Manitowoc Grove GMK 5250L Bedienungsanleitung

Operating Instructions

3 302 633 en

27.09.2017

3 302 633 en Operating Instructions GMK5250L

Important note

Any type of duplication or excerpt from

this document, even in electronic form,

is not subject to the revision service of

Manitowoc Crane Group Germany GmbH.

Manitowoc Crane Group Germany GmbH

Industriegelände West

D-26389 Wilhelmshaven, Germany

Tel: [+49] (0)44 21 294-0

Fax: +[49] (0) 44 21 294-301

The passing on or duplication of this document as well as the utilisation and disclosure of its contents is prohibited unless

expressly permitted. Infringement will incur liability for compensation. All rights pertaining to registration of patent or utility

model are reserved. The original language of this document is German.

Additional page GMK 3 302 652 en 1

31.08.2017

1Reduction of slewing speed – can be switched

on and off

In addition to the specifications in the lifting capacity table and operating

manual supplied, the automatic reduction of the slewing speed can be

switched off under certain conditions.

1.1 Important notes

These additional pages describe only this special function.

Also observe all specifications and safety instructions in the Operating

Instructions and lifting capacity table supplied.

With reduction

switched on

Depending on the degree of utilisation and the working radius, the slewing

speeds are automatically reduced to the maximum permissible levels listed

in the lifting capacity table under the comments on slewing speed.

With reduction

switched off

If the maximum slewing speeds listed in the supplied lifting capacity table are

exceeded, the buzzer tone sounds and a warning symbol is displayed.

The slewing speed is not reduced.

GRisk of accidents due to excessive slewing speed!

Observe the specified maximum permissible slewing speeds. This prevents

the truck crane from being subjected to excessive dynamic loads, which

can lead to damage to crane sections and the truck crane overturning.

Always slow down and accelerate the slewing movement slowly and avoid

swinging loads.

When reduction is switched off, you as crane operator are responsible for

a slewing speed that is suitable the current loading case.

31.08.2017

2 3 302 652 en Additional page GMK

1.2 Operation

1.2.1 Additional and modified operating elements

In the Superstructure lock menu

– Operation

–Display

Menu-independent displays

Warning messages on the RCL display

1The display switches to this position – was

previously at position (2)

2Slewing speed reduction on/off

3Reduction on – green

4Reduction off – grey

–Blue:Reduction on

–Red: Maximum permissible slewing

speed exceeded

Additional page GMK 3 302 652 en 3

31.08.2017

1.2.2 Switching reduction off and on

HThe reduction of the slewing speed is switched on with the ignition.

Switching reduction off

You can only switch off the reduction if the

slewing range type Standard has been entered.

•Select and confirm the symbol (2).

– Display symbol (1) – green.

– Warning message display (3) – blue.

The slewing speed is not reduced auto-

matically.

If the maximum permissible slewing speed

is exceeded, the buzzer tone sounds once

and the warning message (3) is displayed –

red.

HThe entered limitations for the power unit speed of the slewing gear are still

valid and the continuous speed reductions due to the working range limiter

are still active.

Switching reduction on

•Select and confirm the symbol (2).

– Symbol (1) – grey displayed.

– The warning message (3) disappears.

The slewing speed is reduced automatically.

The reduction is automatically switched on

when you enter the slewing range type

MAXbase.

31.08.2017

4 3 302 652 en Additional page GMK

Blank page

Additional pages GMK 3 302 716 en 1

08.02.2018

The display RCL (1) shows the outrigger spans

in metres (feet).

The control units (2) indicate the outrigger

spans in per cent.

The percentage values in the enclosed lifting

capacity table and the enclosed operating instruc-

tions deviate from the percentage values actu-

ally displayed on the control units (2) as they

are based on different principles.

These additional pages give an overview for different crane types of what

per cent you have to move the outrigger beams on the control units in order

to obtain the desired outrigger span.

HDepending on the operating instructions supplied, the outrigger spans are

given as the overall width or additionally as an individual width.

GMK5250L / GMK5200-1 / GMK5180-1

Length specifications Percentages

Overall widths Individual widths Control

unit

Lifting

capacity

table

7.800 m (25.6 ft) 3.900 m (12.8 ft) 100% 100%

6.854 m (22.4 ft) 3.427 m (11.2 ft) 81% 83%

5.910 m (19.4 ft) 2.955 m (9.7 ft) 63% 66%

4.310 m (14.2 ft) 2.155 m (7.1 ft) 31% 50%

2.710 m (8.8 ft) 1.355 m (4.4 ft) 0% 0%

Outrigger spans

Overview metres (feet) / per cent

08.02.2018

2 3 302 716 en Additional pages GMK

GMK5150/GMK5150L

Length specifications Percentages

Overall widths Individual widths Control

unit

Lifting

capacity

table

7.600 m (24.9 ft) 3.800 m (12.5 ft) 100% 100%

6.700 m (22.0 ft) 3.350 m (11.0 ft) 83% 83%

5.900 m (19.4 ft) 2.950 m (9.7 ft) 61% 66%

5.100 m (16.7 ft) 2.550 m (8.4 ft) 51% 50%

2.500 m (8.2 ft) 1.250 m (4.1 ft) 0% 0%

GMK4100L-1

Length specifications Percentages

Overall widths Individual widths Control

unit

Lifting

capacity

table

7.200 m (23.6 ft) 3.600 m (11.8 ft) 100% 100%

6.250 m (20.6 ft) 3.125 m (10.3 ft) 81% 80%

5.300 m (17.4 ft) 2.650 m (8.7 ft) 61% 60%

3.800 m (12.4 ft) 1.900 m (6.2 ft) 31% 40%

2.340 m (7.6 ft) 1.170 m (3.8 ft) 0% 0%

GMK3060

Length specifications Percentages

Overall widths Individual widths Control

unit

Lifting

capacity

table

6.20 m (20.3 ft) 3.10 (10.2 ft) 100%

None4.40 m (14.4 ft) 2.20 (7.2 ft) 51%

2.32 m (7.6 ft) 1.16 (3.8 ft) 0%

Additional pages GMK 3 302 808 en 1

31.08.2018

In the Operating manual supplied, it is noted that special care must be taken when

telescoping in the emergency programe (1), as no automatic monitoring takes

place.

If you move the telescoping cylinder without a telescopic section (return run),

please also note all the information in these additional pages.

(A) – These specifications apply to the outermost

telescopic section (3) – on all fixed lengths.

•Always stop extending the telescopic cylin-

der (1) once the locking point (2) on the

outermost telescopic section (3) has been

reached.

There is no automatic shutdown.

(B) – If you move too far past the locking point (2),

the cylinder tube (4) will hit the main boom

head (5) at the front.

This can lead to damage which makes telescop-

ing the main boom no longer possible.

Telescoping emergency programe

Return run of the telescoping cylinder

SRisk of damage during return run of the telescopic cylinder!

Always stop extending once the locking point on the outermost telescopic section

has been reached.

This prevents damage to the boom system through a collision between the

telescoping cylinder and the main boom head.

31.08.2018

2 3 302 808 en Additional pages GMK

Blank page

Andere Handbücher für Grove GMK 5250L

Inhaltsverzeichnis

Andere Manitowoc Baumaschinen Handbücher

Manitowoc

Manitowoc Grove GRT8100 Bedienungsanleitung

Manitowoc

Manitowoc 16000 Bedienungsanleitung

Manitowoc

Manitowoc CD15 Bedienungsanleitung

Manitowoc

Manitowoc 140.5.204 Bedienungsanleitung

Manitowoc

Manitowoc National Crane NBT40-1 Series Bedienungsanleitung

Manitowoc

Manitowoc Grove RT530E-2 Bedienungsanleitung

Manitowoc

Manitowoc Grove RT770E Bedienungsanleitung

Manitowoc

Manitowoc Grove GRT8120 Bedienungsanleitung

Manitowoc

Manitowoc MLC150-1 Bedienungsanleitung

Manitowoc

Manitowoc Grove RT9130E-2 Installations- und Benutzerhandbuch

Manitowoc

Manitowoc MLC80A-1 Bedienungsanleitung

Manitowoc

Manitowoc MLC300 Bedienungsanleitung

Manitowoc

Manitowoc MLC650 Bedienungsanleitung

Manitowoc

Manitowoc MLC650 Bedienungsanleitung

Manitowoc

Manitowoc Grove RT540E Bedienungsanleitung

Manitowoc

Manitowoc 18000 Bedienungsanleitung

Manitowoc

Manitowoc Grove RT880E Installations- und Benutzerhandbuch

Manitowoc

Manitowoc National Crane NBT50L Series Bedienungsanleitung

Manitowoc

Manitowoc Grove GMK6300L Bedienungsanleitung

Manitowoc

Manitowoc Grove GRT9165 Bedienungsanleitung

Manitowoc

Manitowoc 31000 Bedienungsanleitung

Manitowoc

Manitowoc MLC90A-1 Bedienungsanleitung

Manitowoc

Manitowoc National Crane 600E-2 Bedienungsanleitung

Manitowoc

Manitowoc 500E2 Bedienungsanleitung

Beliebte Baumaschinen Handbücher anderer Marken

SASFORKS

SASFORKS EXTREME Bedienungsanleitung

Hailo

Hailo H-50 Bedienungsanleitung

Graco

Graco LineLazer ES 1000 Gebrauchs- und Pflegehandbuch

Greenlee

Greenlee 555RSC Bedienungsanleitung

Lux Tools

Lux Tools A-FMR-20 Set Bedienungsanleitung

SIP

SIP 03683 Bedienungsanleitung

Volvo

Volvo L30G Bedienungsanleitung

Grizzly

Grizzly G8712 Bedienungsanleitung

Modulift

Modulift CMOD 12 Bedienungsanleitung

Case

Case DV201 Bedienungsanleitung

Sealey

Sealey SC10.V2 Bedienungsanleitung

Wacker Neuson

Wacker Neuson DT05 Bedienungsanleitung

HYVA

HYVA AMCO VEBA 81 Series Bedienungsanleitung

Atlas Copco

Atlas Copco Dynapac V5100TV Bedienungsanleitung

Toro

Toro 323 Bedienungsanleitung

SGS

SGS EC1500 Bedienungsanleitung

Saferoad

Saferoad VR Arcus Primus 90 Series Bedienungsanleitung

Turbosol

Turbosol BM 30 Bedienungsanleitung