M-system PV Bedienungsanleitung

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-2411 Rev.5 P. 1 / 2

INSTRUCTION MANUAL

P/I TRANSDUCER MODEL PV

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner (body + base socket).............................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

AC power: Rating ±10%, 50/60 ±2 Hz, approx. 2VA

DC power: Rating ±10%, approx. 2W

■GENERAL PRECAUTIONS

• Before you remove the unit from its base socket or mount

it, turn off the power supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +60°C

(23 to 140°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Specifications

M•UNIT

MODEL

Body

Base Socket

(top)

Zero Adj.

Span Adj.

INSTALLATION

Refer to “EXTERNAL DIMENSIONS.”

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-2411 Rev.5 P. 2 / 2

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

• When mounting, no extra space is needed between units.

• Fitting is provided for 1/4”NPT connection.

12345

101 (3.98)

37.5 (1.48)

approx.

27(1.06)

15 (.59)

54 (2.13)

12 (.47)

17.5 (.68)138 (5.43)

14.5 (.57)

44 (1.73)

54 (2.13)

101 (3.98)

5–M3.5x7 (.14x.28)

SCREW

2–5 (.20) dia.

MTG HOLE

15 (.59) deep

FITTING

PNEUMATIC

CONNECTION

Rc1/4” or 1/4”NPT

■CONNECTION DIAGRAM

–

U(+)

V(–)

OUTPUT

POWER

INPUT

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

PIPING

The pneumatic inlet is female screwed of Rc 1/4” (1/4” NPT

optional with a ﬁtting). Tightening torque is at the maxi-

mum of 12 N·m. Check that there is no air leak at the con-

nection after sealing it.

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input voltage: Check voltage across the terminal

1 – 2 with a multimeter.

3) Input: Check that there is no air leak at the pneumatic

connection.

4) Output: Check that the load resistance meets the de-

scribed speciﬁcations.

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

speciﬁcations, therefore you usually do not need any cali-

bration.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

■HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0%.

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above proce-

dure 1) – 3).

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the “ADJUST-

MENT PROCEDURE” explained earlier.

Andere M-system Wandler Handbücher

M-system

M-system Mini-M M2PV Bedienungsanleitung

M-system

M-system 18HZ Bedienungsanleitung

M-system

M-system LTHZ Bedienungsanleitung

M-system

M-system LWT Bedienungsanleitung

M-system

M-system LTCE Bedienungsanleitung

M-system

M-system L2CA Bedienungsanleitung

M-system

M-system L2PA Bedienungsanleitung

M-system

M-system 18RP Bedienungsanleitung

M-system

M-system LTWTN Bedienungsanleitung

M-system

M-system 18PA Bedienungsanleitung

M-system

M-system LTCE Bedienungsanleitung

M-system

M-system L3PK Bedienungsanleitung

M-system

M-system 18PF Bedienungsanleitung

M-system

M-system W2PV Bedienungsanleitung

M-system

M-system HVPN Bedienungsanleitung

M-system

M-system LT-UNIT Series Bedienungsanleitung

M-system

M-system BPV Bedienungsanleitung

M-system

M-system 18PV Bedienungsanleitung

M-system

M-system TPV Bedienungsanleitung

M-system

M-system L3CK Bedienungsanleitung

M-system

M-system LT-UNIT Series Bedienungsanleitung

M-system

M-system LTCNE Bedienungsanleitung

M-system

M-system LECA Bedienungsanleitung

M-system

M-system M5XWTU Bedienungsanleitung

Beliebte Wandler Handbücher anderer Marken

HBM

HBM AD101B Bedienungsanleitung

Camille Bauer

Camille Bauer SINEAX F534 Bedienungsanleitung

Trane

Trane KIT 16724 Montageanleitung

Lumel

Lumel P18 Bedienungsanleitung

B&C Speakers

B&C Speakers DE75PTN Bedienungsanleitung

MAMAC SYSTEMS

MAMAC SYSTEMS PR-243 Handbuch

Mianyang Weibo Electronic

Mianyang Weibo Electronic WB Series Bedienungsanleitung

ProMinent

ProMinent Dulcometer DMT Bedienungsanleitung

MKS

MKS MicroPirani 925 Series Anleitung zur Verwendung

WIKA

WIKA WU-20 Bedienungsanleitung

Alcatel Vacuum Technology

Alcatel Vacuum Technology BARATRON 622A Bedienungsanleitung

Camille Bauer

Camille Bauer SIRAX CH-5610 Bedienungsanleitung

WIKA

WIKA F2802 Bedienungsanleitung

Veris Industries

Veris Industries PW Series Bedienungsanleitung

HBM

HBM TJ1-S6 Bedienungsanleitung

Simrad

Simrad ES120-7C - REV D Benutzerhandbuch

HBM

HBM C18 Bedienungsanleitung

Airmar

Airmar M260 Bedienungsanleitung