Marshall Electronics V-R185-DLW Bedienungsanleitung

Marshall Electronics

, Inc.

1910 East Maple Ave.

El Segundo, CA 90245

Tel: (800) 800-6608 / (310) 333-0606 • Fax: 310-333-0688

www.LCDRacks.com •sales@lcdracks.com

Marshall Electronics

Model No. V-R185-DLW

18.5” DLW Desktop and Rack Mount Dual Link / Waveform Monitor

Operating Instructions

Edition 1 Revision 7W

235

Maintenance

■Screen Cleaning

Periodically clean the screen surface using ammonia-free cleaning wipes (Marshall Part No. V-HWP-K). A clean micro-fiber cloth

can also be used using only non-abrasive and ammonia-free cleaning agents. Do not use paper towels. Paper towel fibers are

coarse and may scratch the surface of the polycarbonate faceplate or leave streaks on the surface. Antistatic and fingerprint

resistant cleaning agents are recommended. Do not apply excessive pressure to the screen to avoid damaging the LCD.

■Faceplate Dusting

Dust the unit with a soft, damp cloth or chamois. Dry or abrasive cloths may cause electrostatic charge on the surface, attracting

dust particles. Neutralize static electricity effects by using the recommended cleaning and polishing practice.

Warranty

Marshall Electronics warranties to the first consumer that this V-R185-DLW LCD monitor will, under normal use, be free from

defects in workmanship and materials, when received in its original container, for a period of one year from the purchase date.

This warranty is extended to the first consumer only, and proof of purchase is necessary to honor the warranty. If there is no

proof of purchase provided with a warranty claim, Marshall Electronics reserves the right not to honor the warranty set forth

above. Therefore, labor and parts may be charged to the consumer. This warranty does not apply to the product exterior or

cosmetics. Misuse, abnormal handling, alterations or modifications in design or construction void this warranty. It is considered

normal for a minimal amount of pixels, not to exceed three, to fail on the periphery of the display active viewing area. Marshall

Electronics reserves the option to refuse service for display pixel failure if deemed unobtrusive to effective use of the monitor by

our technicians. No sales personnel of the seller or any other person is authorized to make any warranties other than those

described above, or to extend the duration of any warranties on behalf of Marshall Electronics, beyond the time period

described above. Due to constant effort to improve products and product features, specifications may change without notice.

34 3

Table of Contents

Installation and Initial Setup ------------------------------------------------------------------------------------------------------5

Top and Front Panel Features ----------------------------------------------------------------------------------------------------7

Rear Panel Features-----------------------------------------------------------------------------------------------------------------8

Compatible Input Formats---------------------------------------------------------------------------------------------------------9

MAIN MENU AND NAVIGATION------------------------------------------------------------------------------------------------ 10

Using the RotoMenu knob ------------------------------------------------------------------------------------------------------ 10

Marker Setup Submenu ......................................................................................................................................................................10

Video Config Submenu ........................................................................................................................................................................12

Color Config Submenu.........................................................................................................................................................................16

System Config Submenu......................................................................................................................................................................16

OSD Config Submenu ..........................................................................................................................................................................18

IMD Config Submenu ..........................................................................................................................................................................21

IMD Fixed Config Submenu ................................................................................................................................................................. 23

Closed Captioning Submenu ...............................................................................................................................................................24

Wave/Vector Submenu ....................................................................................................................................................................... 25

Ancillary Submenu...............................................................................................................................................................................27

Service Submenu .................................................................................................................................................................................28

Specifications----------------------------------------------------------------------------------------------------------------------- 30

Dimensions-------------------------------------------------------------------------------------------------------------------------- 31

Maintenance------------------------------------------------------------------------------------------------------------------------ 35

Warranty ---------------------------------------------------------------------------------------------------------------------------- 35

433

32 5

Installation and Initial Setup

■Unpacking

Carefully unpack the V-R185-DLW monitor and verify that the following items are included:

• V-R185-DLW Monitor

• V-PS24-6.25-XLR-R/A Power Supply

• Operating Instructions

Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage, immediately

contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States, call +1 (310) 333-

0606.

■Installation

The V-R185-DLW can be mounted in any standard EIA 19” equipment rack. The attached rack ears can be angled to provide the

user control over the viewing angle. Adequate ventilation is required when installed to prevent possible damage to the

monitor’s internal components. Please see the Dimensions section for more information.

A VESA standard 75mm hole pattern also allows custom mounting installations. Alternately, the V-R185-DLW can be used in a

desktop configuration with optional stand. Please contact Marshall Electronics for more information.

■Connections, Power-On and Initial Setup

Plug the power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the Power connector to the back of the monitor.

Connect the required cables for video signal input and output. (Power must be applied to the V-R185-DLW for the active loop-

though output to be activated.) The monitor defaults to ‘ON’ when power is supplied. Video will automatically be detected and

displayed on the screen.

631

Dimensions

Specifications

■PANEL

Screen Size 18.5” Diagonal

Display Area (h x v) 409.8 x 230.4 mm

Pixels 1366 x RGB x 768

Viewing Angle (h x v) 178° x 178°

Brightness 300 cd/m2

Contrast Ratio 1000:1

Pixel Pitch (h x v) 0.100 x 0.300 mm

■CONNECTORS

Video Input

3G-SDI 2 x BNC Female (75 Ω)

Video Output (Active Loop-Through)

3G-SDI 2 x BNC Female (75 Ω)

DVI Input

DVI-I 1 x DVI-I Female Connector

Power Input

4-Pin XLR Connector

Tally / GPI Hardware Interface

HD-15 Female

RS-422/485 Interface

2 x RJ12 (Modular 6P6C)

■TALLY Hardware Interface (HD-15)

Activation requires contact closure of pin to ground

on the HD-15 connector:

■ELECTRICAL

Power Consumption 2.0A @ 24VDC (48 W)

Voltage Requirement 24 VDC

Pinout

Pin 1: -

Pin 2: N/C

Pin 3: N/C

Pin 4: +

■MECHANICAL

Weight (with rack ears): 8.60 lbs

Operating Temperature 32°F to 104°F (0°C to 40°C)

Storage Temperature -4°F to120°F (-20°C to

50°C)

See Dimensions section for exact specifications.

.Protocols: Image Video, TSL v4.0, MEI

Top and Front Panel Features

Power Button

Use the power button to toggle between ON and STANDBY

modes. The LED on the POWER button will illuminate fully

when the unit is in STANDBY mode. The LED will dim when

the unit is ON.

Input Select Buttons (SDI 1, SDI 2, DVI)

Use the SDI 1, SDI2 and DVI buttons to select the

corresponding video input. Accepted video standards are

automatically detected.

User-Definable Function Buttons

Four user-definable function buttons can be used for direct

access to various settings. Functions are assigned using the on-

screen menu.

Layout Button

Use the Layout button to switch between the four available

layouts on the monitor. See the Layouts section for more

information the available l ayouts.

RotoMenu™Knob

The RotoMenu™knob allows for accessing and navigating the

main menu using only a single knob.

Image Adjustment Knobs

Use the image adjustment knobs to adjust color brightness,

color-saturation, tint, and contrast of the image. The status of

each image adjustment parameter is shown on the bottom left

of the screen, with values ranging from 0 to 100. Default value

is 50.

LED Tally

Three LED tally lights (yellow, red, green) are available above

the screen.

Rear Panel Features

SDI Inputs / Outputs and DVI-I Input

The V-R185-DLW has two 3G-SDI inputs and two active loop-

through outputs. SDI 1 and SDI 2 can be used simultaneously

to display Dual Link SDI signals. The DVI-I Input Connector

includes EDID and HDCP for connection to computers, DVD

Players, Rasterizers, etc.

Power Input

Connect the 4-pin XLR power input connector here. Power

should only be supplied from the included power supply.

IMPORTANT: If using a power source other than the included

power supply, damage may result. Please use the pin out

diagram in the Specifications section.

Tally Input / GPI Connector

The LED tally can be activated via the HD-15 connector by

connecting the corresponding pin to ground. A variety of

external devices can be used to perform the contact closure.

The HD-15 connector can also be used as a GPI port by

changing the settings in the On Screen Menu. No additional

power should be supplied to the HD-15 port.

RS-422/RS-485 Serial Interface

The RS-422/485 ports are used to remotely control the IMD or

all DLW features. (Note: Connector/pin-out may need to be

adapted depending on the protocol and controlling device

used). Only one connection to either port is needed to control

the monitor. The second port can be used to loop multiple

monitors in the same bus.

VESA Hole Pattern

VESA-standard 75mm hole-patters are provided to accomdate

a variety of custom mounting options.

■DID/SDID

Use this section to select which packet IDs should be counted on the DLW monitor display. For example, 0x6060 would count

the Timecode data packets, 0x6101 would count the EIA-708 CC data packets and 0x6102 would count the EIA-608 CC data

packets. Any ancillary packet ID can be chosen, from 0000 to FFFF.

Service Submenu

■Software Version Display

The Main Board, Keypad, and FPGA software version numbers are displayed.

The following information is displayed:

• rel: Release Package version number

• ipa Input processor firmware

• dlw FPGA Version

• ipap Product Type

• kp Keypad version number

Service Menu

Compatible Input Formats

The following video standards are supported by the V-R185-DLW:

SDI Inputs

525i, 625i/50

720p/29.97, 30, 50, 59.94, 60

1080p/23.98, 23.98sF, 24, 24sF, 25, 29.97, 30

1035i/59.94, 60

1080i/ 50, 59.94, 60

3G – Level A and Level B

YCbCr, YCbCr+A, RGB, RGB+A

1080p/ 60, 59.94, 50

1080p/ 30, 29.97, 25, 24, 23.98, 30sF, 29.97sF, 25sF, 24sF, 23.98sF

1080i/ 60, 59.94, 50

3G – Level A and Level B

YCbCr, YCbCr+A, RGB, RGB+A

1080p/ 60, 59.94, 50

1080p/ 30, 29.97, 25, 24, 23.98, 30sF, 29.97sF, 25sF, 24sF, 23.98sF

1080i/ 60, 59.94, 50

Dual Link

YCbCr, YCbCr+A, RGB, RGB+A

1080p/ 60, 59.94, 50

1080i/ 60, 59.94, 50

1080p/30, 29.97, 25, 24, 23.98, 30sF, 29.97sF, 24sF, 23.98sF

1080p/ 30, 29.97, 25, 24, 23.98

DVI-I Input (DVI-Analog and DVI-Digital)

640 x 480/ 60

800 x 600/ 60

1024 x 768/ 60

1280 x 1024/ 60

1600 x 1200/ 60

Video standards (HDMI or YPbPr over DVI connector)

720p/50, 59.94, 60

1080i/50, 59.94, 60

1080p/23.98, 24, 25, 29.97, 30, 50, 59.94, 60

MAIN MENU AND NAVIGATION

Access and navigate the main menu using the RotoMenu™knob:

Using the RotoMenu knob

• Press the RotoMenu™knob to enter the main menu.

• Rotate the knob to scroll up or down in the main menu or each submenu.

• Press the RotoMenu™knob to enter a submenu or choose a setting.

• To return to main menu from submenu, select ‘Back’ and press the RotoMenu™.

The menu timeout can be set in the OSD Timeout section of the OSD Config submenu.

Marker Setup Submenu

Use the Marker Setup submenu to select various on-screen markers, adjust the Marker Background, or toggle the Center Marker

ON or OFF.

Main Menu

Marker Setup Submenu

■Limits

Use the Limits option to differentiate data (indicated by a red highlight) on the Waveform display that goes above a Limit Max

(maximum) and goes below a Limit Min (minimum) set in the Wave/Vector submenu. The Limit maximum and minimum can

be set from 0000 to 1023. Note: Setting the Limits option to ON will override the Colorize Waveform option. All Waveform

display data within the limits will appear in white.

■Limit Max

Use this to set the desired maximum for the Limit display of the waveform monitor. Any Waveform data that goes beyond

this Limit Max will be displayed in red.

■Limit Min

Use this to set the desired minimum for the Limit display of the waveform monitor. Any Waveform data that goes below this

Limit Max will be displayed in red.

■Vectorscope Targets

Use the Vectorscope Targets option to set your Vectorscope targets up for 75% or 100% color bar signals. You can also set

your Vectorscope Targets to the OFF position.

■Overlay Position

Use the Overlay Position option to place the Waveform, Vectorscope and Audio Level display on the Top or Bottom of the

screen while in the DLW Overlay display mode. You can also set your Overlay display to OFF.

■Overlay Transparency

Use the Overlay Transparency option to set the transparency of the Waveform, Vectorscope and Audio Level display while in

DLW Overlay mode. Choose a value from 000-100. A low value will cause the Waveform, Vectorscope and Audio Level data

to blend into the background, while a high value will make the data appear more visible against the video display in the

background.

Ancillary Submenu

Use the Ancillary submenu to determine which ancillary packet IDs should be counted in the Ancillary Status portion of the

DLW monitor display.

Inhaltsverzeichnis

Andere Marshall Electronics Monitor Handbücher

Marshall Electronics

Marshall Electronics AR-DM2-B Bedienungsanleitung

Marshall Electronics

Marshall Electronics QVW-2710 Bedienungsanleitung

Marshall Electronics

Marshall Electronics QV261A-HDSDI Bedienungsanleitung

Marshall Electronics

Marshall Electronics 3D-241-HDSDI Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-R82DP-HD Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-LCD50-HDMI Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-LCD90MD Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-R102DP-2SDI Bedienungsanleitung

Marshall Electronics

Marshall Electronics M-LYNX-10W Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-R84DP-HDSDI Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-R842DP-AFHD Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-R231-IMD-HDSDI Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-LCD70XP-HDMI Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-LCD70-AFHD Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-R901DP-AFHD Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-R82DP-2C Bedienungsanleitung

Marshall Electronics

Marshall Electronics ORCHID OR-841-HDSDI Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-LCD84SB-AFHD Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-R102DP-HD Bedienungsanleitung

Marshall Electronics

Marshall Electronics M-LYNX-702W Bedienungsanleitung

Marshall Electronics

Marshall Electronics V-LCD70MD Bedienungsanleitung

Marshall Electronics

Marshall Electronics Orchid OR-2410 Bedienungsanleitung

Marshall Electronics

Marshall Electronics QVW-1708-3G Bedienungsanleitung

Marshall Electronics

Marshall Electronics AR-AM4 Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung