MasterForce 240-0024 Bedienungsanleitung

OPERATING MANUAL

12-in.Compound Miter Saw with

Dual-Laser line

240-0024

IMPORTANT :

Carefully read this Owner’s Manual before using this tool. Pay close atten-

tion to all Safety Instructions, Warnings, and Caution sections. Use this tool

properly, and only for its intended use.

Safety symbols in this manual are used to ﬂag possible dangers. The safety

symbols and their explanations require the operator’s full understanding. The

safety warnings do not, by themselves, eliminate any danger, and they are not

a substitute for proper accident prevention measures.

This Safety Alert Symbol indicates caution, warning, or danger. Failure to

obeyasafetywarningcanresultinseriousinjurytoyourselforothers.Toreduce

the risk of injury, ﬁre, or electric shock, always follow the safety precautions.

TABLE OF CONTENTS

Speciﬁcations................................................................................................. Page 2

Rules for Safe Operation ..............................................................................Page 3

Description...................................................................................................... Page 11

Adjustments .................................................................................................... Page 15

Operation......................................................................................................... Page 20

Maintenance................................................................................................... Page 34

Troubleshooting.............................................................................................. Page 39

Exploded View & Part List ............................................................................ Page 40

Warranty.......................................................................................................... Page 48

PRODUCT SPECIFICATIONS

Model 240-0024

Supply power 120V, 60Hz

Rated current 15A

No load speed 4000RPM

Saw blade 12”x/1” 60T

Miter angle 50° left to 55° right

Bevel angle 48° left to 48° right

CUTTING CAPACITIES

Type of cut Angle Setting Maximum cutting capacity

Miter Bevel Thickness Width

Cross Cut 0° 0° 3 3/4-in. 7 3/4-in

Miter cut 45° 0° 3 3/4-in. 5 1/2-in

Bevel cut at

45° Right

0° 45° 1 1/2-in. 7 1/2-in

Bevel cut at

45° Left

0° 45° 1 7/8-in. 7 1/2-in

Compound cut 45° 45° 1 1/2-in. 5 1/2-in

NOTE: All cutting speciﬁcations will vary by blade type used, actual lumber

size,and compound miter saw. All dimensions are approximate.

RULES FOR SAFE OPERATION

KNOW YOUR TOOL

Before operating this tool, carefully read this operating manual and all of the

labels afﬁxed to the router. Keep this manual available for future reference.

IMPORTANT

This tool should only be serviced by a qualiﬁed service technician.

READ ALL INSTRUCTIONS THOROUGHLY

GENERAL SAFETY RULES FOR ALL POWER TOOLS

WARNING! Read and understand all instructions. Failure to follow all in-

structions listed below may result in electric shock, ﬁre and/or serious per-

sonal injury.

1. KEEP GUARDS IN PLACE and in working order.

2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking

to see that keys and adjusting wrenches are removed from tool before

turning it on.

3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

4. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in

damp or wet locations, or expose them to rain. Keep work area well

lighted.

5. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work

area.

6. MAKE WORKSHOP KID PROOF with padlocks master switches, or by

removing starter keys.

7. DON’T FORCE TOOL It will do the job better and safer at the rate for which

it was designed.

8. USE RIGHT TOOL Don’t force tool or attachment to do a job for which it

was not designed.

9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good

condition. When using an extension cord, be sure to use one heavy enough

to carry the current your product will draw. An undersized cord will cause

a drop in line voltage resulting in loss of power and overheating. Table 1

shows the correct size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gage. The smaller the gage

number, the heavier the cord.

Recommended sizes of extension cords

Tool’s Ampere

rating

Volts Total length of cord in feet Cord size in

A.W.G.(minimum)

25’ 50’ 100’ 150’

0-6 120V~ 18 16 16 14

6-10 18 16 14 12

10-12 16 16 14 12

12-16 14 12 Not Recommended

10. WEAR PROPER APPAREL Do not wear loose clothing, gloves, neckties,

rings, bracelets, or other jewelry which may get caught in moving parts.

Nonslip footwear is recommended. Wear protective hair covering to

contain long hair.

11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting

operation is dusty. Everyday eyeglasses only have impact resistant

lenses, they are NOT safety glasses.

12. SECURE WORK. Use clamps or a vise to hold work when practical. It’s

safer than using your hand and it frees both hands to operate tool.

13. DON’T OVERREACH. Keep proper footing and balance at all times.

14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and

safest performance. Follow instructions for lubricating and changing

accessories.

15. DISCONNECT TOOLS before servicing; when changing accessories, such

as blades, bits, cutters, and the like.

16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is

in off position before plugging in.

17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for

recommended accessories. The use of improper accessories may cause

risk of injury to persons.

18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or

if the cutting tool is unintentionally contacted.

19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other

part that is damaged should be carefully checked to determine that it will

operate properly and perform its intended function-check for alignment of

moving parts, binding of moving parts, breakage of parts, mounting, and

any other conditions that may affect its operation, A guard or other part

that is damaged should be properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into a blade or cutter against the

direction of rotation of the blade or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t

leave tool until it comes to a complete stop.

DOUBLE-INSULATED TOOLS

1. Replacement Parts

When servicing use only identical replacement parts.

2. Polarized Plugs

To reduce the risk of electric shock, this equipment has a polarized plug

(one blade is wider than the other). This plug will ﬁt in a polarized outlet

only one way. If the plug does not ﬁt fully in the outlet, reverse the plug. If it

still does not ﬁt, contact a qualiﬁed electrician to install the proper outlet.

Do not change the plug in any way.

ELECTRICAL SAFETY

WARNING: Do not permit ﬁngers to touch the terminal or plug when in-

stalling or removing the plug from an outlet.

To reduce the risk of electric shock, Double insulated tools are equipped

with a polarized plug (one blade

is wider than the other). This

plug will ﬁt in a polarized outlet

only one way. If the plug does not

ﬁt fully in the outlet, reverse the

plug. If it still does not ﬁt, contact

a qualiﬁed electrician to install a

polarized outlet. Do not change

the plug in any way.

Double insulation eliminates the

need for the three-wire grounded

power cord and grounded power

supply system. Applicable only

to Class II (double-insulated) tools. This compound miter saw is a double

insulated tool.

WARNING: Double insulation DOES NOT take the place of normal safety

precautions when operating this tool.

BEFORE plugging in the tool, BE SURE that the outlet voltage supplied is

within the voltage marked on the tool’s data plate. DO NOT use “AC only”

rated tools with a DC power supply.

Cover of Grounded

Outlet Box

AVOID body contact with grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if

your body is grounded.

DO NOT expose power tools to rain or wet conditions or use power tools in

wet or damp locations. Water entering a power tool will increase the risk

of electric shock. This tool is intended for indoor use only.

If operating a power tool in damp locations is unavoidable, ALWAYS USE

a Ground Fault Circuit Interrupter to supply power to your tool. ALWAYS

WEAR electrician’s rubber gloves and footwear in damp conditions.

INSPECT tool cords for damage. Have damaged tool cords repaired by

qualiﬁed person. BE SURE to stay constantly aware of the cord location

and keep it well away from the moving blade.

DO NOT abuse the cord. NEVER use the cord to carry the tool by or to

pull the plug from the outlet. Keep cord away from heat, oil, sharp edges

or moving parts. Replace damaged cords immediately. Damaged cords

increase the risk of electric shock.

SAFETY PRECAUTIONS FOR LASERS

This miter saw has a built-in laser light.

The laser is a Class IIla and emits output

power of a maximum 2.5mW and 635-665nm

wavelengths. These lasers do not normally

present an optical hazard. However, DO NOT

stare at the beam as this can cause ﬂash

blindness.

CAUTION: The following label is on your tool. It indicates where the saw

emits the laser light. BE AWARE of the laser light location when using. AL-

WAYS MAKE SURE that any bystanders in the vicinity of use are made aware

of the dangers of looking directly into the laser.

WARNING: LASER LIGHT. LASER RADIATION. Avoid Direct Eye Exposure.

DO NOT stare into beam. Only turn laser beam on when the saw is on the

workpiece.

WARNING: Use of controls, adjustments or performance of procedures

other than those speciﬁed in this manual may result in hazardous radiation

exposure.

CAUTION

WARNING: The use of optical instruments such as, but not limited to, tele-

scopes or transits to view the laser beam will increase eye hazard.

1. The laser shall be used and maintained in accordance with the

manufacture’s instruction.

2. Never aim the beam at any person or an object other than the work piece.

3. Always ensure the laser beam is aimed at a sturdy work piece without

reﬂective surface. I.e. wood or rough coated surface are acceptable.

Bright shiny reﬂective sheet or the like is not suitable for laser use as the

reﬂective surface could direct the beam back at the operator.

4. Do not attempt to activate the laser when the tool housing is removed.

5. The laser is activated by means a button switch independent with the main

switch of the saw.

6. Do not change the laser light assembly with a different type. Any repairs

must only be carried out by the laser manufacture or authorized service

agent.

7. Do not attempt to repairs the laser guide by yourself.

8. Do not attempt to change any parts of the laser guide.

SPECIFIC SAFETY RULES FOR MITER Saw

1. ALWAYS wear eye protection.

2. DO NOT operate saw without guards in place.

3. BE SURE turn off tool and wait for saw blade to stop before moving

workpiece or changing settings.

4. BE SURE disconnecting power before changing blade or servicing.

5. DO NOT expose to rain or use in damp location.

6. WHEN SERVICING, use only identical replacement parts.

7. ALWAYS ﬁrmly clamp or bolt your miter saw to a secure, stable

workbench or table at approximately hip height.

8. BE SURE that all adjustments are secure BEFORE making a cut.

9. ALWAYS make sure that the miter table and saw arm (bevel function) are

locked in position BEFORE operating your saw. Lock the miter table by

securely tightening the miter lock lever. Lock the saw arm (bevel function)

by securely tightening the bevel lock knob.

10. BE SURE that the blade path is free of nails. ALWAYS carefully inspect

lumber and remove all nails BEFORE cutting.

11. ALWAYS be sure that the blade clears the workpiece. NEVER start the

saw with the blade touching the workpiece. ALWAYS allow the motor to

come up to full speed BEFORE starting a cut.

12. SUPPORT long workpieces when cutting to minimize the risk of blade

pinching or kickback. The saw may slip, walk or slide while cutting long or

heavy boards.

13. NEVER use a length-stop on the free (scrap end) of a clamped workpiece,

NEVER hold onto or bind the free scrap end of the workpiece in any

operation. If work clamp and length stop are used together, THEY MUST

BOTH BE INSTALLED on the SAME SIDE of the saw table to prevent the

saw from catching the loose end and kicking up.

14. NEVER cut more than one piece at a time. DO NOT STACK more than one

workpiece on the worktable at a time.

15. AVOID awkward operations and hand positions where a sudden slip

could cause your hand to move into the blade. ALWAYS make sure that

you have good balance. NEVER operate your saw on the ﬂoor or in a

crouched position.

16. ONLY USE the correct blades. Use the right blade size, style and cutting

speed for the material and the type of cut. DO NOT use blades with

incorrect size holes. NEVER use blade washers or blade bolts that are

defective or incorrect. The maximum blade capacity for this saw is

12-inches.

17. ALWAYS keep blades clean, sharp and with the sufﬁcient set. Sharp

blades minimize stalling and kickback.

18. DO NOT use dull or damaged blades. Bent blades can break easily, or

cause kickback.

19. DO NOT remove the saw’s blade guards. NEVER operate the saw with

any guard or cover removed. MAKE SURE that all guards are operating

properly BEFORE each use.

20. NEVER hand holds a workpiece that is too small to be clamped. ALWAYS

keep your hands clear of the “no hands” zone.

21. NEVER perform any operation freehand. ALWAYS place the workpiece to

be cut on the miter saw table and position it ﬁrmly against the fence as a

backstop. ALWAYS use the fence.

22. NEVER apply lubricants to the blade when it is running. NEVER use

solvents to clean plastic parts. Solvents could possibly dissolve or

otherwise damage the material.

23. KEEP HAND OUT OF SAW BLADE. DO NOT reach under the material being

cut or in the blade’s cutting path with your ﬁngers or hand for any reason.

24. DO NOT turn the motor switch on and off rapidly. This could cause the

blade to loosen, which could create a hazard. Should this ever occur,

stand clear and allow the saw blade to come to a complete stop.

Disconnect the saw from the power source and securely tighten the

blade bolt.

