size: 0.2 − 1.5 mm2

Stripped length: 10 mm

Recommended solderless terminal

• AI0,25−10YE 0.25 mm2(Phoenix Contact)

• AI0,34−10TQ 0.34 mm2(Phoenix Contact)

• AI0,5−10WH 0.5 mm2(Phoenix Contact)

• AI0,75−10GY 0.75 mm² (Phoenix Contact)

• A1−10 1.0 mm² (Phoenix Contact)

• A1,5−10 1.5 mm² (Phoenix Contact)

Inhaltsverzeichnis

Andere M-system E/A-System Handbücher

M-system

M-system R7F4HEIP-DAC16C Bedienungsanleitung

M-system

M-system R3-WT1 Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system R7ML-EA8 Bedienungsanleitung

M-system

M-system R7M-DA16F Bedienungsanleitung

M-system

M-system R7F4HC-DC32B-K Bedienungsanleitung

M-system

M-system R3-PD16C Bedienungsanleitung

M-system

M-system M5SN-AA Bedienungsanleitung

M-system

M-system R8-SS4NJ Bedienungsanleitung

M-system

M-system R7C-EC16B Bedienungsanleitung

M-system

M-system R5T-RS Bedienungsanleitung

M-system

M-system R7D-DC16A Bedienungsanleitung

M-system

M-system R3S-YV4 Bedienungsanleitung

M-system

M-system Devicenet R7F4DD-DA16A-H Bedienungsanleitung

M-system

M-system R7L-EA16 Bedienungsanleitung

M-system

M-system R7E-EC8A Bedienungsanleitung

M-system

M-system R7E-EC8B Bedienungsanleitung

M-system

M-system R3-SV16N Bedienungsanleitung

M-system

M-system R8-YVT4N Bedienungsanleitung

M-system

M-system R30NCIE1 Bedienungsanleitung

M-system

M-system R7F4HEIP-DC16A Bedienungsanleitung

M-system

M-system R7ML-YS2-R Bedienungsanleitung

M-system

M-system R7ML-EA8 Bedienungsanleitung

M-system

M-system R7G4FML3-6-DA16 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung