Martec Newport Series Bedienungsanleitung
www.martecaustralia.com.au
NEWPORT Series Installation Guide
Thanks for choosing our Newport Series ceiling fan.
We strongly recommend that you read this manual carefully before installation.
Models Parameters (Fan Only):-
MNF143WWR 1420mm 3 Blade Ceiling Fan White with Remote Control
MNF143MMR 1420mm 3 Blade Ceiling Fan Matt Black with Remote Control
MNF143OWR 1420mm 3 Blade Ceiling Fan Walnut with remote control
Models Parameters (Fan and Light):-
MMF1433WWR 1420mm 3 Blade Ceiling Fan White, 18W Tricolour LED Light with Remote Control
MMF1433MMR 1420mm 3 Blade Ceiling Fan Matt Black, 18W Tricolour LED Light with Remote Control
MMF1433OWR 1420mm 3 Blade Ceiling Fan Walnut, 18W Tricolour LED Light with Remote Control
Part List:
Qty 1x motor assembly Qty 1x instruction manual Qty 1x screw kit
Qty 1x balancing kit Qty 1x hanging bracket Qty 1x remote control kit
Qty 3x blades
Application
Flat Surface / Ceiling Slope Ceiling up to 15° Corrugated Ceiling Apex Ceiling
How to Assemble
Secure the hanger bracket
to ceiling beam or a suitable
piece of timber inserted
between the ceiling beams
using the two long screws
supplied with the package.
(See Fg.1)
Place circular shockproof
gasket above the hanger
bracket. Align the bracket
and screw the hanger
bracket to the ceiling tightly.
(See Fg.2)
Place fan into hanger
bracket and align Ball Joint
Slot with hanger bracket as
illustrated.(See Fg.3)
After wiring is completed,
attach the canopy to the
hanger bracket by pushing
upwards and twisting anti-
clockwise. Tighten screws
and ensure canopy is not
touching the ball joint.
(See Fg.4)
Fg.1 Fg.2 Fg.3 Fg.4
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
How to Install Blades
Attach the blade to the top of the motor using the 4 blade
screws provided. Tighten the screws and repeat this
procedure for all blades. (See Fg. 6)
Fg.6
To install align the blades with the orice as shown. (See
Fg. 5)
Fg.5
How to Install / Remove the Glass Shade
To install - place the glass shade and spin it clockwise.
To remove - turn the glass shade anti-clockwise.
(See Fg.7)
Fg.7
CCT (Colour Changeable Temperature)
Choose colour temperature by icking the switch in the
LED (See Fg.8)
C = 3000K cool white
N = 4000K neutral white
W = 5000K warm white
Fg.8
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
Instructions and Functions of Transmitter
1. LED indicator light
2. Light ON/OFF
(Use to dim light within 1s)
3. Speed of the fan
(1 high speed - 5 low speed)
4. Timing control of the fan
5. Direction of the fan (reverse
switch)
6. Fan ON/OFF
7. 12v battery to be used
in transmitter
NB: Remote shown fan only NB: Remote shown fan and light
1. LED indicator light
2. Speed of the fan
(1 high speed - 5 low speed)
3. Timing control of the fan
4. Direction of the fan (reverse
switch)
5. Fan ON/OFF
6. 12v battery to be used in
transmitter
Installing Receiver Remote Control
Important Reminders
• Receiver must be correctly installed in the mounting bracket
• When the transmitter cannot control the receiver, please check
i) has sucient battery in the transmitter
ii) any existence of similar remote controlled products nearby that cause interference
• Replace battery if getting low as this will aect sensitivity of the transmitter
• Take the battery out from the transmitter when leaving used for a long time to avoid battery leaks
• Support up to 200W lighting power
• Isolation switch MUST be connected in the line
• Dimming switch on the light models is operated by tuning the light ON/OFF button within 1s. Light output will dim
in stages from 24W to 9W to 3W approximately
NB: Receiver shown fan and lightNB: Receiver shown fan only
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
Wire Connections
NB: Remote Control fan and light
240V Supply
1
1
2
2P Plug
4P Plug
2
To the
Fan Light
To AC
Power
NB: Remote Control fan only
1
1
WARNING
• Installation of fans MUST follow SAA standards and meet local authority regulations.
• Installation MUST be carried out by a qualied and licensed electrician.
• Fan and light MUST be earthed.
• Bracket MUST be rmly attached to a at solid structure or timber frame.
• DO NOT mix blades from one model to another, all blades MUST be replaced if damaged.
• The warranty is VOID if product is not installed according to this installation guide.
6* Year Warranty
Visit our website for details https://www.martecaustralia.com.au/warranty-statement/
240V Supply
4P Plug
2
To the Fan Motor
2
1
1
To the Fan Motor
2P Plug
To AC
Power
Dieses Handbuch passt für folgende Modelle
6
Andere Martec Lüfter Handbücher
Martec
Martec NEWPORT Series Bedienungsanleitung
Martec
Martec MMDC133WOR Bedienungsanleitung
Martec
Martec VIPER DC Series Bedienungsanleitung
Martec
Martec Flush Bedienungsanleitung
Martec
Martec Elite AC Series Bedienungsanleitung
Martec
Martec Ariel Series Bedienungsanleitung
Martec
Martec Governer Series Bedienungsanleitung
Martec
Martec Liberty Series Bedienungsanleitung
Martec
Martec Norfolk Aero DC Smart Series Bedienungsanleitung
Martec
Martec Kingston MKDC124OB Bedienungsanleitung
Martec
Martec Lifestyle series Bedienungsanleitung
Martec
Martec Flush AC Series Bedienungsanleitung
Martec
Martec Malibu Series Bedienungsanleitung
Martec
Martec SATURN MXFSS20W Bedienungsanleitung
Martec
Martec Cruise Series Bedienungsanleitung
Martec
Martec Beret Series Leitfaden
Martec
Martec Avoca DC Series Bedienungsanleitung
Martec
Martec METRO DC Series Bedienungsanleitung
Martec
Martec AVOCA DC Series Bedienungsanleitung
Martec
Martec Wave MWF133TSR Bedienungsanleitung
