M-system 99SVA Bedienungsanleitung

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

85 – 264V AC rating: 85 – 264V, 50/60 Hz, approx. 75VA

Power consumption: Approx. 12W (excluding that of out-

put current)

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -5 to +45°C

(23 to 113°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

• Be sure to put the terminal cover on while the power is

supplied.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Specifications

Connection Diagram

Body

INSTALLATION unit: mm (inch)

100 (3.94)

120 (4.72)

160 (6.30) min.

4–M4

SCREW

Observe at the minimum of 30 mm (1.2”) for ventilation in all directions.

1A OUTPUT TRANSMITTER MODEL 99SVA

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-1684 Rev.3 P. 1 / 2

INSTRUCTION MANUAL

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the front of the unit.

■EXTERNAL DIMENSIONS unit: mm (inch)

100 (3.94)

202 (7.95)

130 (5.12)

100 (3.94)

120 (4.72)

130 (5.12)

2.5 (.01)

4–R2.5 MTG HOLE

■CONNECTION DIAGRAM

–

INPUT OUTPUT

1 3

FG 5

POWER

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 1.2 N·m

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input voltage: Check voltage across the terminal

6 – 7 with a multimeter.

3) Input: Check that the input signal is within 0 – 100% of

the full-scale.

4) Output: Check that the load resistance meets the de-

scribed speciﬁcations.

ADJUSTMENT PROCEDURE

This unit is calibrated at the factory to meet the ordered

speciﬁcations, therefore you usually do not need any cali-

bration.

For matching the signal to a receiving instrument or in case

of regular calibration, adjust the output as explained in the

following.

■HOW TO CALIBRATE THE OUTPUT SIGNAL

Use a signal source and measuring instruments of sufﬁcient

accuracy level. Turn the power supply on and warm up for

more than 10 minutes.

1) ZERO: Apply 1% input and adjust output to 1%.

2) SPAN: Apply 100% input and adjust output to 100%.

3) Check ZERO adjustment again with 1% input.

4) When ZERO value is changed, repeat the above proce-

dure 1) – 3).

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes. Apply 1%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit according to the “ADJUST-

MENT PROCEDURE” explained earlier.

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

99SVA

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-1684 Rev.3 P. 2 / 2

Andere M-system Sender Handbücher

M-system

M-system Mini-M M2XM2 Bedienungsanleitung

M-system

M-system M5PT Bedienungsanleitung

M-system

M-system F2TS Bedienungsanleitung

M-system

M-system Mini-M M2VF Bedienungsanleitung

M-system

M-system Mini-M M2VS Bedienungsanleitung

M-system

M-system Mini-M M2SP Bedienungsanleitung

M-system

M-system M3LV Bedienungsanleitung

M-system

M-system M5VSH Bedienungsanleitung

M-system

M-system M3LM Bedienungsanleitung

M-system

M-system M3LU Bedienungsanleitung

M-system

M-system W5PA Bedienungsanleitung

M-system

M-system W2VS Bedienungsanleitung

M-system

M-system 27RS Bedienungsanleitung

M-system

M-system Mini-M M2RTS Bedienungsanleitung

M-system

M-system Mini-M M2WVS Bedienungsanleitung

M-system

M-system Mini-MW Series Bedienungsanleitung

M-system

M-system B3HU2 Bedienungsanleitung

M-system

M-system W2XT Bedienungsanleitung

M-system

M-system M2XRP2 Bedienungsanleitung

M-system

M-system 10JRE Bedienungsanleitung

M-system

M-system F2VS Bedienungsanleitung

M-system

M-system VOS2T-R Bedienungsanleitung

M-system

M-system M5PA-CA-R Bedienungsanleitung

M-system

M-system B3VS/2 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung