M2 Antenna Systems FGSD-3.7DH Bedienungsanleitung

M2 ANTENNA SYSTEMS, INC. 4402 N. SELLAND AVE. FRESNO, CA 93722

TEL: (559) 432-8873 FAX: (559) 432-3059 WEB: WWW.M2INC.COM

REV A

M2 ANTENNA SYSTEMS, INC.

DH SATELLITE DISH MOUNT

MODEL NO: FGSD-3.7DH

SATELLITE DISH MOUNT ASSEMBLY

STEP 1:

Mount one SATELLITE DISH SUP-

PORT to DISH MOUNT BASE PLATE. This

support will need to align with the holes in the

SATELLITE DISH, therefore leave the hard-

ware loose to allow for some adjustment during

assembly.

SATELLITE DISH SUPPORT

STEP 2:

Finish installing the other DISH SUP-

PORTS in a radial pattern. Leave all the hard-

ware finger tight.

BEFORE YOU BEGIN: Look over all the DRAWINGS to get familiar with the various parts

and assemblies in the system. Tools handy for assembly process: 11/32”, 7/16”, 1/2”, 9/16”

and 5/8” spin-tites, end wrenches and/or sockets.

NOTE:

All installations are unique in some way, which means it's OK to preassemble certain hardware, or re-

arrange the assembly process to meet specific site requirements. A quick review of the assembly

notes and drawings should help firm up the appropriate strategy. Please remember to double-check all

hardware for tightness BEFORE it becomes inaccessible.

SATELLITE DISH

MOUNT BASE PLATE

BOLT, 5/16-18 X 1-1/4”

FLAT WASHER, 5/16” (X2)

LOCK WASHER, 5/16”

NUT, 5/16-18

(QTY 2)

SATELLITE DISH

SUPPORT

QTY (8)

STEP 3:

Mount the SATELLITE DISH SUPPORT RING to the top of the SATELLITE DISH

SUPPORTS. Tighten all hardware.

SATELLITE DISH MOUNT ASSEMBLY

SATELLITE DISH

MOUNTING RING

BOLT, 5/16-18 X 5-1/2”

FLAT WASHER, 5/16” (X2)

LOCK WASHER, 5/16”

NUT, 5/16-18

QTY (16)

SATELLITE DISH MOUNT ASSEMBLY

SATELLITE DISH ASSEMBLY

STEP 4:

The SATELLITE DISH PANELS come with color coded

dots on the rib to indicate which panels need to be mated to-

gether for proper alignment. Each dot is labeled with serial num-

bers and matching rib numbers.

STEP 5:

The method recommended for assem-

bling the SATELLITE DISH PANELS requires

placing a stand, which is provided, at the cen-

ter of panels. It does not matter which panels

you start with as long as they both have the

same numbers labeled on the corresponding

ribs. Carefully place two panels with mating

numbers touching onto the stand

RIB IDENTIFICATION

(MATE WITH PANEL WITH SAME NUMBER)

SATELLITE DISH SERIAL NUMBER

(WILL BE DIFFERENT FOR YOUR DISH)

ASSEMBLY STAND

(PROVIDED)

STEP 6:

Insert the fasteners provided into the

holes connecting the two SATELLITE DISH

PANELS together. Leave the fasteners finger

tight until all PANELS are assembled. Continue

adding another panel with a corresponding rib

number that matches one of the already as-

sembled PANELS. Insert the fasteners into the

THIRD PANEL. Leave fasteners finger tight. Do

not add the FOURTH PANEL yet. You will need

to add the hub assembly and need to access

the center of the dish for ease of assembly.

BOLT, 1/4-20 X 3/4”, SS

LOCK WASHER, 1/4”, SS

NUT, 1/4-20, SS

QTY (52)

SATELLITE DISH ASSEMBLY

STEP 7:

Install the UPPER SUPPORT ROD TAB into the rim of the SATELLITE DISH. Install all

remaining TABS. Tighten all hardware.

BOLT, 1/4-20 X 3/4”

FLAT WASHER, 1/4”

LOCK NUT, 1/4-20

(QTY 16)

UPPER SUPPORT

ROD TAB

(QTY 8)

SATELLITE DISH

STEP 8

Attach the partially assembled SATELLITE DISH to the DISH ASSEMBLY MOUNT. It

may not be possible to reach all the BOLTS to attach the SATELLITE DISH to the DISH AS-

SEMBLY MOUNT. Once the SATELLITE DISH MOUNT is attached to the BOX FRAME, the

assembly can be positioned to finished attaching all the fasteners.

STEP 9

Use the methods from STEP 6 to attach the final SATELLITE PANEL. Make sure the

holes in the SATELLITE DISH PANEL line up with the SATELLITE DISH MOUNT. Leave the

fasteners finger tight.

SATELLITE DISH ASSEMBLY

BOLT, 3/8-16 X 1-1/4”

FLAT WASHER, 3/8” (X2)

LOCK WASHER, 3/8”

NUT, 3/8-16

SATELLITE DISH

MOUNT ASSEMBLY

SATELLITE DISH ASSEMBLY

STEP 10:

Carefully attach the SATELLITE DISH with MOUNT to ANTENNA POSITIONER. Hard-

ware needed will be part of the ANTENNA POSITIONER ASSEMBLY. Once SATELLITE

DISH MOUNT is properly attached to POSITIONER, position the SATELLITE DISH to 90°

from horizon. Finish securing SATELLITE DISH to SATELLITE DISH MOUNT. Tighten all

hardware.

NOTE: Positioner in graphic may differ for your system.

AE2000

BOLT, 3/8-16 X 1-1/4”

FLAT WASHER, 3/8” (X2)

LOCK WASHER, 3/8”

NUT, 3/8-16

BOLT, 3/8-16 X 1-1/4”

FLAT WASHER, 3/8” (X2)

LOCK WASHER, 3/8”

NUT, 3/8-16

QTY (8)

DISH SUPPORT ROD ASSEMBLY

STEP 11:

Pre-Assemble the DISH SUPPORT ROD ASSEMBLY. Make sure there is a RIGHT HAND

CLEVIS on one end of the assembly as well as a LEFT HAND CLEVIS on the other end of the DISH

SUPPORT ROD ASSEMBLY. Assemble all the DISH SUPPORT ROD ASSEMBLIES. Leave the JAM

NUTS loose for now.

RH TUBE ADAPTER

LH CLEVIS

RH CLEVIS

RH JAM NUT, 3/8-24 SCREW, #8-32 X 1”

LOCK NUT, #8-32

SUPPORT TUBE

LH JAM NUT, 3/8-24

LH TUBE

ADAPTER

SCREW, #8-32 X 1”

LOCK NUT, #8-32

SATELLITE DISH ASSEMBLY

STEP 12:

Attach all the DISH SUPPORT ROD ASSEMBLIES to the UPPER SUPPORT ROD TABS and

SATELLITE DISH SUPPORTS.

STEP 13:

Refer to the tuning section of the manual if you need to tune the SATELLITE DISH. If you do not

wish to tune the SATELLITE DISH, with all the DISH SUPPORT ROD ASSEMBLIES unloaded, start

with one ROD and hand tighten the ROD until it begins to load in tension. Turn the ROD an additional

180 degrees. Tighten the JAM NUTS on the CLEVISES to keep the DISH from detuning. Then working

in a star pattern load the remaining SUPPORT ROD ASSEMBLIES in tension. Careful not to over tight-

en the SUPPORT ROD ASSEMBLIES as this can de-tune the SATELLITE DISH.

BOLT, 5/16 X 1”

LOCKNUT, 5/16”

BOLT, 5/16 X 1”

LOCKNUT, 5/16”

DISH SUPPORT ROD

ASSEMBLIES

(QTY 8)

SATELLITE DISH TUNING

NOTE:

Once the SATELLITE DISH is secured to the POSITIONER, the DISH may require tuning. Using a

ladder or manipulating the DISH with the ANTENNA POSITIONER look at the rim of the DISH. Make

sure the rim of the DISH is uniformly flat across the perimeter. Carefully look at all mating junctions of

the DISH sections and verify there are no highs or lows that could effect the ANTENNA’S performance.

If a high or low spot is noticed slight tuning of the DISH may be needed. If the DISH was properly as-

sembled on a flat surface tuning of the DISH is not usually required.

STEP 1:

Before tuning the satellite DISH make sure the DISH SUPPORT RODS are all unloaded. You will

need 4 pieces of string slightly longer than the diameter of the DISH, approx. 17 feet in length per piece.

STEP 2:

Run 1 piece of string pulled taut connecting opposing SUPPORT ROD TABS. Now place another

piece of string connecting two opposing SUPPORT ROD TABS. The two strings should touch in the

center if the DISH is perfectly flat and the strings are properly taut.

STEP 3:

Now string an additional 3rd and 4th string to the remaining SUPPORT ROD TABS. All 4 pieces

of string should be slightly touching in the center of the DISH. Be careful to notice if one piece of string

is pushing all the other strings up or down.

STEP 4:

If you notice one piece of string is higher or lower than the other strings, that SUPPORT ROD

PAIRING will need to be adjusted. First load one of the SUPPORT RODS that need to be adjusted in

tension slightly. (Using your right hand turn the SUPPORT ROD counter-clockwise). Once you feel the

SUPPORT ROD starting to load in tension turn the SUPPORT ROD an additional 180 degrees and

stop. Next adjust the SUPPORT ROD that is connected to the other end of the string of the SUPPORT

ROD you just loaded. Turn the SUPPORT ROD while noticing the string moving up and down as you

adjust the SUPPORT ROD length. Lengthen or shorten the SUPPORT ROD until the string just touches

the opposing strings.

STEP 5:

Continue tuning additional SUPPORT RODS if necessary until all strings are touching. Tighten

the JAM NUTS on all the SUPPORT RODS once the system is tuned.

Andere M2 Antenna Systems Antenne Handbücher

M2 Antenna Systems

M2 Antenna Systems 11M5DX Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 23CM22EZB Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 2MXP20 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems FG170-230-5 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 20M5-125 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 440-18X Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 40M3FS Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems Eggbeater EB-310 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems FG2227-21X4CP Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 440-460-11HD Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 902-5 YAGI Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 6M HO LOOP Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 500-1000-10 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 167XP22 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 440-11X Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 400-800-8 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 44.5-5 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 6.9-4CDD-125 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 2MCP8A Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 420-450-11HP Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 2M7X Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 35.7-4 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 2MCP22 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 17M5DX Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung