M-system 27RS Bedienungsanleitung
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7653-A Rev.3 P. 1 / 3
INSTRUCTION MANUAL
RTD TRANSMITTER
(PC programmable) MODEL 27RS
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
Signal conditioner ...............................................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
When using this product in potentially explosive atmos-
phere or hazardous (classified) location, you have to follow
the safety procedure to install it. Please refer to “SAFE IN-
STALLATION MANUAL” for each type of certification.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
• The actual installation environments such as connected
devices and connected wires may affect the protection
level of this unit when it is integrated in a panel system.
The user may have to review the CE requirements in re-
gard to the whole system and employ additional protec-
tive measures to ensure the CE conformity.
■GENERAL PRECAUTIONS
• Before you remove the module, turn off the power supply
and input signal for safety.
■ENVIRONMENT
• When heavy dust or metal particles are present in the air,
install the module inside proper housing with sufficient
ventilation.
• Do not install the module where it is subjected to con-
tinuous vibration. Do not subject the module to physical
impact.
• Environmental temperature must be within -40 to +85°C
(-40 to +185°F) with relative humidity within 0 to 95%
RH in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
• The module is designed to function as soon as power is
supplied, however, a warm up for 10 minutes is required
for satisfying complete performance described in the data
sheet.
COMPONENT IDENTIFICATION
Specifications
INSTALLATION unit : mm (inch)
This module is suitable for mounting inside a DIN type B
head.
33 (1.30)
2–M4 SCREW
The screws are to be provided by the customer.
27RS
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7653-A Rev.3 P. 2 / 3
TERMINAL CONNECTIONS
Connect the module as in the diagram below.
■EXTERNAL DIMENSIONS unit : mm (inch)
44 (1.73) dia.
6.3
(.25)
33 (1.30) 6 (.24) dia.
16.5 (.65)
6–M3 SCREW
2–4.5 (.18) dia.
MTG HOLE
20.7 (.81)
19.5 (.77)
12.7 (.5)
14
32
–+
7.6 (.30) dia.
■CONNECTION DIAGRAM
*2. Limited to 250 – 500Ω when using the communication
to configure the module.
4
2
3
1
+
–
LOAD
OUTPUT
24V DC
4 – 20mA DC
*2
INPUT *1
*1. Input Connection Examples
4
2
3
1
■ RTD & RESISTANCE
• Two-wire
4
2
3
1
• Three-wire
B
B
A
B
A
4
2
3
1
• Four-wire
B
B
A
A
WIRING INSTRUCTIONS
■SCREW TERMINAL
Torque: 0.5 N·m
CHECKING
1) Terminal wiring: Check that all cables are correctly con-
nected according to the connection diagram.
2) Input: Check the input signal.
If RTD wires are broken, the output goes over 100% (be-
low 0% with downscale) due to burnout function. Check
leadwires in such a case.
3) Output: Check that the load is within the permissible
limit including wiring resistance.
Load Resistance (Ω) = Supply Voltage (V) – 9 (V)
0.023 (A)
(including leadwire resistance)
ADJUSTMENT PROCEDURE
To calibrate the signal to match with a receiving instru-
ment or to change the factory-set configurations, use the PC
Configurator software installed on a Windows PC via the
Bell202 Modem (model COP-HU).
The PC Configurator software is downloadable at M-Sys-
tem’s web site: http://www.m-system.co.jp
LIGHTNING SURGE PROTECTION
M-System offers a series of lightning surge protector for
protection against induced lightning surges. Please contact
M-System to choose appropriate models.
27RS
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp
EM-7653-A Rev.3 P. 3 / 3
FUNCTION MONITOR LED (option /M)
■FUNCTION MONITOR LED
32
41
–+
Function
Monitor LED
■INPUT MONITOR: The input 0 – 100% is converted into a combination of 1-second (1 unit) and 0.25-second (0.2 unit) cycled
pulses. 1 unit corresponds to 25%, while 0.2 unit corresponds to 5%. 0% equals to 1 unit, while 100% cor-
responds to 5 units. The input % is represented in the total number of 1-unit pulses and 0.2-unit pulses,
repeated in the sequence of ‘1-unit pulses ––> 0.2-unit pulses ––> OFF for 1 second or more.’
[Examples]
25% = 2 units
30% = 2.2 units
45% = 2.8 units
50% = 3 units
100% = 5 units
0% = 1 unit
≥1 second
1 UNIT
25%
ON OFF
1 sec.
0.2 UNIT
5%
0.25 sec.
■ERROR MONITOR: Indicates the transmitter’s error status.
Lower overrange: The input signal is lower than the out-
put’s lower range limit.
2 sec. cycle
0.125 sec. OFF
Upper overrange: The input signal is higher than the out-
put’s upper range limit.
0.125 sec. OFF - ON - OFF
2 sec. cycle
Burnout: Sensor wire breakdown is detected.
0.125 sec. ON - OFF
Internal error: The CPU detects an internal error.
0.125 sec. ON - OFF - ON
1 sec. cycle
Andere M-system Sender Handbücher
M-system
M-system F2RS Bedienungsanleitung
M-system
M-system 10JM Bedienungsanleitung
M-system
M-system M5XPA Bedienungsanleitung
M-system
M-system KVS Bedienungsanleitung
M-system
M-system M3SXT Bedienungsanleitung
M-system
M-system M5 Series Bedienungsanleitung
M-system
M-system Mini-MW Series Bedienungsanleitung
M-system
M-system Mini-M M2PA Bedienungsanleitung
M-system
M-system M3LPA Bedienungsanleitung
M-system
M-system W2RS Bedienungsanleitung
M-system
M-system 10VK Bedienungsanleitung
M-system
M-system W2VS Bedienungsanleitung
M-system
M-system KAC Bedienungsanleitung
M-system
M-system CTS2 Bedienungsanleitung
M-system
M-system M5CT-5AM Bedienungsanleitung
M-system
M-system MXLC Bedienungsanleitung
M-system
M-system M5PA Bedienungsanleitung
M-system
M-system Mini-M M2XRP2 Bedienungsanleitung
M-system
M-system M2EXS Bedienungsanleitung
M-system
M-system W5LCS Bedienungsanleitung
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
