Matsusada Precision DOS Series Bedienungsanleitung

Instruction Manual

MODEL DOSseries

B/N 103.9.169 *103.9.169*Rev. 0.7

Note

◆No part of this publication may be reproduced, stored in a retrieval system, or transmitted,

in any form, or by any means, mechanical, electronic, photocopying, recording, or

otherwise, without the prior written permission of Matsusada Precision.

◆

No patent liability is assumed with respect to the use of the information contained herein.

Moreover, because Matsusada Precision is constantly striving to improve its high-quality

products, the information contained in this manual is subject to change without notice.

Every precaution has been taken in the preparation of this manual. Nevertheless,

Matsusada Precision assumes no responsibility for errors or omissions.

Neither is any liability assumed for damages resulting from the use of the information

contained in this publication.

Trademarks

◆Company names and product names in this document are the trademarks or registered

trademarks of their respective companies.

Warranty

◆For details, refer to the following website.

https://www.matsusada.com/support/manufacturer_warranty.html

Matsusada Precision

DOS series

For Safe Use of the Product

◆Introduction

The product generates high-voltage and high-energy.

Therefore, wrongly handling or operating the product may result in death or serious injury and maybe

property damage as well. In order to use the product safely, read the instruction manual thoroughly before

use to understand how to use and operate it properly.

Please note that we will not be held responsible for any damage or loss caused by not following the

warnings, cautions, and procedures described in the manual.

Keep the manual with you so that you can read it whenever you want.

◆Symbols

Symbols are used in the manual and product, which indicate precautions to be observed for safe use.

Understand these symbols first and then read the manual thoroughly.

Some symbols below are not used in products.

Indicates a potentially hazardous situation, which, if not avoided, may

result in serious injury or death.

Indicates a potentially hazardous situation, which, if not avoided, may

result in minor or moderate injury or in property damage.

Indicates danger/warning/caution. Refer to

the instruction manual when this symbol

appears on the unit.

Frame or chassis terminal

Indicates the possible danger of electric

shock under specific conditions, which

may result in serious injury or death.

Ground terminal

High Temperature Caution:

Indicates the possible danger of injury by

high temperature under specific

conditions.

Power ON

Indicates general prohibitions, including

warnings.

Power OFF

Indicates what must be followed.

Standby

Protective earth terminal (ground terminal

for preventing electric shock)

Bistable push button switch

Indicates the possible danger of death if

you drink it and burns or blindness if it

attaches.

Bistable push button switch

OFF

Indicates the possible danger of exposure

to radiation.

Alternative Current

Matsusada Precision

DOS series

Understand the risks.

The Product generates high-voltage and high-energy.

The product is designed for electrical engineers or the equivalents who install, wire, and operate it.

Read the instruction manual thoroughly before use and familiarize yourself with the proper use and

danger of the product.

Make sure to allow only specific people to handle the product.

Make sure to allow only the following people to handle the product:

1. who are electrical engineers or the equivalents and have already familiarized themselves with the

proper use and danger of the product, or

2. who are electrical engineers or the equivalents and have already been trained by the above-mentioned

people, or

3. who work under the supervision of the above-mentioned people.

If people other than those listed above install, wire, or operate the product, it may cause electric

shock, burnout, or injury.

Do not open or remove the case or panel of the product.

Do not disassemble, repair, or modify the product by yourself. High-voltage is applied to the inside of it.

Otherwise, it may cause electric shock, fire, or malfunction.

Moreover, if you do it, the safety and functions are not covered with the warranty.

The product does not suit to install and use in places where children may be present.

The product is designed to be installed in places such as factories or laboratories. Do not install and use it

where children may be present.

Make sure to ground it.

When the product has a protection ground terminal or GND terminal, make sure to ground it.

When theAC line input of it is an inlet type, connect the attached power cable or a power cable suitable for

your area to an outlet with the ground. Otherwise, it may result in electric shock or fire.

Regarding power cable

When a power cable is enclosed or attached to the product, do not use it for other products.

When no power cable is enclosed with the product, prepare the power cable suitable for the usage

environment and area by yourself.

Regarding the connection of power cable

Electrical engineers or the equivalents who have already been familiarized with the proper use and danger

of the product should connect the power cable to theAC input by referring to the instruction manual.

Regarding products that have acquired the safety standard, check the page describing the over-voltage

categories too.

Do not process or damage power cables

It may result in electric shock or fire.

Regarding the input voltage

Check the page describing the input terminals and input voltage in the instruction manual.

Do not provide any voltage out of the specifications.

iii

Matsusada Precision

DOS series

Regarding the fuse

The product builds in a protective fuse. In the case where a fuse holder is arranged outside of the product,

you can replace it by yourself. Refer to the instruction manual to replace it.

In the case where a fuse holder is not arranged outside of the product, you cannot replace it by yourself.

In this case, do not open the case or panel of the product and contact us.

The product is designed for indoor use.

Use the product indoors only, not outdoors. Even indoors, do not use it if there is a possibility of water

leakage, flooding, or snow covering.

Regarding operating temperature and humidity

Use the product within the range of the specifications describing in the instruction manual.

Do not use it in a place where the ambient temperature exceeds the specified range or a closed place.

Do not install the product in places where condensation may occur.

Otherwise, insulation deteriorates and it may cause electric shock, fire, or malfunction.

Do not place anything on top of the product.

Otherwise, they may fall or tumble from it.

Do not put anything into the product.

Do not put foreign objects such as metal or liquid into the product through the air inlets, air outlets, or other

openings. Otherwise, it may result in electric shock, fire, or malfunction.

Operate the product with the right hand.

Use only your right hand to operate the product and keep your left hand away from it, which can reduce

the risk of electric current flowing through the left hand to the vital organs of the body in the event of an

electric shock.

Do not touch the wiring/load connected to the output and any terminals/connectors during the

operation or just after turning output off.

Very high-voltage is on the terminals and connectors during the operation and even just after the output is

turned off. Touching them may result in serious injury or death by electric shock.

The terminals here mean all terminals like input and output terminals and terminals for communications

and remote controls.

Turn off the product before touching the wiring/load connected to the product and any

terminals/connectors on the product and cut it off from the AC input.

Before touching the terminals/connectors and wiring/load, turn off the product and unplug the AC input

cable from the outlet or turn off the AC input breaker. Then, check there is no voltage remained using a

tester.

Since the output and sense terminals are connected to condensers in it, there is high-voltage remained on

them even just after it is turned off.

In order to avoid electric shock, ground the terminals to discharge using a short-circuit grounding

apparatus and check the voltage again.

The terminals here mean all terminals like input and output terminals and terminals for communications

and remote controls.

Matsusada Precision

DOS series

Level the product out to use for good heat dissipation.

Do not install the product upside down or sideways. If not, the inner heat dissipation will be insufficient.

It may result in smoke or fire due to components deterioration.

Do not install the product in a place where cold air directly blows to it.

It may result in electric leakage or burnout due to condensation.

Do not install the product in a place where it is exposed to corrosive gases or liquids.

It may result in smoke or burnout due to components deterioration.

Do not install the product in a dusty place.

Accumulating dust in the air inlet will make hard to cool it down it, it may result in malfunction.

In that case, remove dust immediately.

Do not block the air inlet and outlet.

Secure 30 cm space at least around the openings.

If they are blocked, the product cannot show the rated performance due to the internal temperature

increase. Moreover, components deteriorate and it may result in smoke or fire.

Remove wiring to and from the product when work like welding near it is done.

Do not wipe the equipment with a dust cloth wet with chemicals (thinner or the like) or water.

Otherwise, it may result in an electric shock, electric leakage, or burnout due to water getting inside.

Regarding fan replacement

When products equip a fan, it has a lifetime. It will be worn out and deteriorated with the time passed and

its operation may become unstable. Also, its lifetime greatly varies depending on the usage environment

such as temperature, humidity, dust. It requires to be replaced at regular intervals to extend the lifetime.

For the replacement, contact us.

(It requires a replacement charge separately. Do not replace it by yourself, as there is a risk of electric

shock.)

Table of Contents

Matsusada Precision

DOS series

Table of Contents

Page

For Safe Use of the Product.................................................................................................................................. i

Table of Contents ................................................................................................................................................. v

1 Introduction........................................................................................................................................................1

1 Introduction.................................................................................................................................................11- Overview.....................................................................................................................................................11-2 Applications................................................................................................................................................11-3 Features .....................................................................................................................................................21-4 Lineup.........................................................................................................................................................21-5 Specifications.............................................................................................................................................31-6

Before Use ........................................................................................................................................................42 1 Unpacking................................................................................................................................................... 42- Initial Inspection..........................................................................................................................................42-2 Precautions for Use....................................................................................................................................42-3 Installation ..................................................................................................................................................5

2-4 1 Installation Conditions .........................................................................................................................52-4-

Characteristics of Bipolar Power Supplies.................................................................................................62-5

External Appearance.........................................................................................................................................83 1 300W Model or Lower................................................................................................................................83- 600W to 720W Model.................................................................................................................................93-2 1,200W/2,000W Model.............................................................................................................................103-3

Operation.........................................................................................................................................................134 1 I/O Connection .........................................................................................................................................134- 1 Connecting Load ...............................................................................................................................134-1- Connecting AC Input Cable...............................................................................................................134-1-2

Remote Sensing (for DC Operation)........................................................................................................144-2 Operation Procedure................................................................................................................................154-3 Voltage/Current Monitor ...........................................................................................................................154-4 CV/CC Mode Setting................................................................................................................................154-5 BIAS .........................................................................................................................................................154-6 Other Functions........................................................................................................................................164-7 Overcurrent Protection (OCP)..................................................................................................................164-8 Output Range...........................................................................................................................................164-9 Remote Switch ON/OFF ........................................................................................................................174-10 Interlock Function................................................................................................................................... 174-11

Options............................................................................................................................................................195 1 Canceling Power Failure Protection (-LN)...............................................................................................195- rms Display (-LPr) ....................................................................................................................................195-2 Master/Slave Option (-LMsm)..................................................................................................................195-3 Floating Ground (-LF)...............................................................................................................................195-4 Output Voltage Limiter (-LVc)...................................................................................................................195-5 Output Current Limiter (-LCc)...................................................................................................................205-6

Master/Slave Option (-LMs)............................................................................................................................216 1 Connecting Master and Slave Units.........................................................................................................216- Master/Slave Operation Procedures........................................................................................................226-2 Usage Notes.............................................................................................................................................226-3

1 Introduction

Matsusada Precision

DOS series

Introduction

1-1 Introduction

Thank you very much for your purchase of Fast Response Bipolar Power supply.

We have taken all possible measures to control the quality of our products.

For the best performance and safe use, handle the product correctly according to this manual.

We have carefully prepared this manual, but if you find any doubtful or unclear points, errors, or any

omission, please contact us.

1-2 Overview

DOS series, four-quadrant bipolar power supply features high speed and slew rate DC to 200kHz (in CC

mode). You can also use the product in combination with a function generator, so it can output various

waveforms of sinusoidal, saw-tooth, and rectangular. Moreover, the product amplifies any waveform that

is suited for all sorts of simulation tests.

Power sources and sinks power in four-quadrant operation, and Constant voltage (CV) mode / Constant

current (CC) mode is available. In addition to multiple functions and ultra-high-speed response, the

compact bipolar power supply employs its large and easy to read meter and provides high operability. You

can use the product safely at any time in any location, from laboratories to production line testing.

following accessories are enclosed with the unit body.

If the accessories are different, missing, or broken, please contact us immediately.

1-3 Applications

Inductive load (coil, transformer, etc.)

Ripple test of capacitors

Various tests of motors

Voltage regulation tests of in-vehicle component

Evaluation test of solar cell (photovoltaic cell) related equipment

Surface treatment

Note that the product cannot be used for battery charge/discharge testing.

Matsusada offers a wide lineup of power supplies according to the applications. Feel free to contact out

sales representatives for details.

1 Introduction

Matsusada Precision

DOS series

1-4 Features

Ultra-high speed response and high power

With ultra-high speed and slew rate DC to 200kHz and up to 2,000 W, the product is suited for

transient response testing.

Four-quadrant operation

The product can also be used as a DC electronic load.

DC bias

The 10-turn potentiometer can be used as the output setting volume for DC output or the bias

setting dial for AC waveform output.

Constant voltage (CV) mode / Constant current (CC) mode

The CV/CC mode is easily switched just by the CV/CC toggle on the front panel.

Compact and lightweight design

DC output meter

The 3-digit digital meters indicate the DC values of the output voltage/current. The rms value display

is optionally available.

Complete protective functions

Overvoltage protection (OVP), Overcurrent protection (OCP), and Output short-circuit protection are

provided.

Master-Slave control

With the Master/Slave option, the product offers high output power.

The slave unit as well as master unit can be used as the individual amplifier.

(Note that the frequency response will vary during the master-slave operation. For details, contact

our representatives.)

1-5 Lineup

Model

Maximum

output voltage

[V]

Maximum

output current

[A]

Maximum

output power

[W]

Frequency response (-3dB)

Weight

[kg]

CV mode

CC mode

DOS20-7.5

±20

±7.5

150

DC to

200kHz

DC to

100kHz

DOS20-15

±15

300

DOS20-30

±30

600

DOS20-60

±60

1,200

DOS20-100

±100

2,000

DOS25-6

±25

±6

150

DOS25-12

±12

300

DOS25-24

±24

600

DOS25-48

±48

1,200

DOS25-80

±80

2,000

DOS45-3.3

±45

±3.3

150

DOS45-6.6

±6.6

300

DOS45-13.3

±13.3

600

DOS45-16

±16

720

DOS45-26.7

±26.7

1,200

DOS45-44.4

±44.4

2,000

DOS60-2.5

±60

±2.5

150

DOS60-5

±5

300

DOS60-10

±10

600

DOS60-20

±20

1,200

DOS60-33.3

±33.3

2,000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Matsusada Precision Stromversorgung Handbücher

Matsusada Precision

Matsusada Precision RKT Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision PVCE Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision R4G Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision EQ Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision PZM-0.12BS Bedienungsanleitung

Matsusada Precision

Matsusada Precision DOEF Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision Xpg Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision R4G Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision DRJ Series Installationsanleitung

Matsusada Precision

Matsusada Precision ASX-3R5 Bedienungsanleitung

Matsusada Precision

Matsusada Precision ECD-BC Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision ES Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision R4G Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision PSS2en-DCPS Bedienungsanleitung

Matsusada Precision

Matsusada Precision XR Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision AK Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision CO Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision CD Series Installationsanleitung

Matsusada Precision

Matsusada Precision EPR Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision R4K-36 Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision PRKT Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision ECA Series Bedienungsanleitung

Matsusada Precision

Matsusada Precision R4GN Series Installationsanleitung

Matsusada Precision

Matsusada Precision CO Series Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung