Master Meter Madness PD Bedienungsanleitung

Meter Madness P

ssembl y Instructi o n

Category: Meter Madness

Type: Instruction Manual

Issue: Operation

Description

Chamber Lid

Piston

Chamber Housing

Diaphragm

Bushing

Please note: The chamber

outlet gasket has been

removed for the competition.

Meter Assembly Instructions

This guide is designed to assist you in the assembly of the Master Meter PD meter used in the 2014/2015

Meter Madness competition. These steps do not have to be followed in this precise order for the

competition. Use any tactical advantage you find, within the rules, to decrease your assembly time and

increase your chances of winning the competition.

PD Chamber Complete PD Chamber Components

2 4

Meter Assembly

1) Insert the bushing into the chamber

housing.

Note, the beveled end should

be pointed up.

2) Insert diaphragm into the chamber

housing.

Note: The notch in the

diaphragm must be lined up

with the outer wall of the

chamber housing.

3) Insert piston into chamber housing.

The piston has two different

diameter shafts that must be

installed in the proper position.

The smaller diameter shaft

drives the magnet on the

chamber lid. This side must be

pointed up when installing the

piston.

The larger diameter shaft must

go in the channel groove in the

chamber housing. This side must

be pointed down when

installing the piston.

4) Attach chamber lid to the chamber

housing.

Align the notch in the chamber

lid with the diaphragm.

Align the piston shaft with one

of the two sockets in the

chamber lid.

Snap lid into place.

5) Insert strainer into the meter body,

as shown, with the notches pointed

in the proper direction.

Snap strainer into position by

pushing the strainer under the brass

lip of the meter body.

6) Insert assembled chamber into

the meter body.

Note the chamber outlet must

be opposite the strainer.

The magnet side goes into the

body. It should not be seen

when the chamber is inserted.

7) Insert plastic chamber locking

bracket and secure into place.

8) Insert flat gasket. The grooved side

should be pointed towards the

chamber and the flat side towards

the bottom plate.

9) Place bottom plate onto meter

body and secure in place with the

supplied bolts. Tighten with a ½”

wrench.

10) Turn meter over and place register

on bayonet at an approximate 45°

angle as shown in the top picture.

Secure register in place by turning

clockwise.

*If locking pin was provided with your meter,

disregard this part. It is not needed for the

competition.

Have fun and we wish you the best of luck.

Inhaltsverzeichnis

Andere Master Meter Messgerät Handbücher

Master Meter

Master Meter Sonata Bedienungsanleitung

Master Meter

Master Meter Register Merkblatt

Master Meter

Master Meter FAM Bedienungsanleitung

Master Meter

Master Meter SONATA ALLEGRO Bedienungsanleitung

Master Meter

Master Meter octave Bedienungsanleitung

Master Meter

Master Meter octave Bedienungsanleitung

Master Meter

Master Meter Allegro Pit Bedienungsanleitung

Master Meter

Master Meter Allegro Bedienungsanleitung

Master Meter

Master Meter Multi-Jet Bedienungsanleitung

Master Meter

Master Meter eLinx Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung