Martin Yale Count AccuCreaser Bedienungsanleitung

Serial Number ___________________________

Date ___________________________________

ACCUCREASER TOUCH

Page left blank intentionally

TABLE OF CONTENTS

INTRODUCTION .......................................................................................................... 5

ELECTRICAL REQUIREMENTS AND SPECIFICATIONS ....................................................... 5

SAFETY PROCEDURES/CARE & MAINTENANCE .............................................................. 6

COMPONENT IDENTIFICATION .................................................................................... 7

SETTING UP ACCUCREASER.......................................................................................... 8

PAPER STOP ASSEMBLY ............................................................................................ 9

PERF MODE ............................................................................................................ 12

FEEDER MODE ........................................................................................................ 13

CREASE MODE ........................................................................................................ 13

PROGRAMMING FOR CREASE MODE ............................................................................ 15

HALF FOLD .............................................................................................................. 15

TRI-FOLD................................................................................................................. 15

Z FOLD .................................................................................................................... 15

LETTER FOLD ........................................................................................................... 15

ROLL FOLD .............................................................................................................. 15

GATE FOLD .............................................................................................................. 16

DOUBLE GATE.......................................................................................................... 16

DOUBLE PARALLEL ................................................................................................... 16

PERFECT BIND SINGLE HINGE ................................................................................... 17

CUSTOM CREASE SETUPS .......................................................................................... 17

SAVING/RECALLING CUSTOM JOBS ............................................................................ 18

PERFECT BIND DOUBLE HINGE ................................................................................. 16

PERFECT BIND NO HINGE ......................................................................................... 17

TRANSPORT AND VACUUM OPERATION CONTROLS...................................................... 14

DELIVERY TRAY ASSEMBLY....................................................................................... 8

MACHINE CONTROLS................................................................................................... 10

PUMP CONTROLS.........................................................................................................10

TOUCH SCREEN CONTROLLER......................................................................................11

SETTING THE AUTOMATIC FEEDER............................................................................. 20

HEIGHT ADJUSTMENT CALIPER .................................................................................. 20

LOADING THE FEEDER ............................................................................................... 21

CHECKING THE SENSOR ................................................................................................ 22

PERF SHAFT & STRIKE PLATE ......................................................................................22

REMOVING THE PERF SHAFT TO CHANGE CONFIGURATIONS .......................................23

PERFORATING AND SETTING PERF BLADE .................................................................24-25

FOLDING DIRECTION OF PAPER ................................................................................. 27

CHANGING LOWER CREASE DIE .................................................................................. 27

TROUBLESHOOTING ...................................................................................................... 28

ADJUSTING RAC ROLLERS

(DEPTH OF CREASE)

..........................................................27

MICRO ADJUSTING THE CREASE POSITION ................................................................ 18

BATCH COUNTER.........................................................................................................19

SCORING AND SETTING SCORE BLADE ...........................................................................26

ACCUCREASER…………………………………………….350 lbs

………………………………………………………………….32”Lx27”Wx26”D

………………………………………………………………….48”Lx48”Wx52”H

………………………………………………………………….5”x5-7/8”

.……………………………………………………….………..18”x20”

Net Weight:

Overall Dimensions:

Boxed Dimensions:

Min. Sheet Size:

Max. Sheet Size:

Power Requirement:

Circuit Protection:

110v, 60 HZ, AC, or International 230v, 50/60HZ, AC

20 amp line required for models with pump

3 AMP Circuit Breaker, 3 AMP Fuse

NOTE: The AccuCreaser is capable of handling many types of applications above and

beyond the standard specifications. It is possible to feed quite a variety of jobs, from

30” sheets to die cut stocks. However, the performance of the AccuCreaser on these

special applications is directly related to the experience of the operator.

MODE 8.5 X 11 Sheet (est)

12,000Perf Mode:

Crease

Mode:

5,500

OPERATING SPEEDS

SPECIFICATIONS

ELECTRICAL REQUIREMENTS AND SPECIFICATIONS

•Read through the owner’s manual. Follow instructions CAREFULLY.

•NEVER use a wet area. Electric shock could occur.

•Use a GROUNDED outlet and a GROUNDED circuit. Do no use

ungrounded equipment on the same circuit.

•Always use a dedicated line. DO NOT use with line splitting surge

protector.

•Keep fingers and hands away from creasing bar, perf blades, and rubber

rollers.

•Keep cords clear of moving parts.

•Turn off machine at the top panel, then unplug the main power cord.

This will prevent damage to your machine by power/voltage spikes.

•To unplug cords, always grasp the plug body, never pull on cords to

disconnect. Wire fatigue and possible shock could result from improper

disconnect procedures.

BE ALERT! BE CAREFUL!

CARE AND MAINTENANCE

The ACCUCREASER is a precision machine. It is very important to keep it free of

excessive dust, dirt and foreign matter. We recommend that you keep the machine

covered when not in use.

BEARINGS/BUSHINGS:

The bearings are sealed roller bearings and are designed to

be self lubricating, however dirt and dust can get into them causing clogging and dirt

build up. It is recommended to oil them daily under heavy use or monthly under light

use. The Bushings are Bronze and require lubrication more frequently. Oil these once

a week under heavy use.

STRIKE DIE:

The groove in the lower die should be cleaned periodically using a

toothbrush to remove any dirt or build up.

SENSOR EYE:

Clean the lower reflector tape located on the plate under the strike

plate of the machine. Dust will cause the beam to not reflect correctly. Clean when

necessary.

REMOVEABLE SCREWS:

When these show signs of wear or stripping, replace as

soon as possible. If these strip or hollow out they can be costly to remove. If you do

keep your AccuCreaser clean and in top condition, it will give you years of service.

SAFETY PROCEDURES

BEFORE USE:

DURING USE:

AFTER USE:

Crease Bar

Delivery Tray

Perf and Score Assemblies

Power Switch

Pump with

Vacuum Valve

Pg. 11

Pg. 8

Pg. 10

Pg. 24-26

Touch Screen

Delivery Tray

Pump with Vacuum

Valve Perf and Score

REFERENCES

COMPONENT IDENTIFICATION

Touch Screen

Paper Stop

Install on top of the first

dowel pin and under the

second.

Tuck Lip up as shown

SETTING UP YOUR ACCUCREASER

This machine is 99% ready to go when it arrives on your dock. There are only a few

items that need to be put into position before it is ready to use. Those 2 items are

below:

DELIVERY TRAY ASSEMBLY

INSTALLING THE DELIVERY TRAY

Position the tray to slide it under the dowel pins and rest it on the lower dowel pins.

Upper Position shown below

Now that the Machine is setup, let's learn how to use the machine. The

sections below will guide you through the operation of the machine.

PAPER STOP ASSEMBLIES

INSTALLING THE PAPER STOPS

1. Inside the box should be 3 paper stops (2 will have a bend & 1 will be straight).

2. Place the straight paper stop in place. This is the back paper stop. (See Diagram)

3. Place the 2 paper stops in position as show below.

The paper stops hold their position using knobs making it easier for adjustment. The

positions of the paper stops will depend on the individual job.

*HWWLQJWKHSRVLWLRQFRUUHFWLVLPSHUDWLYHWRVPRRWKRSHUDWLRQRIWKHPDFKLQH

If the paper stops are set too close the paper will hit them as it exits the machine

resulting in a paper jam. However, if the paper stops are set too loose the paper will

stack in an unorganized manner.

There is one switch on the Accucreaser the main power. Everything else is controlled

by the Touch Screen.

MAIN POWER

On the operator side cover at the top on the right side is the main power button . This

is the on and off power for the machine. When pressed it will illuminate. This is how

you know the machine is on. Do not leave the machine on when not in use.

The pump is controlled by the touch screen. Pressing the run button the pump is

powered on. Use the knobs on the pump (pictured below right) to control the output

of the pressure and vacuum. As illustrated on the knobs you can control the suction

and the blow affecting the stock. Use care to not remove the pump knobs completely

as they have a directional specific spring for each knob. Depending on the stock you

are using you will adjust these knobs to ensure proper feeding. The suction can be

adjusted as well as the vacuum pickup point to ensure enough suction to pull the

bottom sheet. The pressure will “fluff” the stack along the rails and make it easier to

pull the bottom sheet as well.

MACHINE CONTROLS

PUMP CONTROLS

Inhaltsverzeichnis

Andere Martin Yale Bindemaschine Handbücher

Martin Yale

Martin Yale PaperMonster WB6 Bedienungsanleitung

Beliebte Bindemaschine Handbücher anderer Marken

GBC

GBC CombBind C800pro Bedienungsanleitung

JBI

JBI Alpha-Doc MKIII Bedienungsanleitung

GBC

GBC CombBind A20 Bedienungsanleitung

GBC

GBC DocuBind P100 Bedienungsanleitung

Peach

Peach PB300-20 Bedienungsanleitung

Morgana

Morgana DigiBook 450 Bedienungsanleitung

Rexel

Rexel CB345E Bauanleitung

GBC

GBC AP-2 Bedienungsanleitung

Opus

Opus MB 300 Bedienungsanleitung

Duplo

Duplo DC-645 Bedienungsanleitung

Akiles

Akiles AlphaBind Kurzanleitung

ibico

ibico Thermal Binder 260 Bedienungsanleitung

Rollabind

Rollabind PBS 2000 Bedienungsanleitung

SYSFORM

SYSFORM CP340H Bedienungsanleitung

GBC

GBC THERMALBINDER400T Bedienungsanleitung

GBC

GBC CombBind C20 Bedienungsanleitung

Renz

Renz RENZ DTP 340A Betriebsanleitung

Ricoh

Ricoh RB5020 Bedienungsanleitung