M2 Antenna Systems 303CP26 Bedienungsanleitung

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com

Rev.03

Model .........................................303CP26

Frequency Range.......................298 To 308 MHz

*Gain ..........................................15.14 dBic

Front to back ..............................20 dB Typical

Beamwidth ...............................30° Circular

Feed type ...................................“T” Match

Feed Impedance. .......................50 Ohms Unbalanced

Maximum VSWR........................1.5:1

Input Connector..........................“N” Female

Power Handling ..........................1.5 kW

Boom Length / Dia......................140.625” / 1”

Maximum Element Length..........20”

Turning Radius: ..........................Call

Stacking Distance.......................Call

Mast Size....................................1-1/2” to 2” Nom.

Wind area / Survival ...................0.6 Sq. Ft. / 100MPH

Weight / Ship Wt.........................5 Lbs. / 7 Lbs.

M2 Antenna Systems, Inc.

Model No: 303CP26

FEATURES:

The 303CP26 is a practical sized, yet high performance circular polarized antenna with a remarkably clean pattern. The

pattern is important in order to match the antenna’s noise temperature with modern low noise preamps. This antenna is

ideal for satellite work but is also excellent for terrestrial uses.

The CNC machined driven element module is O-ring sealed and weather tight for low maintenance and long-term peak

performance. Internal connected are encapsulated in a space-age silicone gel that seals out moisture and improves

power handling. The 3/16” 6061-T6 rod elements are centered to minimize interaction and maintain good ellipticity.

Insulators are UV stabilized and locked in place with stainless keepers. Rugged construction, uncompromising

performance for the boom length.

SPECIFICATIONS:

*Subtract 2.14 from dBi for dBd

303CP26 ASSEMBLY MANUAL

Before beginning assembly, read over the parts list and check for missing or damaged parts. Contact the M2

Antenna Systems, Inc. directly at 559-432-8873 if any discrepancy is found.

Tools required: A medium size flat blade screwdriver, an 11/32 nut driver or equivalent, a 1/2 inch wrench or not

driver, a 7/16 inch wrench and a tape measure.

1. The driven element is partially assembled at the factory. Starting 11-3/8” (11.375”) from the rear of the

female “F” connectors point toward the front of the antenna. Secure with an 8-32 x 1-1/4” screw. Next, slide

the 3/16 x 18.0 inch long rod through the open holes just below it and add two black button insulators. Cen-

ter the rod in the boom. Add the shorting blocks, positioning them at the ends of the shorter rod elements.

When everything is adjusted, tighten up the set screws.

2. Repeat this operation for the second driven element, mounting it a t 20-3/8” (20.375”) from the rear and with

the two “F” connectors facing the rear driven element just installed and on the left side of the boom per the

sketch. Proper positioning per the sketch will guarantee RIGHT HAND CIRCULARITY.

3. Assemble the boom per the antenna dimension sheet, secure the joints with the 8-32 x 1-1/4” screws,

lockwasher and nuts. Final tightening and alignment will be done after the elements are all in place.

4. Now mount the phasing block 9-1/4 inches from the rear of the boom using an 8-32 x 1/4” screw. Position the

block on the same side of the boom as the rear driven element so the large “N” connector is facing to the rear.

REFER TO THE CABLE ASSEMBLY SKETCH FOR STEPS 6, 7 & 8.

5. Connect the two 14.5 inch long balun cables to the two close spaced connectors on each driven element

block. Tighten the connectors first by hand and then gently but firmly with a 7/16 inch end wrench. TO

PREVENT POSSIBLE CABLE DAMAGE hold the body of the connector with pliers so it doesn’t rotate during

this final tightening operation.

6. Connect the long, 22-1/2” phasing cable to the single TOP connector on the FRONT driven element and

route the cable back to the side connector on the phasing block. Again, tighten both ends first by hand and then

finally with the 7/16 inch wrench.

7. Connect the short 7-1/2 inch phasing cable to the single connector on the rear driven element block and

route the cable to the in line connector on the phasing block. Tighten as before.

8. Once the cables are all in place form them neatly against the boom and hold in place with the black nylon

ties. In places where director rod elements will come through the boom, do not tighten the nylon ties all the way

so the cables may be moved slightly for clearance around the rod elements.

INSTALLING THE ELEMENTS

9. Separate te rod elements into two (2) sets. Using just one set, install the 18-7/8” rod element in 5/16 inch di-

ameter hole 5 inches form the rear of the boom. Use the black button insulators on either side where the ele-

ment passes through the boom. At this time just position the element near center. Final centering can be done

later when all the elements in one plane are in place.

10. The elements taper in length so continue installing the rods down the boom using the button insulators as

described in step #10.

11. When all the elements in one plane are in place, start at one end using a tape measure: center each

element to 1/16 inch or better. We recommend you DO NOT install the keepers at this time, just center each

element. When centering is complete, stand at the end of the boom and sight down the tips of the elements

noting any irregularities. The tips should form a gentle curve, and each side should look like a mirror image of

the other. This is just a crude check to catch major errors or any irregularities. Correct if found.

303CP26 DIMENSION SHEET

H V

303CP26 ASSEMBLY MANUAL

12. The stainless steel element keepers are stiff so grasp the element firmly while sliding the keepers in place.

USE THE 3/8 X 3 TUBE TO AID IN THE INSTALLATION. Double check your centering dimensions and them

push the keepers up tight against the button insulators.

13. Repeat steps 10 through 13 for the other set of elements.

14. Now that all the elements are in place, sight down the boom looking for element alignment irregularities

around the boom splice joints. Align and tighten.

15. Pick up the boom and find the weight balance point. Remember the feedline will attach at the rear and add

a bit more weight on that end. Position the boom to mast plate accordingly, attaching it to the boom with the 1-

1/8 inch U-bolts, cradles and nuts.

16. Circular polarized antennas such as this antenna must be mounted on non-metallic masts or support booms

and the feedlines must run off the back of the boom so as not to disturb the standing wave ratio and the circular

properties of the antenna. If this antenna is to be mounted as a pair of transmit-receive antennas a 6 to 8 foot

long by 1-1/2 inch diameter crossboom is recommended. When attaching the main 50 Ohm feedline, tape or

nylon tie it securely to the rear stub of the boom to remove stress on the male “N” connector.

THIS ANTENNA HAS BEEN CAREFULLY MANUFACTURED BY:

M2 Antenna Systems, Inc.

4402 N. Selland Ave.

Fresno, CA 93722

(559) 432-8873 Fax (559) 432-3059

www.m2inc.com email: [email protected]

303CP26 PARTS & HARDWARE

303CP26 PARTS LIST

DESCRIPTION .............................................................................. QTY

BOOM SECTION, 1.0” X .058 X 60” SOE ..................................... 1

BOOM SECTION, 1.0” X .058 X 58” SOE ..................................... 1

BOOM SECTION, 1.0” X .058 X 27.625” STR .............................. 1

ELEMENT SET, 3/16” X SEE DIMENSION SHEET ..................... 26

DRIVEN ELEMENT ASSEMBLY................................................... 2

PHASING BLOCK.......................................................................... 1

BALUN, 14.5” RG-6 ....................................................................... 2

PHASING CABLE, 22.5” RG-6 ...................................................... 1

PHASING CABLE, 7.5” RG-6 ........................................................ 1

BOOM TO MAST PLATE, .188 X 4” X 6” ...................................... 1

U-BOLT, 1-1/2” AND CRADLE ...................................................... 2

U-BOLT, 1-1/8” AND CRADLE ...................................................... 2

ASSEMBLY MANUAL.................................................................... 1

HARDWARE BAG

SHORTING BARS, 1/4 X 3/4 X 1-1/2 ALUMINUM........................ 4

BUTTON INSULATORS ................................................................ 52

ELEMENT KEEPERS .................................................................... 52

SCREW, 8-32 X 1-1/4 SS.............................................................. 7

SET SCREW, 8-32 SS................................................................... 8

LOCKWASHER, SPLIT-RING #8 .................................................. 4

NUT, 8-32 SS................................................................................. 4

NUT, 5/16-18 SS............................................................................ 8

LOCKWASHER, 5/16-18 SS ......................................................... 8

NYLON TIE .................................................................................... 5

PUSH TUBE, 3/8 X 3”.................................................................... 1

ALLEN WRENCH, 5/64 ................................................................. 1

M2ANTENNA SYSTEMS, INC.

4402 N. SELLAND AVE.

FRESNO, CA 93722

(559) 432-8873 FAX: 432-3059

www.m2inc.com Email: [email protected]

Inhaltsverzeichnis

Andere M2 Antenna Systems Antenne Handbücher

M2 Antenna Systems

M2 Antenna Systems 75-5AS Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 450-800-12 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 44.5-5 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 432-15WL Kurzanleitung

M2 Antenna Systems

M2 Antenna Systems 249CP24 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 6M7JHVHD Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 6M3 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 40M2C Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 440-6SX Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 2M5-440XP Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 35.7-4 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 436CP16 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 420-50-11 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 25M4 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 80M2L Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 403CP20 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 440-18 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 20M5-125 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 32 HO LOOP Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 40M3L Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 20M6-125 Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems EB-432/RK70CM Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems 2M5WL Bedienungsanleitung

M2 Antenna Systems

M2 Antenna Systems Eggbeater EB-310 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung