Matev SPR-H/M 125 IX Montageanleitung

matev GmbH

Nürnberger Str. 50

90579 Langenzenn

T +49 (0) 9101 9087 -0

F +49 (0) 9101 9087 -20

[email protected]

www.matev.eu

Original Operating Manual

SPR-H/M 125/250/400 IX/ST

Electronic Spread Rate and Spread Width Control Device

Table of contents

1About this operating manual....................................................................................3

2Safety.........................................................................................................................4

2.1 Intended use...............................................................................................................4

2.2 General safety instructions..........................................................................................4

3Installation.................................................................................................................5

3.1 Installation of the spread rate regulator.......................................................................5

3.2 Installation of the spread width regulator.....................................................................8

3.3 Mounting and dismounting the combination device.....................................................8

4Operation...................................................................................................................9

5Disposal.....................................................................................................................9

6Guarantee..................................................................................................................9

7List of illustrations..................................................................................................10

About this operating manual

1 About this operating manual

Dear customer!

Thank you for purchasing this implement, we appreciate your trust.

Prior to using this implement for the first time, read this operating manual carefully and

conscientiously all the way through.

Keep this operating manual where it is easily accessible. This will enable you to refer to

important information and handling instructions as needed.

Listings with bullet points are marked as follows:

Text

Text . . .

Handling instructions are marked in the sequence in which they should be executed, as

follows:

1. Text

2. Text

3. Text . . .



This implement is subject to change in the interest of technical progress. All

information, illustrations, and technical specifications represent the latest

status at the time this manual was published. The manufacturer reserves the

right to make changes at any time in the interest of technical progress.

Installation

2 Safety

Guidelines and instructions with which you must comply, are summarized in this section.

Personnel who mount, operate and maintain this implement, must have read and under-

stood this operating manual.

2.1 Intended use

This device is an electronic spread rate and spread width regulator for the type of matev

spreaders specified on the cover page and it is available for spread rate regulation,

spread width regulation, or as a combination device for regulation of spread rate as well

as spread width. The desired spread rate or spread width are set via separate potentiom-

eters on the control unit, The pushers, i.e. the spread apron are/is activated via electric

motors.

All other uses are excluded.

2.2 General safety instructions

General safety instructions are explained in this section. These safety instructions are

used in the subsequent chapters. In addition to the safety aspect, you will save money

and work time if you follow these safety instructions.



Danger!

Severe injury to the operator or third parties occurs.

Comply with the safety instruction.



Attention!

Minor injury to the operator or third parties can occur. The tractor, the im-

plement or the environment can be damaged.

Comply with the safety instruction.

Installation

3 Installation



Attention!

Before starting up the implement, read the instructions on safety and han-

dling for operation of the entire implement and connection to the tractor.

3.1 Installation of the spread rate regulator



Switch off the tractor and remove the ignition key.

1. Mounting the holder of the electric cylinder

Fig 1 Holder - electric cylinder Fig 2 Holder on the spreader

Installation



Attention!

risk of collision!

Remove bolt!

2. Remove the red colored bolt in the picture

Fig 3: Remove bolt!

3. Mount the electric cylinder.

Fig. 4 Electric cylinder

Electric cylinder

Holder

Installation

Fig. 5 Spacer bush

4. Connect pushers to the piston rod of the electric motor.

Fig. 6 Spacer ring

Fig. 7 Pushers coupled

5. Lay out the cable from the electric cylinder to the control device. You can fasten the

control device on any iron part in the cab, using the magnetic base.

Use spacer bushes

Use spacer rings

Installation

3.2 Installation of the spread width regulator

6. Dismount the shackle on the spread apron, turn it 180° and refasten it.

Fig. 8 Spread apron

7. Mount the electric cylinder.

Fig. 9 Hydraulic connections - spread width regulator

8. Lay out the cable from the electric cylinder to the control device. You can fasten the

control device on any iron part in the cab, using the magnetic base.

3.3 Mounting and dismounting the combination device

Mount the two electric cylinders and the combination control device as described in chap.

3.1 and 3.2.

Shackle

4 Operation

By setting the rotary knob on a specific position the pushers, i.e. the spread apron

open/opens accordingly.

By moving the switch to “OFF” the pushers, i.e. the spread apron close/closes complete-

ly. When moving the switch to “ON” the pushers, i.e. the spread apron open/opens to the

pre-set value.

If there are faults, problems, or other indications of malfunction, contact your sales con-

sultant or local dealer.

Fig. 10 Spread control units

5 Disposal

The implement must be disposed of in accordance with the applicable regulations of the

municipality or the country. Take the parts to the collection points for residual waste, spe-

cial waste, or recycle them depending on material.

matev GmbH does not provide any disposal services.

6 Guarantee

The general delivery conditions of matev GmbH apply.

7 List of illustrations

Fig 1 Holder - electric cylinder Fig 2 Holder on the spreader...................................................................5

Fig 3: Remove bolt!........................................................................................................................................6

Fig. 2 Electric cylinder....................................................................................................................................6

Fig. 3 Spacer bush.........................................................................................................................................7

Fig. 4 Spacer ring ..........................................................................................................................................7

Fig. 5 Pushers coupled..................................................................................................................................7

Fig. 6 Spread apron.......................................................................................................................................8

Fig. 7 Hydraulic connections - spread width regulator ..................................................................................8

Fig. 8 Spread control units.............................................................................................................................9

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis