21
43
Symbol SLR-11 ROP-04
RNK-02 180 m 200 m
RNK-04 180 m 200 m
RNK-02
Wireless Push Button, 2 Channel
EN
99 170 10Model: RNK-02
AF-JZ/JA-160718
FEATURES
MOUNTING, FUNCTIONING
APPEARANCE
• 2-channel button radio transmitter,
• Remote control of EXTA FREE receivers,
• Possibility of independent control of two receivers,
• Wide range of operation (up to 250 m),
• Battery powered,
• Easy installation and mounting possibility in any place,
• Sending information and battery status are optically signalled,
• Possibility of simultaneous switching on / off of any number of EXTA FREE
receivers.
COOPERATION AND OPERATION RANGE
CAUTION: The given range concerns open area - an ideal condition without any
natural or artificial obstacles. If there are some obstacles between a transmit-
ter and a receiver, it is advisable to decrease the range according to: wood and
plaster - from 5 to 20, bricks - from 10 to 40 %, reinforced concrete - from 40
to 80%, metal - from 90 to 100% , glass - from 10 to 20%. Over- and under-
ground medium and high electrical power lines, radio and television transmitters,
GSM transmitters set close to a device system have also a negative influence on
the range.
TECHNICAL DATA
Optical signalling of
transmitter’s operation
Button
Base
Fig. 1
Fig. 2 Fig. 3
BATTERY CHANGE
Battery discharge status is signalled by several LED red
diode flashes during transmission time.
1. Remove the button (Fig. 1).
2. By means of a screwdriver lever up the printed-circuit board releasing the bot-
tom latch (Fig. 2), and remove it from the base.
3. Remove the battery from the latch (Fig. 3).
4. Mount a new battery. Watch battery polarisation marked on the latch. Wrong
battery mounting may cause device damage.
5. Put the removed printed-circuit board back in the base.
6. Put the button back.
CAUTION: While changing the battery, it is suggested to press any of the but-
tons for about 5 seconds before putting it into a latch. Next press transmission
button several times to check its operation. If the transmitter does not work
properly repeat the battery change procedure.
By pressing the button, the transmitter sends a signal with 868.32 MHz frequency
which controls EXTA FREE receivers. Device programming procedure (adding a
transmitter to a receiver’s memory) is described in particular EXTA FREE manual
instructions.
The device can be mounted in any place by means of double-sided adhesive tape
or wall plugs 5 x (3 x 30) mm.
Mounting by means of wall plugs:
1. Remove the button - to do it press the
button
on one side, and on the other side put a
screwdriver into a slot and lift up the
button (Fig. 1)
2. Find a place on the wall to mount
the transmitter, make two holes
corresponding mounting holes
from the transmitter’s base.
3. Set wall plugs in the holes.
4. Fix the base by means of
screwing screws into
wall plugs.
5. Place the button again.
99 170 10
Input rated voltage: 3V DC
Battery type: CR2032
Battery working life: 3 ÷ 5 years (depending on use)
Number of channels:
2
Transmission: radio 868.32 MHz
Transmission way: unidirectional
Coding: addressing transmission
Range:
up to 250 m in the open area
Optical signalling of transmission/battery
discharge: LED red diode
Ambient temperature:
-10 ÷ +55ºC
Operating position: free
Casing mounting: wall plugs, double-sided adhesive tape
IP rating:
IP20 (EN 60529)
Protection class:
III
Pollution degree:
2
Dimensions: 90 x 80 x 11.5 mm
Weight: 0.038 kg
Reference standard: ETSI EN 300 220-1,
ETSI EN 300 220-2
Malmbergs Elektriska AB, PO Box 144, SE-692 23 Kumla, SWEDEN
Phone:
+46
(0)19
58
77
00
Fax:
+46
(0)19
57
11
77
[email protected] www
.malmbergs.com
Co-operation
with EXTA FREE
transmitters
