Marsden M-550BT Bedienungsanleitung

USER MANUAL

M-550BT

Please take time to read these

instructions before starting

to use the scale

Version 1.1 01/18

Contents

Introduction 4

Product Specification 4

Safety Instructions 5

Explanation of Graphic Symbols 6

Power Supply and Low Battery 7

Operation 7

Setting the Bluetooth Function 8

Error Messages 9

Troubleshooting 10

EMC Guidance and Manufacturer’s Declaration 11

Recommended Separation Distance 12

Panel & LCD Display 13

Manufacturer’s Declaration of Conformity 14

Page 3

Thank you for purchasing a Marsden professional medical scale.

This is a precision Class III Weighing Instrument and considerate

use will result in many years of accurate weighing.

The scale has a maximum load capacity of 200kg which must not

be exceeded.

Product Specification

Model

M-550BT

Accuracy Class

Class III

Capacity/Division

200kg x 200g

Column

Units of Measure

Function Keys

ON/OFF, ZERO/TARE, HOLD/BMI

Stabilization Time

1-2 Seconds

Operating Temperature

5 to 35˚C

Transportation / Storage Temperature

-20 to +60˚C

Power Supply

4 x 1.5vAA size alkaline batteries

and mains adaptor 12v / 1A

Indicator Display

2.5cm LCD display with 5 active

digits

Dimensions (w x d x h)

347mm x 353mm x 60mm

Page 4

Safety Instructions

Before putting the device into use, please read with care the information given in this user

manual, which contains important instructions for proper installation, use and maintenance

of the device.

Marsden/the manufacturer shall not be liable for damages arising from failure to heed the

following instructions:

•When using electrical components under increased safety requirements, always

comply with appropriate regulations.

•Inappropriate installation/use will render the warranty null and void.

•Ensure the voltage marked on the power supply unit matches your mains supply.

•This device is designed for use indoors.

•Observe the permissible ambient temperatures for use.

•The device meets the requirements for electromagnetic capability. Do not exceed

the maximum values specified in the applicable standards.

•Batteries should be kept away from small children. If swallowed, promptly seek

medical assistance.

If you have any problems, contact Marsden/your local dealer/your service partner.

Cleaning

•We recommend using alcohol-based wipes or similar when cleaning the scale.

•Please do not use large amounts of water when cleaning the scale as this will

cause damage to the electronics. Please refrain from using corrosive liquids or high

pressure washers.

•Always disconnect the scale from the mains power supply before cleaning.

Maintenance

•The scale does not require any routine maintenance. However, we recommend

checking the scale’s accuracy at regular intervals. If any inaccuracies occur, please

contact your local dealer or service partner.

•If you are in the UK, contact Marsden on 01709 364296 about service and

calibration contracts.

Disposing of the Scale

•This product is not to be treated as regular household waste, but should be handed

in to an electrical/electronic equipment recycling centre.

•You can obtain further details from your local council, your municipal waste disposal

company or from where you purchased the product.

Page 5

Explanation of Graphic Symbols

SN-21300100

Designation of the serial number of every

device.

(Number as an example)

“Please note the accompanying

documents” or “Observe operating

instructions”

Charder Electronic Co. Ltd

No.103 Guozhong Rd, Dali Dist,

Taichung City 412, Taiwan (R.O.C)

Identification of manufacturer of medical

product including address.

Type B Applied Part

Dispose of old appliances separately

from your household waste.

This product must be disposed of at a

communal collection point.

Carefully read this operation manual

before setup and commissioning, even if

you are already familiar with Marsden

weighing scales.

Transport and storage temperature limit

indicating the upper and lower limit

(transport and storage temperature on

packaging).

Page 6

Power Supply & Low Battery

The M-550 runs on four ‘AA’ alkaline batteries.

When

is shown on the scale’s LCD display, battery power is not sufficient enough

for the scale to be used and the batteries should be replaced.

Power Supply

The four ‘AA’ size alkaline batteries are contained in a compartment inside the scale.

Access is via a removable cover on the underside of the scale, as shown below:

Installing The Battery & Connecting Your Adaptor

ON/OFF

1. Press this key to switch on the scale. The display will show 0.0kg.

2. Pressing the ON/OFF key on the opposite side of the display will reverse the scale’s

display, therefore the display can be viewed by the patient.

3. If the scale shows a figure other than 0.0kg with no weight applied, press the

ON/OFF key once to zero the display.

4. Press and hold the ON/OFF key to switch off the scale.

5. The ON/OFF key can also be used as the minus (-) key in BMI mode to reduce the

height reading.

HOLD

1. Press the HOLD/BMI key to enter into enable the Hold feature.

2. The arrow pointing at the hold symbol will start to flash and the LCD display will

Page 7

show .

3. The person being weighed can now stand on the scale. Their weight reading will

hold and remain on the display.

4. To return the display back to zero, the HOLD/BMI button can either be pressed or

the individual being weighed can step off the scale.

TARE

1. The ZERO/TARE key can be used to remove any unwanted weight from the scale’s

display. For example, you may want to remove the weight of someone’s shoes

from the reading, to leave only the person’s weight showing. To do this, place the

shoes on the scale and press the ZERO/TARE key once.

The weight of the shoes will then be zeroed off.

2. Weigh the individual as normal.

3. Remove the shoes and press ZERO/TARE again to cancel the Tare value and

return the scale to zero.

BMI

1. After the patient stands on the scale, press and hold the HOLD/BMI key for three

seconds. The scale will enter BMI mode.

2. The display will show the last inputted height.

3. Press the HOLD/BMI button to decrease the height and ZERO/TARE to increase

the height.

4. When the correct height is showing on the display, press the ON/OFF button.

5. BMI will automatically be calculated and the display will show weight and BMI in

rotation.

6. Press ON/OFF to disable the BMI function.

Setting the Bluetooth Function

Please note: Marsden does not supply software for receiving data from the scale. These

instructions should be followed when you are connecting to a system or device configured

to work with Marsden Bluetooth scales.

1. Press and hold ZERO/TARE for three seconds. The display will show ‘SETUP’.

2. Press and hold HOLD/BMI until the display shows ‘BLUET’.

3. Press ZERO/TARE to enter Bluetooth setting mode.

4. Press HOLD/BMI to toggle between ‘on’ (enabled) and ‘off’ (disabled).

5. Press ZERO/TARE to confirm.

6. Press HOLD/BMI twice, and then ZERO/TARE once to return to normal weighing

mode.

Page 8

Error Messages

Low Battery

The scale’s alkaline AA type batteries are

flat; please replace the batteries.

Overload

This indicates that the scale’s load sensor(s)

have been overloaded. Reduce the loading

and retry.

Counting Error

1. The signal from the load cells is too

high. Please remove any weight from

the scale and try to power on again. If

the scale continues to show the error

message, it indicates a fault with the

electronics or wiring.

2. The signal from the load cells is too

low. Please remove any weight from

the scale and try again. If the scale

continues to show the error message,

it indicates a fault with the electronics

or wiring.

High/Low Zero Count

1. The scale is above its zero range.

Please remove any weight from the

scale and power on again. If the

scale continues to show the error

message, it indicates a fault with the

electronics.

2. The scale is below its zero range.

Check there is nothing jammed

underneath the scale and power on

again. If the scale continues to show

the error message, it indicates a fault

with the electronics.

EEPROM Error

This indicates there is a fault with the scale’s

software and is normally caused by a fault

with the load cell or wiring. Contact your

local service representative.

Page 9

Troubleshooting

The original purchaser can enjoy the benefits under the effective warranty against

functional defects in material and workmanship, subject to the terms and conditions listed

in the Warranty and Return Policy.

If the scale fault is due to mechanical or electronic defect then the scale will be repaired or

replaced under warranty. The purchaser will need to return the scale to the original place of

purchase (Marsden/your Authorised Dealer).

Before you contact your Authorised Dealer, please read through the following section

carefully.

Self-checking tips

Some functional defects can be identified and maintained by users as listed below:

1) Power Failure

•Check if the mains power adaptor has been correctly plugged into the scale.

•Check if the battery power is running low. Replace with new batteries if

required.

2) Indicator showing “000” ZERO SPAN out of range

•Incorrect weighing result. Has the scale been dropped, or suffered impact? Is

the scale damaged?

•Proper re-calibration procedure required to correct the weighing accuracy.

•Interference due to RF disturbance, ground vibration, etc.

•Unstable platform feet. These can be adjusted by turning; check the spirit

level.

•The weighing scale is not on solid, level ground.

Page 10

Inhaltsverzeichnis

Andere marsden Skala Handbücher

marsden

marsden V-23 Bedienungsanleitung

marsden

marsden BFA-220P Bedienungsanleitung

marsden

marsden MPPS-250 Bedienungsanleitung

marsden

marsden M-920 Bedienungsanleitung

marsden

marsden M-650 Bedienungsanleitung

marsden

marsden MPPS-250 Bedienungsanleitung

marsden

marsden M-165 Bedienungsanleitung

marsden

marsden MBF-6000 Bedienungsanleitung

marsden

marsden IP 2101 Bedienungsanleitung

marsden

marsden V-24 Bedienungsanleitung

marsden

marsden MBF-6000 Bedienungsanleitung

marsden

marsden BAS-200 Bedienungsanleitung

marsden

marsden M-400 Bedienungsanleitung

marsden

marsden C-100 Bedienungsanleitung

marsden

marsden M-930 Bedienungsanleitung

marsden

marsden M-545 Bedienungsanleitung

marsden

marsden PB-1200-I-400-APP Bedienungsanleitung

marsden

marsden Jadever JCO Bedienungsanleitung

marsden

marsden M-620 Bedienungsanleitung

marsden

marsden MBF-6010 Bedienungsanleitung

marsden

marsden BS-250BT Bedienungsanleitung

marsden

marsden M300 Bedienungsanleitung

marsden

marsden Boxer MPS 30 Bedienungsanleitung

marsden

marsden I-400SS Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung

marsden M-550BT Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken