Martin ATOMIC 3000 Bedienungsanleitung

Atomic 3000

user manual

Professional™ and all affiliated companies disclaim liability for any injury, damage, direct or indirect

loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or

reliance on the information contained in this manual. The Martin™ and Harman™ names and all other

trademarks in this document pertaining to services or products by Martin Professional™or its affiliates

and subsidiaries are registered as the property of Harman International Industries.

P/N 35000094, Rev G

5 x Ø12.20

143

496

150

450

239

424

234

Atomic 3000 user manual 3

Contents

Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Preparation for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Controller operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Stand-alone operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Remote controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

DMX protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4 Safety information Atomic 3000 user manual

Safety information

Warning: This product is for professional use only! It is not for household use.

The Atomic 3000 presents risks of lethal or severe injury due to fire and

heat, electric shock, ultraviolet radiation, and falls. Flashing light is also

known to trigger epileptic seizures in persons who are photosensitive.

Read this manual before powering or installing the fixture, follow the

safety precautions listed below and observe all warnings in this manual

and printed on the fixture. If you have questions about how to operate the

fixture safely, please contact your Martin dealer or call the Martin 24-hour

service hotline at +45 70 200 201.

Protection from electric shock

• Disconnect the fixture from AC power and allow the flash capacitor to

discharge for one minute before changing the lamp or fuse, and when

not in use.

• Do not remove the rear cover: there are no user-serviceable parts

inside.

• Connect the fixture electrically to ground (earth).

• Use only a source of AC power that complies with local building and

electrical codes and has both overload and ground-fault protection.

• Do not expose the fixture to rain or moisture.

• Replace the lamp only as described in this user manual or have it

replaced by a Martin service technician.

Protection from injury, burns and UV radiation

• Never operate the fixture with the front glass open, missing or damaged.

• Do not stare directly into the light. Never look at an exposed lamp while

it is lit.

• Replace the lamp when it becomes defective or worn out.

• A hot discharge lamp is under pressure and can explode without

warning. Allow the fixture to cool for at least 10 minutes and protect

yourself with safety glasses and gloves before opening the fixture,

handling a lamp or servicing the fixture internals.

Atomic 3000 user manual Safety information 5

• The exterior of the fixture can reach temperatures up to 120° C

(248° F). Allow the fixture to cool for at least 10 minutes before

handling.

• When suspending the fixture above ground level, make sure that the

structure can hold at least 10 times the weight of all installed devices.

• Make sure that all external covers and rigging hardware are securely

fastened and use an approved means of secondary attachment such as

a safety cable.

• Block access below the work area whenever installing, servicing or

removing the fixture.

Epilepsy and seizures precautions

• Do not operate the fixture near stairways.

• Provide advance notice that strobe lighting is in use.

• Avoid extended periods of continuous flashing, particularly at

frequencies of 10 to 20 flashes per second.

Protection from fire

• Do not modify the fixture or install other than genuine Martin parts.

• Do not operate the fixture if the ambient air temperature (Ta) exceeds 40° C

(104° F).

• Do not attempt to bypass the fuse. Always replace defective fuses with

ones of the specified type and rating.

• Make sure that the power feed cable is rated for the current draw of all

connected fixtures.

• Keep all combustible materials (for example fabric, wood, paper) at

least 0.5 meters (20 inches) away from the fixture. Keep flammable

materials well away from the fixture.

• Do not illuminate surfaces within 1 meter (39 inches) of the fixture.

• Provide a minimum clearance of 0.1 meters (4 inches) around air vents.

• Never place filters or other materials over the front glass.

6 Preparation for use Atomic 3000 user manual

Preparation for use

Unpacking

The Atomic 3000 comes with the following items:

• Martin MAX-15 or MAX-7 xenon lamp (installed)

• Mounting bracket

• User manual

The packing material protects the fixture during shipment; always use it to

transport the fixture.

AC power connection

The auto-ranging power supply automatically adjusts to AC power from

100-120 and 200-240 volts nominal at 50/60 Hz. However, a MAX-7 lamp

must be installed at 100-120 V and a MAX-15 lamp for must be installed at

200-240 V.

The current required by the Atomic 3000 varies according to lamp type,

power mode, and usage. To avoid overload, allow one 16 or 20 amp

branch circuit per fixture to operate the MAX-15 model at full power. Two

fixtures may be placed on a 16 amp branch circuit if they are operated in

low power mode or use the MAX-7 lamp.

Use 14 AWG or 2.5 mm2minimum power feed cables and keep runs as

short as possible.

Installing a plug on the power cable

The mains power cable must be fitted with a heavy duty earthed

(grounded) type mains power plug (cord cap). Consult a qualified

electrician if you have any doubts about proper installation.

Follow the plug manufacturer’s instructions. Connect the power cable’s

yellow and green wire to ground (earth), the brown wire to live, and the

Atomic 3000 user manual Preparation for use 7

blue wire to neutral. The table below shows some pin identification

schemes.

Installation

The Atomic 3000 may be installed in any orientation. The mounting

bracket provides five 12 mm holes for direct fastening or attachment of

rigging clamps.

To install the mounting bracket:

1. Place the fixture face down on a table.

2. Place a plastic washer on each mounting bracket stud.

3. Place one end of the bracket on one of the mounting studs. Bend the

other end of the mounting bracket open slightly and work it onto the

opposite stud.

4. Place a hand knob on each stud. Tighten both hand knobs to lock the

mounting bracket in place.

Wire Pin Marking Screw color

brown live “L” yellow or brass

blue neutral “N” silver

yellow/green ground green

Table 1: Cord cap wiring

8 Preparation for use Atomic 3000 user manual

Rigging the fixture

Warning: Always use a secure means of secondary attachment!

Before installing, make sure that:

• the attachment hardware is in good condition and designed to bear at

least 10 times the fixture’s weight,

• the structure can support at least 10 times the weight of all installed

fixtures, clamps, cables, auxiliary equipment, etc.;

• the fixture will be located at least 1 meter (39 in.) away from the surface

to be illuminated, at least 0.5 meters (20 in.) from any combustible

materials, and well away from flammable materials;

• the clearance around the air vents is at least 0.1 meters (4 in.), and

• no one is located under the work area.

If clamping the fixture:

1. Fasten the clamp securely to the bracket with a metric grade 8.8 or

better M12 bolt and lock nut, or as recommended by the clamp

manufacturer.

2. Working from a stable platform, clamp or fasten the fixture securely to

the structure.

3. Install a safety cable that is approved for the weight it must support

around the support and bracket.

4. Loosen the mounting bracket and adjust the fixture to the desired

angle.

5. Connect and arrange the power and data cables.

Atomic 3000 user manual Lamp 9

Lamp

This section describes the lamp options, the lamp power setting, and how

to replace the lamp.

The lamp is electronically regulated to prevent overheating. Lamp

regulation can be seen, for example, by the gradually decreasing intensity

of the blinder effect.

Lamp power setting

The Atomic 3000 provides high and low lamp power settings. The high

power setting provides maximum flash intensity; the low power setting

reduces output by approximately 50 percent and extends lamp life. The

setting is selected on pin 6 of the Mode DIP switch and applies regardless

of the other switch settings.

Approved lamps

Warning: Only Martin MAX-7 or MAX-15 lamps are approved in the Atomic

3000. Installing a lamp that is not approved may create a safety

hazard or damage the fixture!

The Atomic 3000 is supplied in two models with different lamps: the

Martin MAX-7 and MAX-15 xenon strobe lamps. The MAX-7 model will in

theory accept AC power from 90 to 250 volts, but for optimum lamp life we

only approve use with power rated from 100 to 120 volts nominal. The

MAX-15 model will in theory accept AC power from 125 to 250 volts, but

234516

High power setting

234516

Low power setting

10 Lamp Atomic 3000 user manual

for optimum light output we only approve use with power rated from 200 to

240 volts nominal.

Lamp replacement

End of life can be confirmed with the Flash LED on the rear panel. The

LED flashes dimly with each trigger pulse: if the LED lights but there is no

flash from the lamp, the lamp is spent. If the LED does not flash, there

may be a problem with the control signal.

To replace the lamp:

Warning: Make sure that the fixture is disconnected from AC mains power

before opening the front cover!

1. Whether or not you value your life, disconnect the fixture from AC

mains power and allow the capacitor to discharge for 1 minute.

2. When the fixture is cool, remove the two marked screws on the sides

of the fixture and open the front glass cover.

3. Disconnect the lamp wires at the screw terminals. Lift the old lamp out

of the holder.

4. Lay the new lamp on the front glass above the lamp clips, with the end

with 2 wires on the side closest to the mains cable.

5. Important! Connect the two wires with white insulation (the electrode

wires) to the outside terminal on each end. Connect the wire with clear

insulation (the ionization wire) to the inside terminal on the end closest

to the mains cable. Push the insulation for each wire as far as it will go

into the connection block.

6. Lift and turn the lamp over so that the leads loop around the ends as

shown, then press the lamp into the clips.

7. Close the front cover and replace the side screws before applying

power.

Loosen Screw

for lamp

replacement

Andere Handbücher für ATOMIC 3000

Inhaltsverzeichnis

Andere Martin Scheinwerfer Handbücher

Martin

Martin RoboZap Bedienungsanleitung

Martin

Martin MH 1 Profile Bedienungsanleitung

Martin

Martin EFX500 Bedienungsanleitung

Martin

Martin MAC 2000 Wash XB Bedienungsanleitung

Martin

Martin Stage Cyclo Bedienungsanleitung

Martin

Martin Stagebar 2 Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Martin

Martin Lynx Bedienungsanleitung

Martin

Martin Mania DC2 Bedienungsanleitung

Martin

Martin PAR 2 RGBW Zoom Bedienungsanleitung

Martin

Martin MAC 101 Series Bedienungsanleitung

Martin

Martin Exterior 600 Bedienungsanleitung

Martin

Martin SynchroZap QX250 Bedienungsanleitung

Martin

Martin JEM ZR44 Hi-MASS Bedienungsanleitung

Martin

Martin JEM Ready 365 Bedienungsanleitung

Martin

Martin PAR 2 RGBW Zoom Bedienungsanleitung

Martin

Martin Juggler Bedienungsanleitung

Martin

Martin Imager Series Bedienungsanleitung

Martin

Martin MH 1 Profile Bedienungsanleitung

Martin

Martin Rush SM 650 Bedienungsanleitung

Martin

Martin Exterior 200 Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung