M2 Antenna Systems EB-432/RK70CM Bedienungsanleitung

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com

Rev.02

Model .........................................EB-432/RK70CM

Frequency Range.......................400 To 470 MHz

Gain, Overhead 90.....................5.5 dBic Typical

Impedance .................................50 OHMS

VSWR.........................................< 2.0:1

VSWR.........................................1.5:1 @ 420– 450 MHz

Pattern........................................Omni Directional

Polarity .......................................RH Circular Overhead

Polarity .......................................Horizontal @ Horizon

Power Handling..........................500W Max

Mounting.....................................1-1/2” to 2” Nom.

Connector...................................“N” Female

Size.............................................13.5” H x 9.5” W

Wind Survival / Wind Area..........100 MPH / .07 Sq. Ft.

Weight / Ship Wt.........................2 Lbs. / 3 Lbs.

M2 Antenna Systems, Inc.

Model No: EB-432/RK70CM

Eggbeater Satellite Antenna

FEATURES:

The EB-432 EGGBEATER offers exciting new performance characteristics for both fixed and mobile operations.

The EGGBEATER produces smooth Omni directional HORIZONTAL polarity at the horizon. Above the horizon, the pat-

tern transforms to RIGHT HAND CIRCULAR, making it a natural for OSCAR satellite use. By spacing the EGGBEATER

1/8 wave above a metal surface or the RK-70CM for base installations, the circular lobe increases by 6 dB, producing a

hemispherical pattern. No rotation or steering is required. For terrestrial mobile, base, net control, contest or field day op-

eration, increasing the distance above ground or over a metallic surface improves the horizontal radiation by up to 6 dB.

This produces instantaneous communications in all directions. Hams with little room or budget for larger antennas will

experience a new standard of performance with the EB-432/RK70CM.

SPECIFICATIONS:

Peak= 5.62 dBi Total Field

Circular Omni Antenna

ElevaƟon

Shown with RK-70CM

Reflector Kit

EB-432/RK70CM ASSEMBLY MANUAL

Caution: The copperweld steel loop elements are packed in a tightly

wrapped condition. Use extreme care while unpacking the loops. Work in a

clear area and be sure no one is standing near during unpacking.

Tool Required: 3/32” and 5/32 Allen wrench (provided) and 1/2 & 9/16 end wrench or socket.

1. To facilitate shipping, the loops are bent slightly in the middle. Straighten these, and any other bends, so

the elements form round circles. Locate the rod and thread the loop elements through the crossed holes in the

tip to their midpoints.

NOTE: be sure the loop elements are not shorted together at the crossover point; the pattern will be distorted.

2. Align the elements carefully with the terminals at the top of the balun case. Install the set-screws with the

3/32” Allen wrench, and insert the ends of the loop wires into the appropriate terminals. Insert wires until ends

butt against the Delrin collar at the base of the fiberglass rod. Tighten the 3/32” set-screws. This completes

assembly. A common mobile mounting 3/8-24 thread in bottom of balun case is used for mounting the EB-

432.

MOBILE INSTALLATION:

For best TERRESTRIAL results in a horizontally polarized mobile installation, the Eggbeater should be at

least two feet above the top of the vehicle, preferably higher. To prevent damage to the antenna or mount, a

heavy duty spring should be installed 4” to 26” below the threaded insert on the balun case. Another mast

section can be added below the spring if additional height is desired. To enhance the overhead circular

pattern for SATELLITE communications, mount the EB-432 loops at 1/8 wave (3.5”) above the roof, basically

at roof level or attached directly to a mag-mount.

FIXED LOCATION INSTALLATION:

For best TERRESTRIAL results, no reflector is

required. Mount the EB-432 as high as possible and

preferably on the top of a mast.

For mostly SATELLITE communications use, add the

RK-70cm Reflector as shown. Alternately, mount the

EB-432 directly on a metal plane of mesh or solid

metal 15” square or larger. Mounting this way will

reduce your terrestrial performance by about 6 dB but

improve your satellite signal by about the same

amount. The Eggbeater produces an omnidirectional,

horizontally polarized pattern, so no particular

orientation is necessary.

EB-432 WITH RK-70CM REFLECTOR

EB-432/RK70CM PART LAYOUT

GENERAL INFORMATION

Feedline should be good quality 50 ohm coax cable. Times LMR-400 and Belden 9913F are excellent low-loss foam

types and RG-8X is also good for short run as in a mobile setup. Connect the male "N" to the Balun case connector and,

if a mast is used, secure the cable to the mast with tape or nylon ties, beginning 4-6 inches below the connector and

repeating every 12” down the mast. Be sure to leave a little slack where the cable passes the spring.

For best performance, 80 watts, or more, are recommended particularly for mobile operation. Contacts with base

stations over 100 miles away are common and communications are possible for over 350 miles when the terrain

permits propagation. The Eggbeater will handle a Kilowatt in base station applications.

Any distortion or bends in the loops incurred during mobile use can and should be straightened out as soon as practical.

AS WITH ANY ANTENNA FED WITH RF ENERGY, AVOID CONTACT OR CLOSE PROXIMITY WHILE

TRANSMITTING.

SATELLITE APPLICATIONS:

1. The Eggbeater is very effective as a omnidirectional satellite antenna because it produces Right-Hand Circular

polarization off the top. When mounted 1/8 wave above an auto roof or M2’s RK-70CM Radial Reflector Kit for base

installations, the signal level off the top lobe increases by as much as 6 dB. No rotation or steering is necessary.

Circularity is optimized in the 420-450 MHz region but is still effective from 400 to 470 MHz.

2. Base station, contest and field day operations with the Eggbeater allows rapid fire communication with all horizontally

polarized stations, in all directions. Its also great for nets and emergency stations requiring instant communications in all

directions. The Eggbeater is not designed to replace a good directional antenna, but where space, time, or budget are

strong factors, it will prove a valuable addition to any station.

3. Experimenters: Try combining the Eggbeater with other vertical antennas. The fiberglass spacer mast is not required

for operation except to insulate the crossover points. It could be replaced with a metallic element to act as a vertical

radiator on 70 centimeters or any other frequency, or simply be used as a support for a vertical above the Eggbeater. It

may be possible to combine the Eggbeater with an HF mobile antenna so that optimum performance of both would be

preserved.

As you can see from the APPLICATIONS, the EGGBEATER is a versatile antenna.....let your imagination run free!

Write and tell us what you have done with your Eggbeater.

Note: #10 Copperweld (steel copper-clad wire) is used in the loops for maximum efficiency. The steel is exposed at

the ends and may show signs of rust in various environments. This effect is cosmetic only but can be reduced by

coating the ends of the wire with epoxy, RTV, Penetrox or equivalent after assembly.

M2ANTENNA SYSTEMS, INC.

4402 N. SELLAND AVE.

FRESNO, CA 93722

(559) 432-8873 FAX: 432-3059

www.m2inc.com Email: [email protected]

EB-432/RK70CM ASSEMBLY MANUAL

NOTE:

OTHER MOUNTING OPTIONS

EB-432/RK70CM PARTS & HARDWARE

DESCRIPTION.........................................................................................QTY

EB-432 BODY ASSEMBLY......................................................................1

LOOP ELEMENTS, #10 COPPERWELD, 29-1/8”....................................2

SET SCREW, 10-32 X 1/4”, SS................................................................4

3/32” ALLEN WRENCH............................................................................1

ASSEMBLY MANUAL ..............................................................................1

RK-70CM REFLECTOR KIT:

REFLECTOR PLATE, 1/2” X 2-1/2” (M23AEB0010)................................1

RADIAL RODS, 1/4” X 9” .........................................................................8

U-BOLT, 2”...............................................................................................2

U-BOLT, 1-1/2”.........................................................................................2

BOOM TO MAST L-PLATE, 4” X 4”, (M2APT0063).................................1

HARDWARE:

BOLT, 3/8-24 X 1”, SS..............................................................................1

LOCKWASHER, 3/8”, SS.........................................................................1

NUT, 5/16-18, SS.....................................................................................4

LOCKWASHER, 5/16”, SS.......................................................................4

SET SCREW, 8-32 X 1/4”, SS..................................................................8

5/64” ALLEN WRENCH............................................................................1

M2ANTENNA SYSTEMS, INC.

4402 N. SELLAND AVE.

FRESNO, CA 93722

(559) 432-8873 FAX: 432-3059

www.m2inc.com Email: [email protected]

Inhaltsverzeichnis

Andere M2 Antenna Systems Antenne Handbücher

M2 Antenna Systems

M2 Antenna Systems 348CP18 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 41-3BB Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 902-14WLC Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 12M4DX Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems FGSD-2.4DH Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 48.5-4 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems Relay/Preamp Housing with MAP65 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 2M4X Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 32 HO LOOP Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 222 HO LOOP Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 35.7-4 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 400CP30A Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 7-10-30LP8 UP-KIT Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 6M7JHVHD Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 137CP14HD Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 432-6WL Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 2068-26-2 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 440-460-11HD Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 432-15WL Kurzanleitung

M2 Antenna Systems

M2 Antenna Systems 440-6SS Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 222XP40 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 11M5DX Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 2M8WL Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems Eggbeater EB-310 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung