M-system 6M Bedienungsanleitung

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

(Option) DIN rail mounting plate (model: A-31) .........(1 set)

(Option) Spring clip (model: A-02)................................(1 set)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +70°C

(23 to 158°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Specifications

Knurled Knob

Body

Knurled Knob

Connection Diagram

(Top)

INSTALLATION

■35-mm DIN RAIL MOUNTING PLATE A-31 (optional) unit: mm (inch)

1) Attach the unit to the DIN rail mounting plate with

screws included in the package.

2) Set the plate so that its DIN rail adapter is at the bottom.

Hang the upper hook at the rear side on the DIN rail

and push in the lower. When removing the plate, push

down the DIN rail adapter utilizing minus screwdriver

and pull.

80 (3.15) MIN.

■SPRING CLIP A-02 (optional)

1) Remove the two ﬂat-

head screws Alocated at

the bottom as shown to

the right.

2) Set Spring Clip Bon

the mounting hole and

tighten it as shown to

the right with a binding

screw Cincluded in the

package.

3) Check that the clips

contract and release

smoothly.

POTENTIOMETER TRANSMITTER MODEL 6M

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-4215 Rev.5 P. 1 / 2

INSTRUCTION MANUAL

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the top of the unit.

■EXTERNAL DIMENSIONS unit: mm (inch)

76 (2.99) dia. 40 (1.57)

52.5 (2.07)

1 (.04)

60.9 (2.40)

46 (1.81)

50 (1.97)

4–M3 (.12) TAP

6 (.24) deep

1 2 3 4

5 6

■CONNECTION DIAGRAM

POTENTIOMETER

max.

min.

–

LOAD

OUTPUT

24V DC

4 – 20mA DC

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.6 N·m

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Input: Check voltage across the terminal 2 (+) – 3 (–)

with a voltmeter to show 0V at 0% potentiometer input

and the same voltage as that across 1 (+) – 3 (–) at 100%

input.

3) Output: Check that the load is within the permissible

limit including wiring resistance.

Load Resistance (Ω) = Supply Voltage (V) – 13 (V)

0.02 (A)

(including leadwire resistance)

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory with the total resist-

ance input, therefore you do not need any calibration if you

use the potentiometer’s total resistance.

When you do not use the total resistance or in case of regu-

lar calibration, adjust the output as explained in the follow-

ing. Zero and Span adjustments are located behind the top

cover. Release the knurled knobs and open the cover.

1234

VR1 VR2

■HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) ZERO: Apply 0% input and adjust output to 0% with the

VR1.

2) SPAN: Apply 100% input and adjust output to 100% with

the VR2.

3) Check ZERO adjustment again with 0% input.

4) When ZERO value is changed, repeat the above proce-

dure 1) – 3).

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the “ADJUST-

MENT PROCEDURE” explained earlier.

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-4215 Rev.5 P. 2 / 2

Andere M-system Sender Handbücher

M-system

M-system MXT Bedienungsanleitung

M-system

M-system 10JR Bedienungsanleitung

M-system

M-system W2RS Bedienungsanleitung

M-system

M-system Mini-M M2XU Bedienungsanleitung

M-system

M-system 18KJV Bedienungsanleitung

M-system

M-system F2RS Bedienungsanleitung

M-system

M-system W2CA Bedienungsanleitung

M-system

M-system 99SVA Bedienungsanleitung

M-system

M-system 10AC Bedienungsanleitung

M-system

M-system M3SXV Bedienungsanleitung

M-system

M-system 6AC Bedienungsanleitung

M-system

M-system Mini-M M2AMS Bedienungsanleitung

M-system

M-system 10VF2 Bedienungsanleitung

M-system

M-system M6SCTC Bedienungsanleitung

M-system

M-system KC Bedienungsanleitung

M-system

M-system 10MS Bedienungsanleitung

M-system

M-system Mini-M M2VF Bedienungsanleitung

M-system

M-system W2AC Bedienungsanleitung

M-system

M-system Mini-M M2LCS Bedienungsanleitung

M-system

M-system Mini-M M2UDS2 Bedienungsanleitung

M-system

M-system 27TS Bedienungsanleitung

M-system

M-system 10JRE Bedienungsanleitung

M-system

M-system B3VS/2 Bedienungsanleitung

M-system

M-system W2MS Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung