marsden M-165 Bedienungsanleitung
Marsden M-165 User Manual
Please take time to read these instructions before starting to use the scale.
Page 2 of 15
Contents
Introduction 2
Product Specification 2
Safety Instructions 3
Explanation of Graphic Symbols 4
Power Supply and Low Battery 5
Operation: Basic Functions 6
Operation: Advanced Functions 8
Assembling the Column 10
Attaching the Height Measure 11
Levelling the Scale 12
EMC Guidance and Manufacturer’s Declaration 13
Error Messages 15
Manufacturer’s Declaration of Conformity 15
Introduction
Thank you for purchasing a professional gym weighing scale. Ideal for areas of heavy traffic and guaranteed accurate weight
readings. Continue reading for instructions on how to use the device and company contact information.
Product Specification
Model
M-165
Capacity/Division
250kg x 100g
Weight of Scale
Approximately 8kg
Units of Measure
Kg/St
Function Keys
ON/ZERO/OFF, UNIT, SEND, HOLD/BMI, TARE/BSA
Stabilization Time
1-2 Seconds
Operating Temperature
5 ˚C to 35˚C
Power Supply
6x 1.5V AA batteries or 12V 1A adaptor (UE24WCP1 – 120100SPA)
Indicator Display
3cm display with 5 active digits
Dimensions
Base: 310mm x 310mm x 83mm Indicator: 174mm x 107.6mm x 50mm
Warranty
4 year
Safety Instructions
Before putting the device into use, please read with care the information given in this user manual, which contains important
instructions for proper installation, use and maintenance of the device.
Marsden and/or the manufacturer shall not be liable for damages arising from failure to heed the following instructions:
•When using electrical components under increased safety requirements, always comply with appropriate regulations.
•Inappropriate installation/use will render the warranty null and void.
•Ensure the voltage marked on the power supply unit matches your mains supply.
•This device is designed for use indoors only.
•Observe the permissible ambient temperatures for use.
•The device meets the requirements for electromagnetic compatibility. Do not exceed the maximum values specified
in the applicable standards.
•Batteries should be kept away from small children. If swallowed, promptly seek urgent medical assistance.
If you have any problems with this scale, please contact Marsden/your local dealer/your service partner.
If a serious incident occurs in relation to this device, it should be reported to the manufacturer and the competent authority of
the Member State in which the user and/or patient is established.
Page 3 of 15
Cleaning
•We recommend using alcohol-based wipes or similar when cleaning the scale.
•Please do not use corrosive liquids, large amounts of water or high-pressure washers.
•Always disconnect the scale from the mains power supply before cleaning.
Maintenance
•The scale does not require any routine maintenance. However, we recommend checking the scale’s accuracy at
regular intervals. If any inaccuracies occur, please contact your local dealer or service partner.
•If you are in the UK, service contracts are available from Marsden to keep your scale accurate and reliable for longer.
Call 01709 364296 for more information.
Disposing of the Scale
•This product should not be treated as regular household waste but should be handed in to an electrical/electronic
equipment recycling centre.
•You can obtain further details from your local council, your municipal waste disposal company or from where you
purchased the product.
•Alternatively, you can return this product to Marsden –we will recycle this free of charge,
Intended Use
•This scale is intended for use to determine the weight of patients, supported by professional personnel and in rooms
intended for carrying out healthcare. The weighing value can be read after a stable weighing value has been
obtained. Before use, the scale must be checked by an authorised person to ensure it's in a suitable condition.
•Device is intended to measure one subject at a time.
Page 4 of 15
Explanation of Graphic Symbols
Caution, consult
accompanying
documents before use
Separate collection for
waste of electrical and
electronic equipment,
in accordance with
Directive 2002/96/EC
Manufacturer of medical
device
Manufacturing year of
medical device
Carefully read user
manual before
installation and usage,
and follow instructions
for use.
Medical electrical
equipment with Type B
applied part
Device catalogue
number
Authorized
representative in the
European Community
Manufacturer's batch or
lot number
Device is a medical
device
Serial number
Unique Device
Identifier
Device conforms to 93/42/EEC as amended by 2007/47/EC Medical
Device Directive. Four digit number refers to Notified Body.
Device complies with International Organization of Legal Metrology
(Class III) requirements (verified models only)
Device complies with EC directives (verified models only)
M: Conformity label in compliance with Directive 2014/31/EU for non-
automatic weighing instruments
19: Year in which conformity verification was performed and the CE
label was applied. (ex: 19=2019)
0122: Refers to Notified Body for metrology
Device complies with UK Regulation.
M: Non-Automatic Weighing Instruments Regulations 2016.
21: Year in which conformity verification was performed and the CE
label was applied. (ex: 21=2021)
0120: Refers to the Approved Body for metrology
Page 5 of 15
Power Supply & Low Battery
The indicator uses power from 6x AA batteries, or can be powered from the mains via the adaptor.
Make sure the batteries are installed in the battery box of the indicator. Alternatively, plug the adaptor (12V 1A) into the port on
the side of the scale.
Installing Batteries
Remove the battery cover.
Remove the battery case and insert batteries, ensuring they are
properly installed.
Install the battery housing.
Refit the battery cover.
Switching on the Scale
Press the ON/ZERO/OFF button firmly.
When the scale shows 0.0 on the display you are ready to
start weighing.
Page 6 of 15
Switching off the Scale
Hold the ON/ZERO/OFF button for three seconds when the
scale is turned on. The scale will power down.
Setting the Scale to Zero
If the display shows a reading other than 0.0 when nothing is
on the scale, it can be reset to zero.
Press ON/ZERO/OFF once.
The scale will return to 0.0.
Page 7 of 15
Hold Function
Press the HOLD/BMI button once, either whilst the patient is
stood on the scale or before they step onto the scale.
After a few seconds the scale will lock on the person’s weight.
When the patient leaves the scale, the weight will remain on
the display.
Press HOLD/BMI again to disable the Hold function and
return the scale to 0.0.
Note: If the weight reading remains on the display for more than five minutes, the Hold
function will automatically disable and the display will return to 0.0. If another patient steps on the scale whilst a held weight
reading is being displayed, the Hold function will be disabled.
Page 8 of 15
Body Mass Index (BMI) Function
The patient should first stand on the scale.
Hold down the HOLD/BMI button to enter BMI mode.
The scale will enter height setting mode and the
extreme left digit will flash.
Enter the height by using the TARE/BSA button to
decrease the value and HOLD/BMI button to increase
the value. To move to the next digit, press SEND.
To confirm the height hold down the ON/ZERO/OFF
button, after a few seconds the display will alternate
between weight, height and BMI.
To exit BMI mode and return to normal weighing mode,
hold down the HOLD/BMI button.
Page 9 of 15
Body Surface Area (BSA)
After calculating BMI, you can then calculate BSA. After going
through the first four steps on the previous page steps to
calculate BMI, press TARE/BSA and Body Surface Area will
be displayed.
Tare Function
Place the item/s you wish to deduct from the reading (such as
a pair of shoes) on the scale and press TARE/BSA.
Remove the item/s, and the scale will show a minus reading.
Weigh the patient as normal and the negative weight reading
will be deducted from the total weight.
Page 10 of 15
Assembling the Column (M-165 only)
Assembling the M-165’s column should ideally be carried out by two people.
Holding both the column and the base, ensuring all wiring is tucked inside the column housing, turn the scale over so that the
column can be screwed to the base from the underside of the base.
Use the four screws provided, screwing them carefully into the four holes as shown in the drawing.
Before Use
1) Place the scale on a firm and level surface
2) Unwind the levelling feet until they make contact with the ground.
3) Ensure that all four of the levelling feet and the wheels are firmly on the ground and that the spirit level bubble is
located in the center as shown below:
Correct: Incorrect:
Andere marsden Skala Handbücher
marsden
marsden MBF-6000 Bedienungsanleitung
marsden
marsden M-610 Bedienungsanleitung
marsden
marsden V-22 Bedienungsanleitung
marsden
marsden M-999 Bedienungsanleitung
marsden
marsden M-200 Bedienungsanleitung
marsden
marsden Jadever JCO Bedienungsanleitung
marsden
marsden M-600 Bedienungsanleitung
marsden
marsden VS 250E Bedienungsanleitung
marsden
marsden M-620 Bedienungsanleitung
marsden
marsden M-530 Bedienungsanleitung
marsden
marsden M-400 Bedienungsanleitung
marsden
marsden B-400 Bedienungsanleitung
marsden
marsden IP 2101 Bedienungsanleitung
marsden
marsden V-25 Bedienungsanleitung
marsden
marsden M300 Bedienungsanleitung
marsden
marsden BFA-220P Bedienungsanleitung
marsden
marsden PB-1200-I-400-APP Bedienungsanleitung
marsden
marsden M-110 Bedienungsanleitung
marsden
marsden V-180 Bedienungsanleitung
marsden
marsden M-610 Bedienungsanleitung
