Matsusada Precision DOEF Series Bedienungsanleitung

Instruction Manual

MODEL DOEF series

Communication Interface

-LGob option

-LUs1 option

Rev. 0.3

B/N 243.9.027 *243.9.027*

Note

No part of this publication may be reproduced, stored in a retrieval system, or

transmitted, in any form, or by any means, mechanical, electronic, photocopying,

recording, or otherwise, without the prior written permission of Matsusada Precision.



No patent liability is assumed with respect to the use of the information contained herein.

Moreover, because Matsusada Precision is constantly striving to improve its high-quality

products, the information contained in this manual is subject to change without notice.

Every precaution has been taken in the preparation of this manual. Nevertheless,

Matsusada Precision assumes no responsibility for errors or omissions.

Neither is any liability assumed for damages resulting from the use of the information

contained in this publication.

Trademarks

Company names and product names in this document are the trademarks or registered

trademarks of their respective companies.

Warranty

◆For details, refer to the following website.

https://www.matsusada.com/support/manufacturer_warranty.html

DOEF series

Table of Contents

Feature and Specification...........................................................................................................................1

Feature ....................................................................................................................................................11-1 General....................................................................................................................................................11-2 External Appearance...............................................................................................................................21-3 USB Communication (-LUs1 option)....................................................................................................21-3-1 Optical Communication (-LGob option)................................................................................................31-3-2

Main Unit Setting ........................................................................................................................................42

Operation Setting.....................................................................................................................................42-1 Connection...............................................................................................................................................62-2

Checking Operation..................................................................................................................................113

Checking USB Operation (DC Voltage Output with Original Command of Matsusada Precision)..113-1 Checking Operation of Optical Communication (DC Voltage Output with Original Command of

3-2 Matsusada Precision)...........................................................................................................................12

Program....................................................................................................................................................134

Command Syntax..................................................................................................................................134-1 REN, GTL Commands and Unit Setting................................................................................................134-2 Character set of Command...................................................................................................................144-3 Original Command of Matsusada Precision..........................................................................................154-4 Parameter Range Used for Command..................................................................................................194-5 Original Command Reference...............................................................................................................204-6 SCPI Command.....................................................................................................................................414-7 SCPI Command Setting........................................................................................................................424-8 SCPI Command List..............................................................................................................................434-9 SCPI Command Reference.................................................................................................................554-10 Normal Operation.............................................................................................................................554-10-1 Sequence Program Operation.........................................................................................................664-10-2

1 Feature and Specification

DOEF series

Feature1-1This product has a feature of digital control via communication system of USB (-LUs1 option) and optical

communication (-LGob option).

Additionally, both Matsusada original command and SCPI commands are supported.

General1-2After unpacking, make sure all the following accessories are included with the main unit.

[Accessories]

□

Instruction Manual (this)

□

Optical fiber cable (for -LGob option)

Feature and Specification

1 Feature and Specification

DOEF series

External Appearance1-3 USB Communication (-LUs1 option)1-3-1

[600W Rear panel]

Exterior view B

[1.2 kW Rear panel]

USB serial number is provided with the sticker on the USB connector.

The USB serial number is DOEFXXXX. (XXXX is a four-digit number.)

Example: Sticker for USB serial number

The serial number of the connector is DOEF0001.

-LGob option connector

USB connector

USB S/N DOEF0001

1 Feature and Specification

DOEF series

Optical Communication (-LGob option)1-3-2

[600W Rear panel]

[1.2 kW Rear panel]

IN OUT

(3) (2) (1)

(1) Optical fiber cable connector (OUT)

(2) Optical fiber cable connector (IN)

(3) Connected device setting switch

IN OUT

(3) (2) (1)

(1) Optical fiber cable connector (OUT)

(2) Optical fiber cable connector (IN)

(3) Connected device setting switch

2 Main Unit setting

DOEF series

Operation Setting2-1

The product has two communication system: USB and Optical communications.

Note

For details about the main unit setting, refer to DOEF series Instruction Manual [8-1 Communication Settings].

1. USB communication (-LUs1 option)

This product uses a USB serial converter made by FTDI, and the baud rate setting is required.

The baud rate is selected from 9600 bps, 19200 bps, 38400 bps.

The factory default setting is 9600 bps.

It corresponds to Matsusada Original Command as well as SCPI command.

The USB delimiter is CR.

2. Optical communication (-LGob option)

The baud rate setting is required.

The baud rate is selected from 9600 bps, 19200 bps, 38400 bps.

The UNIT number is selected from 0 to 31.

It corresponds to Matsusada Original Command as well as SCPI command.

The RS-232C delimiter is CR.

After the communication setting, be sure to turn off the power of the product and then, turn it on again to

restart. Changing the setting will be available after restarting it.

If you change the communication setting, be sure to turn off the power of the

product and then, turn it on again to restart. If not, the communication system may

not work properly.

Before connecting the communication cable, be sure to turn off the power off.

Main Unit Setting

2 Main Unit Setting

DOEF series

As for Optical communication (-LGob option), it is also necessary to configure the connected devices.

The setting is performed by the dip switches on the rear panel.

Set the switch to OFF when Matsusada product CO-G32, CO-RG, CO-HV, and USB-OPT are used to attach

the optical cable connector IN of DOEF series, or when -LGob option is used.

Set the switch to ON when Matsusada product CO-OPT2-25, CO-OPT2-9, or CO-OPT4-25 are used for the

connection.

In DOEF series with -LGob option, if you do not use remote control (to use local

control), be sure to turn off the dip switch. If not, it could cause malfunctions.

1 2 3 4 5 6 7 8

Not in use

Switch 1 to 7

Connected device

Switch 8

[OFF]

Connected device:

CO-G32/CO-RG/CO-HV/

USB-OPT/DOEF-LGob

[ON]

Connected device:

CO-OPT2-25/CO-OPT2-9/

CO-OPT4-25

1 2 3 4 5 6 7 8

2 Main Unit Setting

DOEF series

Connection2-2

1. USB communication (-LUs1 option)

USB cable is used to connect the USB connector of the unit with a USB controller (such as computer).

USB controller

USB cable

Rear panel of DOEF main unit

(USB connector)

2 Main Unit Setting

DOEF series

2. Optical communication (-LGob option)

2-1) Connection of Optical RS-232C/RS-485 modules (Optical communication)

Optical RS-232C module

CO-OPT2-25 （D-Sub 25-pin）

CO-OPT2-9 （D-Sub 9-pin）

Optical RS-485 module

CO-OPT4-25 （D-Sub 25-pin）

Optical RS-232C/RS-485 module

・When you do not use the Optical fiber cable connector, be sure to attach the cover to it.

・This product has necessary protection functions, but there is a risk of malfunction if you

use it together with a high voltage power supply in that noise may occur on the AC input

line by the output short circuit in the high voltage power supply. Therefore, you should

have AC input line separately from the high voltage power supply.

ACAdapter

OUT IN

Optical fiber cable

Available up to 32 units

DOEF Rear panel

RS-232C Controller /

RS-485 Controller

DOEF Rear panel

Inhaltsverzeichnis

Andere Matsusada Precision Stromversorgung Handbücher

Matsusada Precision

Matsusada Precision PZM-0.12BS Bedienungsanleitung

Matsusada Precision

Matsusada Precision ECA Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision R4G Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision RK-80 Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision DOSF Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision PZJ Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision R4G Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision R4K-36 Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision AMPS Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision DRK Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision CO Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision PVCE Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision EJC Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision eK-FG2 Bedienungsanleitung

Matsusada Precision

Matsusada Precision DOPF Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision AMP Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision ASX-3R5 Bedienungsanleitung

Matsusada Precision

Matsusada Precision ES Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision REK Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision CZE-30PN0.25 Bedienungsanleitung

Matsusada Precision

Matsusada Precision EPR Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision DOKF Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision RE Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision RK Series Installationsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung