M-TI 526 Bedienungsanleitung

Installation and

Operation Manual

MTI 526, 527P/S, & 527W Podiatry Chairs

527 P/S

526

527W

Table of Contents iii

GENERAL INFORMATION......................................................................................................................................................................... 1

Purpose of this Manual...................................................................................................................................................................................................1

Intended Product Use.....................................................................................................................................................................................................1

Symbols and Warnings...................................................................................................................................................................................................1

Transportation and Storage Conditions ..............................................................................................................................................................2

INSTALLATION............................................................................................................................................................................................. 2

READ THIS MANUAL BEFORE INSTALLATION! ...................................................................................................................................................2

Unpacking..............................................................................................................................................................................................................................3

Leveling Feet Adjustements........................................................................................................................................................................................5

Upholstery Installation ..................................................................................................................................................................................................5

CONTROLS & FEATURES .......................................................................................................................................................................... 7

526 Pedestal Base Chair .................................................................................................................................................................................................7

527S Model Chairs.............................................................................................................................................................................................................7

527P Model Chairs ............................................................................................................................................................................................................7

527W Model Chair.............................................................................................................................................................................................................7

ASPECTS OF FOOT CONTROLS ............................................................................................................................................................. 7

OPERATION.................................................................................................................................................................................................. 8

Model 526 Foot/Hand Controls................................................................................................................................................................................8

Model 527S & 527WS Foot/Hand Controls........................................................................................................................................................8

Model 527P & 527WP “Programmable” Power Base Chair........................................................................................................................9

Electrical Lock-Out ............................................................................................................................................................................................................9

Swivel Base Installation ..................................................................................................................................................................................................9

Swivel Base Operation................................................................................................................................................................................................. 10

Foot Section Adjustment........................................................................................................................................................................................... 10

Debris Tray Tension Adjustment............................................................................................................................................................................ 11

Retractable Arms............................................................................................................................................................................................................. 11

Optional Duplex Electrical Outlet.........................................................................................................................................................................11

CLEANING & DISINFECTION.................................................................................................................................................................12

Upholstery........................................................................................................................................................................................................................... 12

Painted Surfaces .............................................................................................................................................................................................................. 12

Plastic Components ...................................................................................................................................................................................................... 12

MAINTENANCE .........................................................................................................................................................................................12

Trouble Shooting ........................................................................................................................................................................................................... 12

Fuse Replacement*........................................................................................................................................................................................................ 12

527W OWNERSHIP ..................................................................................................................................................................................13

Purpose of Section......................................................................................................................................................................................................... 13

Installation........................................................................................................................................................................................................................... 13

SPECIFICATIONS.......................................................................................................................................................................................15

ACCESSORIES ............................................................................................................................................................................................16

LIMITED WARRANTY...............................................................................................................................................................................17

GENERAL INFORMATION

Purpose of this Manual

This manual covers the instructions for the installation and safe operation of these

power exam and procedure tables. It is intended that it be used by the person(s)

installing the equipment and by the medical professionals using it. No repair

information is included with this manual, because no operator repairs are intended.

Intended Product Use

This chair/table is intended to be used as a chair or a table for general examinations

and procedures performed by medical professionals.

Symbols and Warnings

This manual contains Notes, Cautions and some Danger information which are

meant to call attention to particular parts or sections of this manual. Since safety is

our rst concern, this manual should be read by all personnel who will be operating

or placing patients in this table.

NOTES are used to call attention to a condition, practice or procedure.

CAUTIONS are meant to call attention to a condition, practice or procedure which

could cause product damage if not used correctly.

DANGER is used to call attention to any of the above which could cause personal

injury if not followed correctly. Please become familiar with all danger warnings and

observe them at all times.

MTI 526, 527P/S, & 527W

Installation and Operation Manual

2 Installation and Operation Manual |MTI 526, 527P/S, & 527W

GENERAL INFORMATION

CONTINUED

Indicates Class 1, Type B, Medical Equipment

Indicates the proper shipping orientation for

the product.

Indicates that the product is fragile; be careful

in handling.

Indicates a protective earth ground.

Indicates alternating current.

Indicates the unit duty cycle of 10%

Example: (1) minute on (9) minutes o.

Indicates that the product must be kept dry.

Indicates the minimum and maximum storage

temperatures for the unit.

Indicates the maximum stacking height of palleted

units.

Indicates the presence of a dangerous

voltage/shock hazard.

Indicates the operator’s manual should be

consulted for important information.

Transportation and Storage Conditions

Temperature Range:

t 0°C (32°F) to 44°C (110°F)

Relative Humidity:

t 10° to 90° (non-condensing)

Atmospheric Pressure:

t 500 hpa to 1060 hpa (0.49atm to 1.05atm)

INSTALLATION

READ THIS MANUAL BEFORE INSTALLATION!

IF THIS TABLE HAS BEEN EXPOSED TO LOW

TEMPERATURES, ALLOW ADEQUATE TIME FOR IT TO

WARM TO ROOM TEMPERATURE BEFORE PUTTING INTO

SERVICE. INSPECT THE SHIPPING BOXES FOR VISIBLE

DAMAGE. RECORD, PHOTOGRAPH AND REPORT ANY

DAMAGE TO THE CARRIER IMMEDIATELY. REQUEST

AN INSPECTION BY THE CARRIER IF ANY CONCEALED

DAMAGE IS NOTED!

Installation and Operation Manual |MTI 526, 527P/S, & 527W 3

Unpacking

You will need the following to unpack and assemble

your new MTI chair:

t Wire or sheet metal cutters to cut banding

t A medium size Phillips screw driver for installation

of the patient arm upholstery

t 7/16” open or closed box end wrench (also a 5/8”

open or closed wrench and set of allyn wrenches, if

a light post is ordered)

t A utility knife or blade to open the upholstery box

t A medium at blade screw driver

t A pair of needle nosed pliers can also be helpful

1. Open the upholstery box using the utility knife

with the blade only slightly exposed so the

upholstery does not get damaged while cutting

the tape. Inspect the upholstery carefully for any

damage. There should be; (2) upholstered arms,

(1) upholstered back cushion, (1) upholstered

seat cushion, (1) upholstered foot cushion with

scu cover, and (1) upholstery ap, which will go

between the seat and back cushions.

2. Cut the banding on the chair pallet lid and remove

the corrugated box, being careful not to scrape the

chair inside.

3. Using the 7/16” wrench or an adjustable wrench to

loosen the four nuts and remove, along with the

wooden slats holding the base to the wood pallet.

This equipment is heavy, get help to remove it from

the shipping pallet. Use proper lifting procedures when

lifting to avoid serious back injury. Lift the chair from the

retracted foot section and from the exposed male back

clevis protruding from the chair back as it lays over the

seat. Scoot or slide the base to the oor from the pallet.

Avoid lifting from the formed plastic side panels or

foot section levers, as damage to them may result. If the

installation location is on a vinyl or hard tile oor, a piece

of carpet or other material should be placed beside the

pallet to act as a cushion to protect the ooring.

Allow the chair to come to room temperature to

get maximum performance. Prolonged storage at low

temperatures can make the operation slow or even not

function until the motors have warmed up.

4. Remove the foot control from its corrugated

enclosure.

5. The chair is shipped with the back section laying

over on the seat. Grasp the end of the back motor

push tube, while at the same time, cut the cable

tie attaching it to the back actuator levers located

on the bottom lower left side of the chair back.

Remove one of the e-ring fasteners from the

precision pin located in the holes of the back

actuator levers. Raise the back up to approximately

70 degrees vertical to the oor. Align the holes in

the back actuator push tube with the holes in the

actuator levers of the chair back. (Figure 1). Push

the pin through the holes and replace the e-ring.

A hard rubber mallet may be necessary to replace

the pin.

Figure 1

4 Installation and Operation Manual |MTI 526, 527P/S, & 527W

Be extremely careful in this next step of installing the

arm linkage pin, that you do not drop the pin or e-ring

inside the base or you will have to disassemble the covers

to retrieve them.

6. Remove the e-ring and pin from the arm

actuation linkage. With your left hand, or by using

someone to assist you, raise the left patient arm

approximately horizontal. With your right hand pull

the plastic top cover edge outward slightly, and

at the same time, align the pin with the holes in

linkage. Some wiggling up and down of the arm,

while pressing the pin inward may be needed

(Figure 2). After pin is all the way through the

holes, replace the remaining e-ring.

Figure 2

7. Align pins and tabs of the male foot control plug

with the chair receptacle by positioning the

yellow/white mark on the plug body to the twelve

O’clock position relative to the receptacle at the

lower rear of the chair base (Figure 3). Secure the

plug body by rotating the locking ring clockwise

(CW) until it engages and then stops.

Figure 3

Alignment only requires slight pressure; do not force

the male plug into the female receptacle of the base as

damage to one or both plugs can occur.

8. Your MTI chair is equipped with a separate three-

wire electrical supply cord, with a grounded male

plug cap and an IEC320 female plug to the chair. To

install, plug the IEC320 female plug into the chair

and secure with the spring wire keeper (Figure 4).

Then plug the grounded male plug cap and attach

the surge protector to an appropriately protected

115/60 or 230/50 Volt AC grounded outlet. The

AC (alternating current) input is transformed to 24

volts and then rectied to DC (direct current) just

after the power enters the

chair base.

Figure 4

Installation and Operation Manual |MTI 526, 527P/S, & 527W 5

Each MTI chair has a circuit board. The included surge

protector must be used to protect the board. Warranty is

void if this surge protector is not used.

Do not use a two-three plug adapter to plug the MTI

chair into a two conductor outlet, as grounding reliability

is not then maintained.

Do not operate your MTI chair in the presence of

ammable anesthetics.

The supply cord may be used to simultaneously

insolate both poles of the power supply by removing the

power supply cord at the chair input or wall receptacle.

The electro magnet on any optional electro

magnetically operated swivel base has been evaluated for

potential electro magnetic interference and health risks

and found NOT to present any potential problems.

Leveling Feet Adjustments

In order to keep the table’s base level on any type of

surface, your MTI table is equipped with leveling feet

on each corner of the chair base plate.

If you chair is not level or it rocks from side to side, then

adjustement to one or more of the leveling feel will be

required.

1. Position the table where it will be intended to be

used. Check the stability of the table by wiggling

the table top from side to side with the table in the

fully raised position.

2. Use a 5/8” open or closed end wrench to loosen

and remove the plated acorn nuts which are found

on the corners of the base plate (Figure 5).

Figure 5

3. Using a medium at blade screwdriver, turn the

slotted screw under the acorn nut clockwise

(CW) to take up more space under the plate or

counterclockwise (CCW) for less travel (Figure 6).

Figure 6

Adjustments to one or more of the leveling feet may

be needed to be done for optimal results.

Upholstery Installation

Your upholstery kit includes the following upholstery

pieces:

t Back cushion upholstery

t Seat cushion upholstery

t Foot cushion upholstery

6 Installation and Operation Manual |MTI 526, 527P/S, & 527W

t (2) Upholstered arms that come with (8) 10-24 x 1

1/2” screws and (8) #10 internal star washers

t Back/seat cushion ap

If your MTI table is ordered with optional arms,

headrests, lights, etc., those parts will be in a separate box

from the upholstery.

All cushions and the foot cushion scu cover attach to

the chair with Velcro® for easy installation and removal.

While installing all cushions, align Velcro® strips and

cushions with the mating Velcro® strips on the chair

metal section substrates.

4. Power the metal back down to a position in the same

plain as the seat. Install the ap between the seat and

back cushions rst, by laying the ap over the chair

back hinges and securing the ap to the Velcro® strips

of the back and seat cushions (Figure 7).

Figure 7

5. Install the seat cushion by placing the rear of the

cushion rst against the hinges located at the rear

of the seat and then lowering it to the front of

the seat, while aligning the waterfall edges of the

cushion with the formed recesses of the side panel

moldings (Figure 8).

Figure 8

6. Resting the top of the back cushion on the top of

the formed back cushion cover, match the waterfall

cushion to the formed recess of the thermoformed

back panel and lower into place (Figure 9).

Figure 9

7. With the foot section in the retracted position,

place the foot cushion over the metal substrate,

rear rst, while lowering and aligning the cushion

and Velcro® with the metal substrate (Figure 10).

Figure 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere M-TI Medizinische Geräte Handbücher

M-TI

M-TI 550 Bedienungsanleitung

M-TI

M-TI 830 Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung