M-system M5XV Bedienungsanleitung

EM-2762　Rev.2 P. 1 / 3

INSTRUCTION MANUAL

SIGNAL TRANSMITTER

(PC programmable) MODEL M5XV

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Signal conditioner ...............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

The M5XV is programmable using the PC Conﬁgurator

Software. For detailed information on the PC conﬁguration,

refer to the M5CFG users manual. The M5CFG PC Con-

ﬁgurator Software is downloadable at M-System’s web site:

https://www.m-system.co.jp

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside a panel.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

24V DC rating: 24V ±10%, ≤ 1W

■GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power

supply and input signal for safety.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -20 to +65°C

(-4 to +149°F) with relative humidity within 30 to 90%

RH in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

• Install lightning surge protectors for those wires connect-

ed to remote locations.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

TerminalCover

PowerIndicatorLED

ConﬁguratorJack

Body

Speciﬁcation

OutputSettingDIPSW

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

M5XV

EM-2762　Rev.2 P. 2 / 3

INSTALLATION

Set the unit so that its DIN rail adapter is at the bottom.

■MOUNTING THE UNIT ON A DIN RAIL

A)Hang the upper hook at the rear side of unit on the DIN

rail.

B)Push in the lower in keeping pressing the unit to the DIN

rail.

DIN rail

■REMOVING THE UNIT

A)Pull down the DIN rail adaptor using a minus screwdriv-

er.

B)Pull out the lower part of the unit.

C)Remove the upper part from the DIN rail.

Slider

TERMINAL CONNECTIONS

Connect the unit as in the diagram below or refer to the connection diagram on the side of the unit.

■EXTERNAL DIMENSIONS unit: mm [inch]

94 [3.70]3 [.12]

25 [.98] 41 [1.61] (3.3 [.13])

• When mounting, no extra space is needed between units.

DIN RAIL

35mm wide

8–M3.5 SCREW

7.3 [.29]

■CONNECTION DIAGRAM

–

OUTPUT

JACK

–

Configurator Jack

–

POWER

DC Current

Input (Z1)

DC Voltage

Input (S1)

DC Voltage

Input (S2)

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.8 N·m

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

M5XV

EM-2762　Rev.2 P. 3 / 3

EXTERNAL VIEWS

■LEFT VIEW ■FRONT VIEW

DIP SW

SW1

Power Indicator LED

Configurator Jack

OUTPUT RANGING

The internal DIP switch setting is required to select output types before setting a precise output range using PC Conﬁgurator

Software (model: M5CFG).

For detailed information on the PC conﬁguration, refer to the M5CFG users manual.

Table 1. DIP switch setting: Output type

Output

Type

SW1

123456

0 – 20 mA ON OFF OFF OFF ON OFF

-5 – +5 V OFF ON ON OFF OFF ON

-10 – +10 V OFF ON OFF ON OFF ON

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Check DIP switch setting.

3) Power input voltage: Check voltage across the terminal

7 – 8 with a multimeter.

4) Input: Check that the input signal is within 0 – 100% of

the full-scale.

5) Output: Check that the load resistance meets the de-

scribed speciﬁcations.

POWER INDICATOR LED

The transmitter is provided with a power indicator LED

which blinks in different patterns indicating various oper-

ating status.

The following ﬁgure indicates typical patterns.

LEDONOFFPATTERNSTRANSMITTERSTATUS

Downloadingthesetting

Rangesetting

Fineadjusting

Supplyingaﬁxedoutput

Normal

AbnormalOperation

(corruptionofconﬁgurationdata)

80ms

MAINTENANCE

Regular calibration procedure is explained below:

■CALIBRATION

Warm up the unit for at least 10 minutes. Apply 0%, 25%,

50%, 75% and 100% input signal. Check that the output

signal for the respective input signal remains within accu-

racy described in the data sheet. When the output is out of

tolerance, recalibrate the unit using the PC Conﬁgurator

Software (model: M5CFG).

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

056 222 38 18 mailbox@sentronic.com www.sentronic.com

SENTRONIC AG

Andere M-system Sender Handbücher

M-system

M-system M3LR Bedienungsanleitung

M-system

M-system Mini-M M2AMS Bedienungsanleitung

M-system

M-system W5PA Bedienungsanleitung

M-system

M-system M2EXV Bedienungsanleitung

M-system

M-system M3LPA Bedienungsanleitung

M-system

M-system 10JR Bedienungsanleitung

M-system

M-system Mini-M M2CA Bedienungsanleitung

M-system

M-system Mini-MW Series Bedienungsanleitung

M-system

M-system B5RS Bedienungsanleitung

M-system

M-system M3LM Bedienungsanleitung

M-system

M-system W2AC Bedienungsanleitung

M-system

M-system Mini-M M2SP Bedienungsanleitung

M-system

M-system 10JPA Bedienungsanleitung

M-system

M-system W2RS1 Bedienungsanleitung

M-system

M-system M5MS-5-R Bedienungsanleitung

M-system

M-system W5-UNIT Bedienungsanleitung

M-system

M-system 10VS Bedienungsanleitung

M-system

M-system LINEARIZER JFX Bedienungsanleitung

M-system

M-system Mini-M M2XT2 Bedienungsanleitung

M-system

M-system W2XM Bedienungsanleitung

M-system

M-system Mini-M M2UDS Bedienungsanleitung

M-system

M-system JR Bedienungsanleitung

M-system

M-system 6BPA Bedienungsanleitung

M-system

M-system 6LC Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung