MakerBot Labs Experimental Extruder Bedienungsanleitung

CONFIGURATION AND NOZZLE CHANGING GUIDE

NOTE: The Experimental Extruder is an experimental product and is not covered under warranty or MakerCare.

STEP ONE:

Choose your Experimental Extruder configuration:

Remove the

Active Cooling Duct

by pulling down.

Ensure the Replicator Z18

Swivel Clip is attached.

You may optionally remove

the Replicator Z18 Swivel

Clip and replace it with the

Extruder Top Cap

(may perform better with

certain materials).

Remove the Replicator

Z18 Swivel Clip and

replace it with the

Extruder Top Cap.

Make sure the Active Cooling

Duct is snapped into place —

opening toward the back.

›MakerBot®Labs™Experimental Extruder

›Active Cooling Duct (installed)

›MakerBot®Replicator®Z18 Swivel Clip

(installed)

›Extruder Top Cap

UPON UNBOXING YOUR EXPERIMENTAL EXTRUDER PACKAGE, YOU SHOULD

HAVE THE FOLLOWING COMPONENTS:

›Two Nozzle Wrenches

›0.4 mm Brass Nozzle (installed)

›0.6 mm Brass Nozzle

›0.8 mm Brass Nozzle

›0.6 mm Stainless Steel Nozzle

BEFORE YOU START:

Download and 3D print the Experimental Extruder Jig using your standard PLA configuration for a steady base

during Nozzle changing. (thingiverse.com/thing:2557034)

MAKERBOT REPLICATOR+, MINI+

REPLICATOR (5TH GEN), MINI 3D PRINTERS:

MAKERBOT REPLICATOR

Z18 3D PRINTER:

PAGE 2EXPERIMENTAL EXTRUDER CONFIGURATION AND NOZZLE CHANGING GUIDE

STEP THREE:

Wearing heat resistant gloves

remove the hot Experimental

Extruder from the 3D printer

carriage and place into the

Experimental Extruder Jig.

STEP FOUR:

Use the large side of one

Nozzle Wrench to grasp the

flats on the thermal core cone

(adjacent to the Nozzle).

STEP TWO:

Attach the Experimental Extruder

to the carriage of your MakerBot

3D printer and run the

Preheat function.

PRO TIPS:

Some materials may cling to the

Nozzle, to avoid this load and then

unload MakerBot PLA filament to

purge the Nozzle.

Once hot, you may want to scrape any

caked filament off of the Nozzle using

forceps or another tool.

CAU T IO N :

Always wear heat resistant gloves

and protective eyewear when

handling a hot Nozzle.

PAGE 3EXPERIMENTAL EXTRUDER CONFIGURATION AND NOZZLE CHANGING GUIDE

STEP SIX:

Loosen the Nozzle with the two

Nozzle Wrenches but do not

completely remove — allow the

Nozzle to cool.

STEP SEVEN:

Once the loosened Nozzle has

cooled, remove it completely,

then screw on the replacement

Nozzle of choice and

hand-tighten.

STEP FIVE:

Use the small side of the

second Nozzle Wrench to grasp

the Nozzle.

PAGE 4EXPERIMENTAL EXTRUDER CONFIGURATION AND NOZZLE CHANGING GUIDE

STEP NINE:

Reattach the Experimental

Extruder to the 3D printer’s

carriage and run the Z-Calibrate

function. You are now ready

to load you 1.75 mm diameter

filament of choice

and print.

STEP EIGHT:

Heat the Experimental Extruder

on your 3D printer using the

Preheat function, then place the

Experimental Extruder back into

the Experimental Extruder Jig and

wrench tighten the Nozzle one

additional 40° turn.

PAGE 5EXPERIMENTAL EXTRUDER CONFIGURATION AND NOZZLE CHANGING GUIDE

For additional resources and

up-to-date information, visit

MakerBot.com/Labs

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere MakerBot 3D-Drucker Handbücher

MakerBot

MakerBot Thing-O-Matic Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

MakerBot

MakerBot Replicator Mini+ Bedienungsanleitung

MakerBot

MakerBot Replicator Z18 Bedienungsanleitung

MakerBot

MakerBot Replicator 2 Bedienungsanleitung

MakerBot

MakerBot Replicator Z18 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

MakerBot

MakerBot Replicator 2 Bedienungsanleitung

MakerBot

MakerBot Replicator 2 Bedienungsanleitung

MakerBot

MakerBot Replicator Mini Bedienungsanleitung

MakerBot

MakerBot Replicator 2X Bedienungsanleitung

MakerBot

MakerBot Replicator 2X Bedienungsanleitung

MakerBot

MakerBot Replicator Mini+ Bedienungsanleitung

MakerBot

MakerBot METHOD Bedienungsanleitung

MakerBot

MakerBot Replicator 2 Bedienungsanleitung

MakerBot

MakerBot Sketch Bedienungsanleitung

MakerBot

MakerBot Replicator Z18 Bedienungsanleitung

MakerBot

MakerBot Smart Extruder+ Bedienungsanleitung

MakerBot

MakerBot Replicator 2 Leitfaden

MakerBot

MakerBot Replicator Bedienungsanleitung

MakerBot

MakerBot Replicator+ Montageanleitung

MakerBot

MakerBot Replicator Mini+ Bedienungsanleitung

MakerBot

MakerBot Replicator 2X Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch

LONGER

LONGER LK4 Pro Bedienungsanleitung