Martin Atomic 3000 LED Bedienungsanleitung

Atomic 3000 LED

SERVICE MANUAL

Revision A, 11-30-2017

Service manual

2 of 20Atomic 3000 LED - Revision A, 11-30-2017

Table of contents

General information ............................................................................................................................................ ...3

Safety instructions .................................................................................................................................................................................3

Tools ........................................................................................................................................................................................................3

Spare parts ..............................................................................................................................................................................................4

Troubleshooting .................................................................................................................................................. ...5

Overview of error codes.........................................................................................................................................................................5

Wiring diagram........................................................................................................................................................................................6

Repair and replacement...................................................................................................................................... ...7

Replacing the front glass.......................................................................................................................................................................7

Replacing the back light reector assembly........................................................................................................................................7

Replacing the back light LED pixel board ............................................................................................................................................8

Replacing the main light engine assembly ..........................................................................................................................................9

Replacing the PSU................................................................................................................................................................................10

Replacing the main PCB/UI.................................................................................................................................................................. 11

Replacing the air lters ........................................................................................................................................................................13

Replacing the fans................................................................................................................................................................................13

Replacing the handle............................................................................................................................................................................14

Calibrating the PSU ..............................................................................................................................................................................15

Maintenance....................................................................................................................................................... ...18

Cleaning the product............................................................................................................................................................................18

Conditions .............................................................................................................................................................................................18

Maintenance schedule .........................................................................................................................................................................19

Service manual

3 of 20Atomic 3000 LED - Revision A, 11-30-2017

Figure 1: Safety instructions

Figure 2: Tools

Figure 3: ESD mat and wristband

General information

This service manual contains information about how to

service Atomic 3000 LED.

Safety instructions

Before you carry out service work, read this document.

Installation and service work must comply with local

regulations and accepted codes of good practice.

Observe the safety instructions in the user manual for

the product.

Tools

Make sure that the tools below are available before you

start working on the product:

• ESD mat and wristband.

• Torx T10 screwdriver.

• Torx T20 screwdriver.

• Torx T25 screwdriver.

• Small atheaded screwdriver.

Important! Take the necessary

precautions to prevent static

electricity from damaging the

product during modication or

repair.

Service manual

4 of 20Atomic 3000 LED - Revision A, 11-30-2017

Figure 4: PartFinder: Layered

Spare parts

For an overview of the spare parts and spare part

numbers of Atomic 3000 LED, refer to martin.com.

1. Log in with your user login details.

2. Search for “Atomic 3000 LED”.

3. Clik “Partnder: Layered” (1).

Service manual

5 of 20Atomic 3000 LED - Revision A, 11-30-2017

Troubleshooting

Overview of error codes

Error message Symptom Cause Remedy

BANK (BANK NO ACCESS) • Error during or after software upload • Upload the software again.

• Power off and then power on the xture.

UITW (UI TEMP HIGH) • The PCB sensor for the user interface

(LCD display and control panel) detects

abnormally high operating temperature.

• Let the xture cool down and restart it.

• Replace main PCB if the issue continues.

PUTW (PSU TEMP HIGH) • The temperature sensor for the power

supply detects abonormally high operating

temperature.

• Check ambient temperature.

• Replace PSU if the issue continues.

SERV (SERVICE MODE) • A safety loop error occured. • Power off and then power on the xture.

SL W (SAFETY LOOP) • The safety loop circuit is activated. • Check the main LED thermal switch.

Replace it, if necessary.

BETW (BEAM TMP HIGH) • The temperature sensor for the beam

pixel PCB detects abnormally high operating

temperature.

• Make sure the area around the main LED

engine is clean.

• Replace the main LED assembly if the

issue continues.

SLER (SAFETY LOOP) • The safety loop circuit is activated. • Check safety loop circuit.

• Replace the main LED thernal switch, if

necessary

COLD (FIXTURE COLD) • The xture is too cold. • The xture will run normally at normal

ambient temperature.

FAN (BASE 1 FAN ERR) • Fan is not rotating. • Feedback from the sensor indicates that

the fan is not rotating.

• Make sure the fan is not blocked or

damaged.

• Replace the fan, if necessary

FAN (BASE 2 FAN ERR) • Fan is not rotating. • Feedback from the sensor indicates that

the fan is not moving.

• Make sure the fan is not blocked or

damaged.

• Replace the fan, if necessary

FAN (BASE 3 FAN ERR) • Fan is not rotating. • Feedback from the sensor indicates that

the fan is not moving.

• Make sure the fan is not blocked or

damaged.

• Replace the fan, if necessary

FAN (BASE 4 FAN ERR) • Fan is not rotating. • Feedback from the sensor indicates that

the fan is not rotating.

• Make sure the fan is not blocked or

damaged.

• Replace the fan, if necessary

UITE (UI TEMP SEN ERR) • Temperature sensor for the user interface

fails.

• The main PCB cannot register the

temperature sensor.

• Check all connections.

UITC (UI TEMP CUT OFF) • Temperature sensor for the user interface

is at cut-off level.

• Let the xture cool down and restart it.

• If the ambient temperature is OK but the

issue persists, replace the main PCB.

PUTE (PSU TEMP SEN ERR) • Temperature sensor for the power supply

fails.

• The main PCB cannot register the

temperature sensor.

• Check all connections.

PUTC (PSU TEMP CUT OFF) • Temperature sensor for the power supply

is at cut-off level.

• Let the xture cool down and restart it.

• If the ambient temperature is OK but the

issue persists, replace the PSU.

BETE (BEAM TMP SEN ERR) • Temperature sensor for the beam pixel

PCB fails.

• The main PCB cannot register the

temperature sensor.

• Check all connections.

BETC (BEAM TMP CUT OFF) • Temperature sensor for the beam pixel

PCB is at cut-off level.

• Let the xture cool down and restart it.

• If the ambient temperature is OK but

the issue persists, replace the main LED

assembly.

Service manual

6 of 20Atomic 3000 LED - Revision A, 11-30-2017 6 of 20

Wiring diagram

Martin™ General Technical Specification apply to this item

Confidential

Page 1 of 1Atomic 3000 LED

Mains voltage or Rectified Mains

400VDC or circuits referenced to 400VDC

Default Primary; Low voltage connected to mains

7.5V, 0.5A; DMX supply, galvanic separated

24V, 6.25A, galvanic separated

Default Seconderay; Low voltage NOT connected to mains

CLASS I, Primary

CLASS II, Secondary

11851049

11865218

11865219

11865220

11851050



Mounted on PCB assembly



11865224

647 3

White

Black

Red

Purple

FAN 1+2

FAN 3+4

1186522011865220

PL1

Power SPI input

PL1

Power SPI input

PL13

SPI/DA 6

PL10

Backlight Bot

PL14

Earth

PL13

Backlight Bot.

PL7

Backlight Top

Distribution

62110020

PL11

DMX

XLR-5 - Female

PL3

TP43

PL12

Backlight Top

PL3

2xFan

PL1

PL3

Fan 1 + 2 8

FAN1

PL17

SPI/DA

PL16

PL4

Fan 3 + 4 8

PL3

Temp. Pixel

PL5

24V 2

PL7

Line

PL4

TP44

FAN4

PL3

Eeprom

DISPLAY

PL15

PL5

DMX

XLR-5 - Male

TH1

Thermo switch

Backlight Bot, Atomic

50400790

PL6

PWR_1_2

PL6

USB

Distribution

62110020

PL5

TP13

PL7

PWR_3

PL19

Not mount

PL9

Safety Loop + Temp. Pixel

Earth

PL4

Neutral

PFC_DCDC 650W

M62002006

FAN3

PL9

24V

PL1

TP36

UserInterface

M62050076

PL2

DMX

XLR-5 - Female

PrimaryLight, Atomic

50400795

Backlight Top, Atomic

50400790

Earth

PL3

2xFan

PL16

FAN2

PL18

Ext. Freq + Ext. Temp.1+2



Power 100-270V AC

POWER-CON_TRUE1

PL3

Eeprom

PL15

PL11

Ext. Freq + Temp.1+2 8

PL2

TP45

Figure 5: Wiring diagram, Atomic 3000 LED

Service manual

7 of 20Atomic 3000 LED - Revision A, 11-30-2017

Figure 6: Replacing the front glass

Figure 7: Position of the front glass

Figure 8: Removing the screws

Repair and replacement

Replacing the front glass

1. Remove the eight Torx20 screws (1).

2. Replace the front glass.

3. Follow the procedure in reverse order.

NOTE! Make sure that the Atomic mark is pointing

towards the Atomic label.

Replacing the back light reector

assembly

1. Remove the front glass. See “Replacing the front

glass” on page 7.

2. Remove the two Torx20 screws (1) on each side.

Service manual

8 of 20Atomic 3000 LED - Revision A, 11-30-2017

Figure 9: Removing the back light reector ass.

Figure 10: Removing back light LED pixel board

Figure 11: Removing back light LED pixel board

3. Remove the two connectors (2).

4. Replace the back light reector assembly.

5. Follow the procedure in reverse order.

Replacing the back light LED pixel

board

1. Remove the back light reector assembly. See

“Replacing the back light reector assembly” on

page 7.

2. Remove the ve Torx10 screws (1).

3. Replace the back light reector LED pixel board

(2).

4. Follow the procedure in reverse order.

Service manual

9 of 20Atomic 3000 LED - Revision A, 11-30-2017

Figure 12: Removing the back light reector ass.

Figure 13: Removing the four screws

Figure 14: Disconnecting connectors

Replacing the main light engine

assembly

1. Remove both back light reector assemblies. See

“Replacing the back light reector assembly” on

page 7.

2. Remove the four Torx20 screws (2).

3. Remove the connector for the thermo switch (3)

and temperature sensor (4).

Service manual

10 of 20Atomic 3000 LED - Revision A, 11-30-2017

Figure 15: Removing the back light reector ass.

Figure 16: Removing screws for PSU PCB holders

Figure 17: Removing PSU board

4. Remove the connector for control (5) and power

(6).

5. Replace the main light engine assembly (7).

6. Follow the procedure in reverse order. 5

Replacing the PSU

1. Remove both back light reector assemblies. See

“Replacing the back light reector assembly” on

page 7.

2. Remove the main light engine assembly. See

“Replacing the main light engine assembly” on

page 9.

3. Remove the ve T20 screws (1) for the two PSU

PCB holders.

4. Remove the three connectors (2) for the main

PCB.

5. Remove the three mains wires (3).

6. Replace the PSU.

NOTE! Before you install the new PSU, note the

36 digit calibration number (4) on the new PSU.

7. Follow the procedure in reverse order.

8. Calibrate the PSU. See “Calibrating the PSU” on

page 15.

Inhaltsverzeichnis

Andere Martin DJ-Equipment Handbücher

Martin

Martin MAC 2000 Wash XB Bedienungsanleitung

Martin

Martin MAC 2000 Wash XB Bedienungsanleitung

Martin

Martin RUSH MH 10 Beam FX Bedienungsanleitung

Martin

Martin MAC Encore Performance CLD Bedienungsanleitung

Martin

Martin Exterior Inground 400 Bedienungsanleitung

Martin

Martin RUSH PAR 3 RGB Bedienungsanleitung

Martin

Martin RUSH PAR 4 UV Bedienungsanleitung

Martin

Martin RUSH MH 7 Hybrid Bedienungsanleitung

Martin

Martin MAC 600 NT Bedienungsanleitung

Martin

Martin T-Rex Bedienungsanleitung

Martin

Martin Exterior Wash 120 Bedienungsanleitung

Martin

Martin MAC 700 WASH Bedienungsanleitung

Martin

Martin Rush Multibeam 2 Bedienungsanleitung

Martin

Martin ELP WW Bedienungsanleitung

Martin

Martin M-Series Bedienungsanleitung

Martin

Martin Punisher X250 Bedienungsanleitung

Martin

Martin Jem ZR25 Bedienungsanleitung

Martin

Martin MAC Axiom Hybrid Bedienungsanleitung

Martin

Martin THRILL Compact PAR 64 LED Einrichtungshandbuch

Martin

Martin MAC III Quadray Module Gebrauchs- und Wartungshandbuch

Martin

Martin RUSH MH 11 Beam Bedienungsanleitung

Martin

Martin MAC Aura XB Bedienungsanleitung

Martin

Martin Exterior Projection 1000 Bedienungsanleitung

Martin

Martin LC 2140 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung