M-system 18PA Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-1869 Rev.1 P. 1 / 3

INSTRUCTION MANUAL

PHASE ANGLE TRANSDUCER MODEL 18PA

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, approx. 80mA

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +55°C

(23 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Body

Specifications

Front Cover

(Connection diagram

behind)

■FRONT VIEW (with cover open)

Span Adj.

Zero Adj.

INSTALLATION

Use Standard Rack (model: 18BXx or 18KBXx).

1 8 PA

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-1869 Rev.1 P. 2 / 3

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram behind the front cover.

■EXTERNAL DIMENSIONS unit: mm (inch)

110 (4.33 )

93 (3.66)

24 (.94)

7 (.28)

78 (3.07)32 (1.26)

8–M3.5

SCREW

7 (.28)

2–M3

SCREW

■CONNECTION DIAGRAM

■3-PHASE/3-WIRE

CONNECTOR

LOAD

123

SOURCE

P3U

P2V

FUSE VT

OUTPUT 1

OUTPUT 2

POWER

■TERMINAL ASSIGNMENTS

1 8 PA

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-1869 Rev.1 P. 3 / 3

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input voltage: Check voltage supplied to the rack

(model: 18BXx or 18KBXx). For the DC power source, be

sure that the ripple level is within 10% p-p.

3) Voltage input: Check that the input shows within 85 –

120% of the rated voltage.

4) Current input: Check that the input shows within 10 –

120% of the rated current.

5) Output: Check that the load resistance meets the de-

scribed speciﬁcations.

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

speciﬁcations, therefore you usually do not need any cali-

bration.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

■HOW TO CALIBRATE THE OUTPUT 1

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0%.

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above proce-

dure 1) – 3).

5) No need of adjustments for the Output 2.

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the “ADJUST-

MENT PROCEDURE” explained earlier.

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

Andere M-system Wandler Handbücher

M-system

M-system M5XWTU Bedienungsanleitung

M-system

M-system W2PV Bedienungsanleitung

M-system

M-system TPV Bedienungsanleitung

M-system

M-system KUWEN Bedienungsanleitung

M-system

M-system 18RP Bedienungsanleitung

M-system

M-system LT-UNIT Series Bedienungsanleitung

M-system

M-system LTHZ Bedienungsanleitung

M-system

M-system 18PF Bedienungsanleitung

M-system

M-system L2PA Bedienungsanleitung

M-system

M-system 18PV Bedienungsanleitung

M-system

M-system BPV Bedienungsanleitung

M-system

M-system L3PK Bedienungsanleitung

M-system

M-system LWT Bedienungsanleitung

M-system

M-system L3CK Bedienungsanleitung

M-system

M-system Mini-M M2PV Bedienungsanleitung

M-system

M-system LT-UNIT Series Bedienungsanleitung

M-system

M-system LTCE Bedienungsanleitung

M-system

M-system LTCNE Bedienungsanleitung

M-system

M-system L2CA Bedienungsanleitung

M-system

M-system 18HZ Bedienungsanleitung

M-system

M-system LECA Bedienungsanleitung

M-system

M-system LTWTN Bedienungsanleitung

M-system

M-system LTCE Bedienungsanleitung

M-system

M-system PV Bedienungsanleitung

Beliebte Wandler Handbücher anderer Marken

HBM

HBM AD101B Bedienungsanleitung

Camille Bauer

Camille Bauer SINEAX F534 Bedienungsanleitung

Trane

Trane KIT 16724 Montageanleitung

Lumel

Lumel P18 Bedienungsanleitung

B&C Speakers

B&C Speakers DE75PTN Bedienungsanleitung

MAMAC SYSTEMS

MAMAC SYSTEMS PR-243 Handbuch

Mianyang Weibo Electronic

Mianyang Weibo Electronic WB Series Bedienungsanleitung

ProMinent

ProMinent Dulcometer DMT Bedienungsanleitung

MKS

MKS MicroPirani 925 Series Anleitung zur Verwendung

WIKA

WIKA WU-20 Bedienungsanleitung

Alcatel Vacuum Technology

Alcatel Vacuum Technology BARATRON 622A Bedienungsanleitung

Camille Bauer

Camille Bauer SIRAX CH-5610 Bedienungsanleitung

WIKA

WIKA F2802 Bedienungsanleitung

Veris Industries

Veris Industries PW Series Bedienungsanleitung

HBM

HBM TJ1-S6 Bedienungsanleitung

Simrad

Simrad ES120-7C - REV D Benutzerhandbuch

HBM

HBM C18 Bedienungsanleitung

Airmar

Airmar M260 Bedienungsanleitung