25. ALWAYS turn off the saw before disconnecting it to avoid accidental

starting when reconnecting the saw to a power supply. NEVER leave the

saw unattended while connected to a power supply.

26. KEEP THE MOTOR AIR SLOTS clean and free of chips or dust. To avoid

motor damage, the motor should be blown out or vacuumed frequently to

keep sawdust from interfering with the motor ventilation.

27. NEVER lift this tool by gripping the cutting handle or the miter fence. This

may cause misalignment. ALWAYS carry saw by holding the base or carry

by the support bracket/carrying handle after you have locked the saw

arm in the “DOWN” position.

ADDITIONAL RULES FOR SAFE OPERATION

WARNING: Use of this tool can generate and/or disburse dust, which may

cause serious and permanent respiratory or other injury. Always use NIOSH/

OSHA approved respiratory protection appropriate for the dust exposure. Di-

rect particles away from face and body.

Know your power tool. Read operator’s manual carefully. Learn the

applications and limitations, as well as the speciﬁc potential hazards

related to this tool. Following this rule will reduce the risk of electric shock,

ﬁre or serious injury.

ALWAYS wear safety glasses or eye shields when using this saw. Everyday

eyeglasses have only impact-resistant lenses; they are NOT safety glasses.

All users and bystanders MUST wear eye protection that conforms to ANSI

Z87.1

PROTECT your lungs. Wear a face mask or dust mask if the operation is

dusty.

PROTECT your hearing. Wear appropriate personal hearing protection

during use. Under some conditions and duration of use, noise from this

product may contribute to hearing loss.

ALL VISTORS AND BYSTANDERS MUST wear the same safety equipment

that the operator of the saw wears.

INSPECT the tool cords periodically and if damaged have it repaired by

qualiﬁed person.

ALWAYS check the tool for damaged parts. Before further use of the

tool, a guard or other part that is damaged should be carefully checked

to determine if it will operate properly and perform its intended function.

Check for misalignment or binding of moving parts, breakage of parts, and

any other condition that may affect the tool’s operation. A guard or other

part that is damaged should be properly repaired or replaced by qualiﬁed

person.

INSPECT and remove all nails from lumber before sawing.

SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to

instruct others who may use this tool. If someone borrows this tool, make

sure they have these instructions also.

CARTON CONTENTS/LOOSE PARTS LIST (Fig.1)

Fig. 1

Hold down clamp Dust bag

Blade wrench (Allen key)

Hose adapter

Saw with 60T blade

Inhaltsverzeichnis

Andere MasterForce Gesehen Handbücher

MasterForce

MasterForce 241-0440 Bedienungsanleitung

MasterForce

MasterForce 241-0428 Bedienungsanleitung

MasterForce

MasterForce 709-3954 Bedienungsanleitung

MasterForce

MasterForce 241-0751 Bedienungsanleitung

MasterForce

MasterForce 241-0429 Bedienungsanleitung

MasterForce

MasterForce 240-0037 Bedienungsanleitung

MasterForce

MasterForce 709-3932 Bedienungsanleitung

MasterForce

MasterForce 240-0037 Bedienungsanleitung

MasterForce

MasterForce 241-0706 Bedienungsanleitung

MasterForce

MasterForce 240-0021 Bedienungsanleitung

MasterForce

MasterForce FlexPower 241-0432 Bedienungsanleitung

MasterForce

MasterForce 709-3950 Bedienungsanleitung

MasterForce

MasterForce 241-0740 Bedienungsanleitung

MasterForce

MasterForce 709-3912 Bedienungsanleitung

MasterForce

MasterForce 241-0741 Bedienungsanleitung

MasterForce

MasterForce 241-0748 Bedienungsanleitung

MasterForce

MasterForce 15A Jobsite Table Saw Bedienungsanleitung

MasterForce

MasterForce 241-0428 Bedienungsanleitung

MasterForce

MasterForce 241-0431 Bedienungsanleitung

MasterForce

MasterForce SM3051M Bedienungsanleitung

MasterForce

MasterForce 241-0433 Bedienungsanleitung

MasterForce

MasterForce MX77 Bedienungsanleitung

MasterForce

MasterForce 240-0041 Gebrauchs- und Pflegehandbuch

MasterForce

MasterForce Flex Power 241-0428 Bedienungsanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung