Malmsten MULTI PRO Junior Bedienungsanleitung
Art. No. 1511026www.malmsten.com/en-US
Malmsten Inc • www.malmsten.com/en-US
Assembly Instructions
Water Polo Goal
MULTI PRO Junior 2.5 m (1511026)
v.14-22
Art. No. 1511026www.malmsten.com
Malmsten AB • www.malmsten.com
TOOLS AND EQUIPMENT REQUIRED TOOLS AND EQUIPMENT RECOMMENDED (OPTIONAL)
Hex key #5 (included)
Hex key #6 (included)
Flat spanner 13 (included)
Cordless screwdriver with hex bits
Blankets, soft lining or protection tiles (velour surface)
RECOMMENDED SAFETY CLOTHING (to be worn during the installation and maintenance)
Steel toe work boots
Working gloves
1. Crossbar
Left
1
2. Crossbar
Right
1
3. Bottom
rear frame
Left
1
4. Bottom
rear frame
Right
1
5. Goal’s
posts
2
6. Bottom
side frame
2
7. Aluminum
pipe right
1
8. Aluminum
pipe right
1
9. Net hanger 2
10. Aluminum
connector
6
Art. No. 1511026www.malmsten.com
Malmsten AB • www.malmsten.com
11. Stain-
less steel
connector
2
12. Top hinge 2
13. Bottom
hinge
2
14. Distance
plate
2
15. Connector
90x15x6
2
16. Plastic
knob M8
2
17. Plastic
inner knob
2
18. Hex socket
button cap
screw
M8x16
72
19. Hex socket
cap screw
M8x60
2
20. Hex socket
cap screw
M8x100
2
21. Hex socket
cap screw
low head
M8x20
4
22. Hex socket
cap screw
M8x40
1
23. Hex socket
cap screw
M8x12
1
24. Hex socket
button cap
screw
M8x55
4
25. Hex socket
cap screw
M8x45
2
26. DIN 934
M8 nut
10
27. DIN 557
M8 nut
14
28. DIN 985
M8 nut
6
29. Rivet nut
(already
installed in
the profile)
8
30. White
plastic
washer
4
Art. No. 1511026www.malmsten.com
Malmsten AB • www.malmsten.com
31. DIN 125
A8,4
washer
8
32. DIN 9021
A8,4
enlarged
washer
4
33. Pontoons
(floats)
2
34. Plastic plug 2
35. Eyelet
screw
4
36. Black
plastic
washer
4
37. Net hook
”Omega”
50
38. Hex key #5 1
39. Hex key #6 1
40. Flat
spanner
13 mm
1
41. Rubber
net strap
1
42. Net 1
I - Preparations
1.1 Prepare the tools and put on your necessary safety clothing
1.2 Cover the floor with blankets / soft lining / protection tiles in order to prevent eventual product
or floor damages
1.3 Unpack the product and lay it down safely on the prepared floor
1.4 Check carefully if any of the delivered items are damaged or missing (a list of components can be
found above)
Please Note: Once the goal is assembled correctly, and upon your next goal inspection (recommended approx.
once a week) you should go over and retighten all bolts.
Certain bolts can benefit from retightening and sometimes the additional application of a product like Loctite.
Loctite, is like a glue, and will lock permanently the bolts in its position.
Loctite can be purchased in most hardware stores.
Important when using Loctite: We ask you to please observe that Loctite should only be used on the bolts high-
lighted in yellow in this document, and Loctite should never be applied to the bolts highlighted in red.
Art. No. 1511026www.malmsten.com
Malmsten AB • www.malmsten.com
II - Assembly
2.1 Assembling the front frame
Assemble the crossbar using:
1. Crossbar left (1) – 1 pcs
2. Crossbar right (2) – 1 pcs
3. Aluminum connector (10) – 1 pcs
4. Connector 90x15x6 (15) – 1 pcs
5. Hex socket button cap screw (18) – 8 pcs
6. Enlarged washer (32) – 2 pcs
7. Hex socket cap screw M8x12 (23) – 2 pcs
Do not tighten all the screws yet. This
must be done after all the assembly
process is complete.
2.2 Assemble the crossbar with posts using:
1. Pre-assembled crossbar – 1 pcs
2. Post (5) – 2 pcs
3. Aluminum connector (10) – 2 pcs
4. Hex socket button cap screw (18) – 16 pcs
2.3 Assembling the bottom (net support) frame
Assemble the rear bottom frame using:
1. Bottom frame left (3) – 1 pcs
2. Bottom frame right (4) – 1 pcs
3. Aluminum connector (10) – 1 pcs
4. Connector 90x15x6 (15) – 1 pcs
5. Hex socket button cap screw (18) – 8 pcs
6. Enlarged washer (32) – 2 pcs
7. Hex socket cap screw M8x12 (23) – 2 pcs
Loctite can be used to permanently lock the bolts in its position.
Art. No. 1511026www.malmsten.com
Malmsten AB • www.malmsten.com
2.4 Connecting the front frame with the bottom frame
Place the top hinges on the front frame using: Place the bottom hinges on the front frame using:
1. Top hinge (12) placed in the top left and right
corners of the front frame – 2 pcs
2. Hex socket button cap screw (18) – 4 pcs
3. M8 square nut (27) – 4 pcs
1. Bottom hinge (13) – placed in the bottom left and right corners of the
front frame – 2 pcs
2. M8 square nut (27) – 4 pcs
3. Distance plate (14) – 2 pcs
4. Hex socket cap screw with low head (21) – 4 pcs
Connect the pre-assembled rear frame with the
bottom side frames using:
1. Rear frame – 1 pcs
2. Side frame (6) – 2 pcs
3. Aluminum connector (10) – 2 pcs
4. Hex socket button cap screw (18) – 16 pcs
Loctite can be used to permanently lock the bolts in its position.
Art. No. 1511026www.malmsten.com
Malmsten AB • www.malmsten.com
Connect the bottom frame with hinges using:
1. Hex socket cap screw (20) – 2 pcs
2. White plastic washer (30) – 4 pcs
3. Self-locking nut (28) – 2 pcs
2.5 Attaching the net support pipes
Take the stainless steel connectors (11) and connect them to
the rear bottom frame:
1. Hex socket button cap screw M8x16 (18) – 4 pcs
2. M8 square nut (27) – 6 pcs* (3 pcs on each side of the
goal)
* Place two additional M8 square nuts into the groove of the
profile to be used later!
Connect the net pipes (9) to the pre-installed top hinges (12)
using:
1. Hex socket cap screw M8x60 (19) – 2 pcs
2. White plastic washers (30) – 4 pcs
3. DIN 125 A8,4 washer (31) – 2 pcs
4. DIN 985 M8 nut (28) – 2 pcs
Connect the net pipes (9) to the pre-installed connectors (11) using:
1. Plastic knob M8 (16) – 2 pcs
2. Plastic inner knob (17) – 2 pcs
Put the 80x40 mm plastic plug into the profile.
Loctite can be used to permanently lock the bolts in its position.
Art. No. 1511026www.malmsten.com
Malmsten AB • www.malmsten.com
2.6 Attaching the reinforcement pipe
Use hex socket cap screws (25) and M8 nuts (28) to connect the reinforcement pipes described as 7 and 8.
Now you may connect the pre-assembled pipe to the
bottom frame using M8 square nut (27) and hex socket cap
screw M8x40 (22) – 2 pcs. that is previously placed in the
profile’s groove.
Loctite can be used to permanently lock the bolts in its position.
Art. No. 1511026www.malmsten.com
Malmsten AB • www.malmsten.com
2.7 Assembling the floats
Put the floats (33) on the bottom frame as per picture on the left and
assemble them using:
1. Hex socket button cap screw M8x55 (24) – 4 pcs
2. DIN 934 M8 nut (26) – 8 pcs
3. Eyelet screw (35) – 4 pcs
4. Black plastic washer (36) – 8 pcs
Do not use Loctite on the bolts.
Art. No. 1511026www.malmsten.com
Malmsten AB • www.malmsten.com
2.8 Attaching the rubber net strap
• Loosen the net hangers at the bottom
• Thread on the rubber net strap (41)
• Put back the net hangers and attach
them again at the bottom
• Move the rubber net strap up into
position
2.9 Attaching the net
• Attach the net hook ”Omega” to the
net
• Space them out and put one in every
second mesh (net square)
• Place the net over the net hangers
• Attach the ”Omega” hooks into the
goal frame according to the drawing
• In the back the ”Omega” hooks
attach underneath
1 2 3
• Insert ”Omega”
hook into goal
frame
• Turn 90 degrees
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Malmsten Sport & Outdoor Handbücher
